In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.
Bicycles were introduced in the late 19th century in Europe, and by the early 21st century, more than 1 billion were in existence at a given time. These numbers far exceed the number of cars, both in total and ranked by the number of individual models produced. They are the principal means of transportation in many regions. They also provide a popular form of recreation, and have been adapted for use as children's toys, general fitness, military and police applications, courier services, bicycle racing and bicycle stunts.
When you have the electric motor turned on, it engages with your first push of the pedals. The difference in acceleration is startling compared to any other bike I've ridden. In Eco mode, I could sprint from 0 to 20mph in about 200 feet/65m. Switch to Turbo, and it's about 150/30m feet. As I mentioned above, you still have to pedal. The difference with an electric bike is the feeling of getting more bang for the buck. And if you want to be lazy, you can. Stay in third or fourth gear and you'll be able to stay around 18-19mph with minimal effort. But if you want to go much faster than 20mph, you'll need to work.
"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Chapter 551., titled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D. The following definition of electric bicycle was passed by the Texas legislature in 2001. "Electric bicycle" means a bicycle that is designed to be propelled by an electric motor, exclusively or in combination with the application of human power, cannot attain a speed of more than 20 miles per hour without the application of human power; and does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle on a highway that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle on a highway used primarily by pedestrians.
Before you start shopping around for a new e-bike, the first thing you should ask yourself is, “how do I plan on using an electric bicycle?” How far do you plan on traveling? What type of terrain will you be traveling on? How much assistance do you need? Do you plan on pedaling – or do you want the bike to do all the work? Is this bike for daily commuting or casual riding? How fast do you need to go?
Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).
If you want an e-bike that positively sprays tech out you, try the Volt Axis on for size. It takes the GoCycle GS's combo of folding, lightweight frame and disk brakes and adds automatic gears, if you please. These react to your speed and pedalling effort. So you automatically gear down when you stop at traffic lights – although what self-respecting cyclist does that? – and then back up as you accelerate.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h). An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.. The legislation enacting this amendment to the CPSC is also known as HR 727.
Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle's crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle's standard drive train.
This upgraded model is the best scooter of this type that is currently available on the market. I have permanent mobility issues because of my left leg that do not allow me to walk any long distances. This scooter is allowing me to finally get out of the house to see and do some things again, even if that is just cruising around the neighborhood, but my main reason for purchasing it was so that I can go watch my granddaughters playing softball this spring, they are quite good.
The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations. The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers. If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.
DIY enthusiasts, with tens of thousands of converted bikes using throttle-only, 20+ mph kits, are now officially labeled Moped class. While these bikes handle and pedal-ride just as safely as the class 3 speed pedelecs in many cases, our DIY counterparts will be officially kicked out and left on their own for advocacy and legal acceptance in California. This is a big deal, without a class sticker, any DIY electric bike conversion kit is considered a Moped and not a bicycle.
It appears Tennessee has not passed any legislation that applies to electric bicycles. Some people think the laws pertaining to a Motorized Bicycle should be used for an electric bicycle. However, a Motorized bicycle would be a gasoline powered device per state law as it is defined as "means a vehicle with two (2) or three (3) wheels, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters (50cc) which produces no more than two (2) brake horsepower and is capable of propelling the vehicle at a maximum design speed of no more than thirty miles per hour (30 mph) on level ground." 
The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson), connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry is usually described as the first recognizably modern bicycle. Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2  as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.