My homeowners (State Farm) covers bikes , but assumes $500 per bike. They will add the bikes as personal property, but the premium is excessive (about $300/year per bike, and we have four bikes). I did increase our personal umbrella liability coverage, and it covers us if family members any sort of accident on our e-bikes that injures us or others or others' property, though only covers $500 each for our own bikes (under the homeowners coverage). It was not very expensive to increase the umbrella policy (as it resulted also in a reduced rate on our car insurance).


eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …
A motorized bicycle shall not be operated by any person under sixteen years of age, nor at a speed in excess of twenty-five miles per hour, upon any public highway, private way laid out under authority of statute, way dedicated to public use, or way under the control of park commissioners or body having like powers, within the commonwealth.[99] A motorized bicycle shall not be operated on any way by any person not possessing a valid driver's license or learner's permit. Every person operating a motorized bicycle upon a way shall have the right to use all public ways in the commonwealth except limited access or express state highways where signs specifically prohibiting bicycles have been posted, and shall be subject to the traffic laws and regulations of the commonwealth and the regulations contained in this section, except that the motorized bicycle operator may keep to the right when passing a motor vehicle which is moving in the travel lane of the way, and the motorized bicycle operator shall signal by either hand his intention to stop or turn. Motorized bicycles may be operated on bicycle lanes adjacent to the various ways, but shall be excluded from off-street recreational bicycle paths. Every person operating a motorized bicycle or riding as a passenger on a motorized bicycle shall wear protective headgear conforming with such minimum standards of construction and performance as the registrar may prescribe, and no person operating a motorized bicycle shall permit any other person to ride a passenger on such motorized bicycle unless such passenger is wearing such protective headgear.
We bought 2 of these to go along with our AW 26"x1.75" Front Wheel Electric Bicycle Motor Kits and they work perfectly! The batteries that came with and were recommended by the wheel manufacturer were "clunky", had to be mounted in hanging bags and just didn't work well. These Li-ion Battery with Battery Holders are sleek, fit our Beach Cruisers perfectly, give us a rack to carry our "beach stuff" and one of the best features is how easy they are to charge! They lock in place when we are out and about, but I can unlock them, slide them both out and take them into the RV for charging when we return. Very happy with these and would recommend to anyone looking to convert their current bike into e-bikes!
Massachusetts General Laws define three classes of motorized two-wheeled vehicles: Motorcycle, Motorized bicycle, and Motorized scooter.[98] Although the definition of motorized scooter includes two-wheeled vehicles propelled by electric motors with or without human power, motorized scooter specifically excludes anything which falls under the definitions of motorized bicycle and motorcycle. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. Motorcycle includes any bicycle with a motor or driving wheel attached, with the exception of vehicles that fall under the specific definition of motorized bicycle. Thus, a pedal bicycle with an electric motor or a non-pedal bicycle with an electric motor, automatic transmission, and maximum speed of 30 miles an hour would fall under the definition of motorized bicycle. An electric bicycle that did not meet those restrictions would be either a motorized scooter or motorcycle, depending on specific characteristics.
A human traveling on a bicycle at low to medium speeds of around 16–24 km/h (10–15 mph) uses only the power required to walk. Air drag, which is proportional to the square of speed, requires dramatically higher power outputs as speeds increase. If the rider is sitting upright, the rider's body creates about 75% of the total drag of the bicycle/rider combination. Drag can be reduced by seating the rider in a more aerodynamically streamlined position. Drag can also be reduced by covering the bicycle with an aerodynamic fairing. The fastest recorded unpaced speed on a flat surface is 144.18 km/h (89.59 mph)[41]
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885.[7][8][9] However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.

Electric bikes aren’t just a practical and environmentally conscious solution to gridlock, they also are really fun to ride. On top of all of the persuasive arguments to get an electric bike, I think the Rad Wagon’s best-selling point comes down to enjoyment. Zooming down the street each morning I wasn’t angrily yelling at fellow drivers or rushing not to be late. The bike commute was part of the journey each day, and not just the means I used to get around. There’s a reason so many people loved biking as a kid, and it can be just as fun as an adult.


There are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia.[5]
For many ebike owners, doing their ebike thing usually becomes more than a hobby and good exercise on the weekend with the riding club. It becomes a lifestyle, a utility machine, a darn fun piece of technology on two wheels. As the industry grows and becomes more popular, these unique bikes will be a daily part of many lives and mold into the framework of legal society.

