We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery). 

In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.
Can I legally buy/build and ride an ebike that’s faster than 20 mph? Yes you can, but you need to know that the ebike is no longer considered equivalent to a bicycle and is subject to other state vehicular classifications. The definitions for electric bikes spanning 20-30mph, and 1-2 horsepower ranges, will vary from state to state, resulting in a no-man’s-land consensus about limits for motor vehicle definition. The common label for a 20-30mph, 2-wheeled vehicle with active pedals is a Moped. Other MVA labels include motor scooter, motorbike and dirt bike which may have equivalent power and speed performance, but do not have pedals to assist and move the vehicle.
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
Great bike. Easy to assemble by yourself but if you have a rack let pros do it. No charge for that. Contacted the Addmotor people a few times and they got back quickly even on weekends. Great service. Bike is solid as a rock and excellent components. Only drawback is lack of fenders which I hope someone can manufacture. I would buy again in a nano second!

Alberta identifies e-bikes as "power bicycles" and is consistent with the federal definition of "power-assisted bicycle" in MVSR CRC, c 1038 s 2.[19] Motor output must not exceed 500 W (0.671 hp) and e-bikes cannot travel faster than 32 km/h (20 mph). Fully operable pedals are required. No driver's license, vehicle insurance, or vehicle registration is required. Operators must be 12 years of age or older. All operators are required to wear a motorcycle helmet meeting the standards set in AR 122/2009 s 112(2).[20] A passenger is permitted only if the e-bike is equipped with a seat designated for that passenger.[21]
In the 1870s many cycling clubs flourished. They were popular in a time when there were not cars on the market and the principal mode of transportation was horse-drawn vehicles, such the horse and buggy or the horsecar. Among the earliest clubs was The Bicycle Touring Club, which has operated since 1878. By the turn of the century, cycling clubs flourished on both sides of the Atlantic, and touring and racing became widely popular. The Raleigh Bicycle Company was founded in Nottingham, England in 1888. It became the biggest bicycle manufacturing company in the world, making over two million bikes per year.[31]
Attitudes to electric bikes have changed in recent years. For a long time they were seen by cyclists as 'cheating' and by non-cyclists as being just like a bike, but uglier and far more expensive. This new breed of best-in-class electric bikes feel more natural, look more normal, and people are coming around to the idea that a ride with the convenience of a bike but without all the sweat and effort is a Very Good Thing. 
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
Electric Motorcycles News (EMN) has been launched in March 2017 and is a personal initiative from graphic designer Guy Salens (Belgium) to inform you about electric motorcycles, electric scooters and some offroad performance e-bikes. EMN collects and publishes all kind of info from available sources on the internet: press releases, existing website content from manufacturers. EMN has also developed a search engine where you can search for e-dealers with your specific keywords, in different countries, different brands and/or categories.
Nebraska defines a Moped as "a bicycle with fully operative pedals for propulsion by human power, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters which produces no more than two brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than thirty miles per hour on level ground."[69]
Bicycles and horse buggies were the two mainstays of private transportation just prior to the automobile, and the grading of smooth roads in the late 19th century was stimulated by the widespread advertising, production, and use of these devices.[9] More than 1 billion bicycles have been manufactured worldwide as of the early 21st century.[1][2][3] Bicycles are the most common vehicle of any kind in the world, and the most numerous model of any kind of vehicle, whether human-powered or motor vehicle, is the Chinese Flying Pigeon, with numbers exceeding 500 million.[1] The next most numerous vehicle, the Honda Super Cub motorcycle, has more than 60 million units made, while most produced car, the Toyota Corolla, has reached 35 million and counting.[4][5][6][32]

I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have


Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.
Electric bicycles are not allowed in any public area, meaning an area where there is full or partial public access. Any kind of pedal assist, electric bike, scooter, moped or vehicle which has any form of propulsion, whether in full or as assist, other than human power, must be approved as either a car, motorcycle, van, truck, bus or similar. This makes pedelecs and tilt-controlled two-wheel personal vehicles illegal in all practical ways, as they cannot be registered as a motor cycle.[36]

Electrically-assisted cycles are usually classified as either pedelecs or e-bikes. Under European Union regulations adopted in the UK in June 2003, only power-assisted cycles meeting the pedelec classification are considered to be pedal cycles. The maximum power allowed in the European Union for (pedelec) electric bicycles is 250 W, with a maximum assisted speed of 25 km/h.[15]. To meet the pedelec specification the electric motor must be activated by the rider's pedalling effort and the power must cut out completely whenever the rider stops pedalling. Control of the motor by pedalling is often the key difference between a pedelec and e-bike.
What exactly is an electric bike? How can they be used for transportation and why do they make financial sense? These are some of the questions my site http://electricbikereview.com and this channel aim to help you answer. This particular video provides an overview of the Easy Motion Neo Jumper ebike and then follows me on an actual commute to work in Austin Texas.

The Pivot Shuttle breaks the mold when it comes to e-mountain bikes. This ballsy, carbon-frame bike, with Shimano Di2, has 140mm of rear travel, 150mm up front, and a 150mm dropper post. A Shimano STePS e8000 drive unit, paired with a 500Wh battery, provides 20 mph of pedal assist, so you can skip the lift line when you hit the bike park and zip right to the good stuff. The 27.5-inch wheels are nimble and eat up nearly anything in their path, and the massive 2.8-inch tires have huge knobs that grip the trail like Velcro.
We bought 2 of these to go along with our AW 26"x1.75" Front Wheel Electric Bicycle Motor Kits and they work perfectly! The batteries that came with and were recommended by the wheel manufacturer were "clunky", had to be mounted in hanging bags and just didn't work well. These Li-ion Battery with Battery Holders are sleek, fit our Beach Cruisers perfectly, give us a rack to carry our "beach stuff" and one of the best features is how easy they are to charge! They lock in place when we are out and about, but I can unlock them, slide them both out and take them into the RV for charging when we return. Very happy with these and would recommend to anyone looking to convert their current bike into e-bikes!
Our hope is that this plug will become to motors in the 500-1500 watt power range what the 9pin Z910 became for the low power geared motors, with all motor manufacturers agreeing to the same pinout standard for easy swapping and interchangeability . We have an L10 version of the Phaserunner motor controller available now and will soon be expanding this to a Grinfineon offering as well.
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.
None of this would matter if the VanMoof Electrified S2 (and its close relative the X2) wasn't fun to ride, but it is a blast. Like the Brompton, it pulls off the neat trick of powering you along but giving the illusion that you're doing the work, reacting quickly and cleverly to the speed of your pedalling and the difficulty of any incline you're on. 
E-bikes are classed according to the power that their electric motor can deliver and the control system, i.e., when and how the power from the motor is applied. Also the classification of e-bikes is complicated as much of the definition is due to legal reasons of what constitutes a bicycle and what constitutes a moped or motorcycle. As such, the classification of these e-bikes varies greatly across countries and local jurisdictions.

Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]
The Wavecrest Tidalforce M-750 was based on The original military experimental M-313 model. The M-313/M-750X was the first electric bike to be made and tested by Wavecrest Labs. It is based on a design developed for the Defense Advanced Research Projects Agency (DARPA) that was meant to allow zero-heat long distance troop movements for the United States Marine Corps in Afghanistan. The rear wheel in-hub motor and 36 volt/8ah front-hub battery were mounted onto a standard Montague Bicycles Paratrooper Bicycle frame. The 1000 watt rear hub motor had no set speed restriction, but was limited to about 25-32 (depending on load weight) MPH on a flat course. The distance the bike traveled on a single charge ranged from 15 miles (heavier load with no pedaling) to about 25 miles (vigorous assisted pedaling with less hill climbing).
Available products (motors, senors, batteries, control systems. etc.) change fast since the e-bike market shows a strong growth. In principle, get a rear motor if you want a lot of raw power and acceleration (e.g. for a 500W motor). Middle motors are more energy efficient and less subject to problems (e.g. overheating). Middle motors usually are combined with integrated rear hub gears, and rear motors with derailleurs. Both have advantages and disadvantages. E.g. the former require less maintenance, are easy to use in go-and-stop traffic, but require taking off weight on pedals when shifting. Therefore the latter (derailleurs) are better for speedy overland and hills cycling.
More powerful pedelecs which are not legally classed as bicycles are dubbed S-Pedelecs (short for Schnell-Pedelecs, i.e. Speedy-Pedelecs) in Germany. These have a motor more powerful than 250 watts and less limited, or unlimited, pedal-assist, i.e. the motor does not stop assisting the rider once 25 km/h has been reached. S-Pedelec class e-bikes are therefore usually classified as mopeds or motorcycles rather than as bicycles and therefore may (depending on the jurisdiction) need to be registered and insured, the rider may need some sort of driver's license (either car or motorcycle) and motorcycle helmets may have to be worn.[14] In the United States, many states have adopted S-Pedelecs into the Class 3 category. Class 3 ebikes are limited to <=750 watts of power and 28 mph.[15]

Some power-on-demand only e-bikes can hardly be confused with, let alone categorised as, bicycles. For example, the Noped is a term used by the Ministry of Transportation of Ontario for e-bikes which do not have pedals or in which the pedals have been removed from their motorised bicycle. These are better categorised as electric mopeds or electric motorcycles.