Electric bicycles use batteries as a source of power and a quiet DC motor as a driving mechanism. On most e-bikes the motor is built directly into the wheel (known as a hub motor) and the batteries are discreetly hidden in the rear rack or frame. Electric bikes can be operated just like normal bicycles, but they can also be power-driven by a throttle or pedaled with the help of pedal-assist (PAS or pedelec).
In the 1870s many cycling clubs flourished. They were popular in a time when there were not cars on the market and the principal mode of transportation was horse-drawn vehicles, such the horse and buggy or the horsecar. Among the earliest clubs was The Bicycle Touring Club, which has operated since 1878. By the turn of the century, cycling clubs flourished on both sides of the Atlantic, and touring and racing became widely popular. The Raleigh Bicycle Company was founded in Nottingham, England in 1888. It became the biggest bicycle manufacturing company in the world, making over two million bikes per year.[31]
The aluminum, step-through eJoy is the happy medium between traditional-looking townies that don’t transport much more than the rider and often cumbersome cargo models that are sometimes a challenge to store. With 26-inch wheels, full fenders, a Shimano Alivio nine-speed drivetrain and disc brakes, a wheelbase similar to the average townie, and a big, comfy seat, it has the appearance of a practical everyday cruiser. But its oversize rear rack, silent Bosch Active Line motor, heavy-duty head tube with front-tray mounts (the tray is an add-on), integrated Supernova E3 lights, and roll-over-anything balloon tires hurtle it into hmm-this-could-actually-replace-my-car status. It’s one of the quietest, most convenient, most stylish, and easiest-to-operate e-bikes available.
One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]
The Ohio Revised Code 4511.01 [121] distinguishes motorized bicycles and mopeds from motorcycles or scooters by describing them as "...any vehicle having either two tandem wheels or one wheel in the front and two wheels in the rear, that is capable of being pedaled and is equipped with a helper motor of not more than fifty cubic centimeters piston displacement that produces no more than one brake horsepower and is capable of propelling the vehicle at a speed of no greater than twenty miles per hour on a level surface." One brake horsepower converts to 0.75 kW, or (rounded) 750W. Thus, a bicycle with an electric helper motor operating under 750W, and not propelling the bicycle over 20 mph, does not qualify to be registered under Ohio state law. Local jurisdictions may have other regulations.
Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3 wheeled bicycle (sic.: 3 wheeled bicycle) that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Federal Motor Vehicle Safety Standards for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1-5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for both. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities. [13]
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.
Off the back of our wildly successful demo weekend with Haibike a few weeks ago, we have decided to run a recap of our picks for the 2018 Haibike eBike range. Across Haibike’s wide range of eBikes built for all styles of off-road riding, a lot of different technologies have been used. From a mix … Continue reading The Haibike eBike Range 2018 – The Fully Charged Picks
Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
We spent 46 hours on research, videography, and editing, to review the top choices for this wiki. Thanks to tough, oversized tires and thick frames, fat bikes allow you to take on rugged terrain — such as sand, snow or rocky mountain trails — that would be nearly impossible to manage with a standard bicycle. So imagine what you can accomplish aboard one of these electric models, which are built with motors for extending your rides even further, or for just helping you out on the way back. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best fat tire electric bike on Amazon.

Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]


There are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia.[5]
Even the humble bicycle hasn't escaped the clutches of modern technology. A whole herd of new e-bikes with electric motors are taking to our cities' streets. Adding a motor to a standard cycle does ramp up the price significantly, but it takes much of the effort out of cycling, making your commute to the office a sweat-free experience and allowing you to sit back and enjoy your suburban cruise.
During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.