In the 1870s many cycling clubs flourished. They were popular in a time when there were not cars on the market and the principal mode of transportation was horse-drawn vehicles, such the horse and buggy or the horsecar. Among the earliest clubs was The Bicycle Touring Club, which has operated since 1878. By the turn of the century, cycling clubs flourished on both sides of the Atlantic, and touring and racing became widely popular. The Raleigh Bicycle Company was founded in Nottingham, England in 1888. It became the biggest bicycle manufacturing company in the world, making over two million bikes per year.[31]
Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.
The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop.  They were among the early shops to embrace family friendly cargo bikes and  appreciated the role that electric would play in making cycling more broadly appealing.
While falling gas prices have temporarily halted years of gains in the number of bicycle commuters, more and more of us are using the bicycle to get around. It’s economical, provides good exercise, and is much cheaper than owning a car. But unless you’re in really good shape, you aren’t going to get very far. Enter the electric bike: a glorious new contraption allows us to get around without having to worry about arriving at our destinations a sweaty mess.
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:

In conformance with legislation adopted by the U.S. Congress defining this category of electric-power bicycle (15 U.S.C. 2085(b)), CPSC rules stipulate that low speed electric bicycles[64] (to include two- and three-wheel vehicles) are exempt from classification as motor vehicles providing they have fully operable pedals, an electric motor of less than 750W (1 hp), and a top motor-powered speed of less than 20 miles per hour (32 km/h) when operated by a rider weighing 170 pounds.[65] An electric bike remaining within these specifications is subject to the CPSC consumer product regulations for a bicycle. Commercially manufactured e-bikes exceeding these power and speed limits are regulated by the federal DOT and NHTSA as motor vehicles, and must meet additional safety requirements. The legislation enacting this amendment to the CPSC is also known as HR 727.[66] The text of HR 727 includes the statement: "This section shall supersede any State law or requirement with respect to low-speed electric bicycles to the extent that such State law or requirement is more stringent than the Federal law or requirements." (Note that this refers to consumer product regulations enacted under the Consumer Product Safety Act. Preemption of more stringent state consumer product regulations does not limit State authority to regulate the use of electric bicycles, or bicycles in general, under state vehicle codes.)
Under the Guide Section of EBR, Court has written a full article, dedicated to the new classification approach, which was initiated by the BPSA (Bicycle Product Suppliers Association), supported by PeopleForBikes, and then Calbikes. The initiative was meant to be pro-active with ebike legislation, to establish self-imposed, measurable, distinct classes of electric bikes before states start hearing about anecdotal problems and potentially overreact to the technology with wide sweeping limitations.
Around the turn of the 20th century, bicycles reduced crowding in inner-city tenements by allowing workers to commute from more spacious dwellings in the suburbs. They also reduced dependence on horses. Bicycles allowed people to travel for leisure into the country, since bicycles were three times as energy efficient as walking and three to four times as fast.

Can I legally buy/build and ride an ebike that’s faster than 20 mph? Yes you can, but you need to know that the ebike is no longer considered equivalent to a bicycle and is subject to other state vehicular classifications. The definitions for electric bikes spanning 20-30mph, and 1-2 horsepower ranges, will vary from state to state, resulting in a no-man’s-land consensus about limits for motor vehicle definition. The common label for a 20-30mph, 2-wheeled vehicle with active pedals is a Moped. Other MVA labels include motor scooter, motorbike and dirt bike which may have equivalent power and speed performance, but do not have pedals to assist and move the vehicle.
Generally they are considered vehicles (like motorcycles and pedal cycles), so are subject to the same rules of the road. Regulations may define maximum power output and for electric bikes may or may not require an interlock to prevent use of power when the rider is not pedaling. In some cases regulatory requirements have been complicated by lobbying in respect of the Segway HT.
The electric bike revolution has officially crossed into the arena of off-road motorbikes. For those who prefer riding in nature, Cake introduced a product which not only respects the environment but other riders, as well. Cake’s Kalk is a silent off-road motorbike that releases no emissions into the atmosphere. Additionally, its electric motor means no gear changing or clutching — a silent motorbike that won’t detract from the experience of others. Perhaps the best part is Cake avoided any sacrifice in performance. The Kalk reaches speeds of fifty miles per hour and features three distinct driving modes: Discover, Explore, and Excite.
This upgraded model is the best scooter of this type that is currently available on the market. I have permanent mobility issues because of my left leg that do not allow me to walk any long distances. This scooter is allowing me to finally get out of the house to see and do some things again, even if that is just cruising around the neighborhood, but my main reason for purchasing it was so that I can go watch my granddaughters playing softball this spring, they are quite good.
In Opinion No. 2007-00602 of the Attorney General, Jim Hood clarified that a "bicycle with a motor attached" does not satisfy the definition of "motor vehicle" under Section 63-3-103. He stated that it is up to the authority creating the bike lane to determine if a bicycle with a motor attached can be ridden in bike lanes. No specifications about the motor were made.

If you are an experienced rider this is actually annoying as hell. Personally, I tend to leave whatever I'm riding in a high gear all the time, because my body is like a powerful machine, and I found the way it slowed my escape from the lights quite disconcerting. For beginners, it could be useful, but it's worth remembering that the whole point of e-bikes is that the motor helps you along anyway, so I do really question the usefulness of this.
Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.

J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
×