Introduction A quick of note of my experiences riding a Moustache Dimanche eBike, kindly provided by Fully Charged, on a spectacular 4 day trip, coast-to-coast across Italy. Overall, an amazing experience in terms of the quality of the ride, the scenery and the new experience of quite painless climbing of the many steep hills. I … Continue reading The joys of crossing Italy coast 2 coast on an eBike – by Andreas Credé
To qualify as an electric-assisted bicycle under state law they need to have a seat and fully operable pedals for human propulsion, meet federal motor vehicle safety standards, an electric motor that has a power output of not more than 1,000 watts, maximum speed of not more than 20 mph (electric motor and human power combined), disengages or ceases to function when the vehicle’s brakes are applied, two or three wheels
For many ebike owners, doing their ebike thing usually becomes more than a hobby and good exercise on the weekend with the riding club. It becomes a lifestyle, a utility machine, a darn fun piece of technology on two wheels. As the industry grows and becomes more popular, these unique bikes will be a daily part of many lives and mold into the framework of legal society.
In Opinion No. 2007-00602 of the Attorney General, Jim Hood clarified that a "bicycle with a motor attached" does not satisfy the definition of "motor vehicle" under Section 63-3-103. He stated that it is up to the authority creating the bike lane to determine if a bicycle with a motor attached can be ridden in bike lanes. No specifications about the motor were made.
Geared Hub Motors – Most pre-built e-bikes use brushless geared hub motors. These motors have internal planetary gears that help transfer power from the motor to the wheel. Because of the internal gearing, these motors provide excellent torque but are limited in top speed. On the plus side, the improved torque means better take-off power and hill climbing ability. Plus, less wattage is required to get the motor turning and they’re typically small and lightweight. On pre-built e-bikes, these motors range from 200w-500w and go up to 20mph. But some aftermarket kits can be as powerful as 1000w, with increased top speeds and huge amounts of torque (ideal for extremely hilly terrain). Besides lower top speeds, these motors tend to be expensive and it’s possible the gears will eventually wear out and need to be replaced (this is highly unlikely, they las quite a long time). Good examples are Ancheer bikes.
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[94][95] Helmets are required.
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
“Changes in production and consumption patterns are a crucial element of the sustainability agenda. Communication between product developers and users, and user integration in product development, can serve as a means for organizational as well as individual learning processes, resulting in sustainable product development. [...] Improved methods, such as INNOCOPE (innovating through consumer-integrated product development), tested in this study with a cycle manufacturer and resulting in a new product, a pedelec, are needed for effective communication, activating consumers and enabling them to promote sustainability goals. Through co-operative product development processes key factors facilitating and obstructing the adoption of sustainable innovations may be identified. Such processes can enhance the emergence and diffusion of sustainable product innovations and different forms and bodies of knowledge can be combined. Integrating users' contextual everyday knowledge of the product with the technical knowledge of companies may lead to mutual learning, technical innovations and changes in consumer behaviour.” (Hoffmann, 2007).

Bicycles were introduced in the late 19th century in Europe, and by the early 21st century, more than 1 billion were in existence at a given time.[1][2][3] These numbers far exceed the number of cars, both in total and ranked by the number of individual models produced.[4][5][6] They are the principal means of transportation in many regions. They also provide a popular form of recreation, and have been adapted for use as children's toys, general fitness, military and police applications, courier services, bicycle racing and bicycle stunts.


In most jurisdictions, bicycles must have functioning front and rear lights when ridden after dark. As some generator or dynamo-driven lamps only operate while moving, rear reflectors are frequently also mandatory. Since a moving bicycle makes little noise, some countries insist that bicycles have a warning bell for use when approaching pedestrians, equestrians, and other cyclists, though sometimes a car horn can be used when a 12 volt battery is available.[citation needed]
I'm one of the hardcore cyclists at Ars, along with Jay Timmer and his new-as-of-last-fall road bike as well as copyeditor Kerry Staurseth. I love cycling, and it was a major factor in my dropping 120lb over a 12-month period starting in the summer of 2009. My daily rider/errand-runner is a 1998 Gary Fisher Marlin mountain bike. For longer rides, I use my 2009 Trek XO2 cyclecross bike. I've made a few modifications to it, including removing the bumpy cyclecross tires and swapping out the front 46-tooth chainring for a 50-tooth one. I went with a cross bike over a road bike because I'm still a Clydesdale, and I like the slightly longer wheelbase of a cross bike. I've also briefly owned a 2011 Trek Madone 5.9, which I sold not long after I bought it due to severely screwing up my right knee.
E-bike usage worldwide has experienced rapid growth since 1998. In 2016 there were 210 million electric bikes worldwide used daily.[33] It is estimated that there were roughly 120 million e-bikes in China in early 2010, and sales are expanding rapidly in India, the United States of America, Germany, the Netherlands,[2] and Switzerland.[34] A total of 700,000 e-bikes were sold in Europe in 2010, up from 200,000 in 2007 and 500,000 units in 2009.[35]
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.
×