Rear-Mounted Hub Motor, installed on the rear wheel, are more common on pre-built bikes because they’re easily installed at the factory. For a conversion, it’s a little harder to install than a front hub motor because of the chain, gearing and derailleur. Plus, you may be limited to a 6 or 7-speed freewheel. However, rear wheel drive will provide more torque and is less noticeable than a front hub.
Bosch eBike Systems – eBikes 101 What is an eBike? The eBike is one of the most agile, comfortable vehicles of our time. With the positive impacts on health, environment and society, electric bikes bring a new meaning to smart mobility. Their modern components and simple yet innovative design allow for a variety of eBiking adventures, from trekking through the …
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
We need to support and put our purchasing power behind ebikes sold in the U.S. that are trying to comply with the California rules which allow 500w and 750w nominal motors and establish 3 classes. If these bikes can create a big enough footprint in the market then future U.S. bike rules may universally adopt these standards. It is better than engaging in regulation showdowns without any standardized and unified proposal on the part of the Electric Bike Community.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
The handlebars connect to the stem that connects to the fork that connects to the front wheel, and the whole assembly connects to the bike and rotates about the steering axis via the headset bearings. Three styles of handlebar are common. Upright handlebars, the norm in Europe and elsewhere until the 1970s, curve gently back toward the rider, offering a natural grip and comfortable upright position. Drop handlebars "drop" as they curve forward and down, offering the cyclist best braking power from a more aerodynamic "crouched" position, as well as more upright positions in which the hands grip the brake lever mounts, the forward curves, or the upper flat sections for increasingly upright postures. Mountain bikes generally feature a 'straight handlebar' or 'riser bar' with varying degrees of sweep backwards and centimeters rise upwards, as well as wider widths which can provide better handling due to increased leverage against the wheel.
An itinerant wordsmith with a broad constellation of interests, Lydia Chipman has turned iconoclasm into a livelihood of sorts. Bearing the scars and stripes of an uncommon diversity of experience -- with the notable exceptions of joining a religious order or becoming an artist -- she still can’t resist the temptation to learn something new. Lydia holds a master of arts in English from Georgia Southern University, and a bachelor of arts cum laude in integrative studies from Clayton College. Her expertise is in the areas of robotics, electronics, toys, and outdoors and computer equipment.
Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle's crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle's standard drive train.
These small complaints prove that the Rad Wagon isn’t perfect. But its overwhelmingly positive qualities clearly outweigh the drawbacks. The Rad Wagon handled beautifully on city streets, accelerating with ease and maintaining a charge for extended range. Rad Power bikes also offers an array of helpful accessories—think racks, baskets, panniers, and platforms—that make the bike nearly as convenient as a car. Time and time again I passed cars stuck in traffic on their daily commute and couldn’t help but wondering: Why don’t more people switch from cars to an e-bike?
I bought the 52v 13ah for my 1000w BBSHD build and it is working great. My bike tears it up pretty good with this battery pack. Hopefully I don't run into any problems but so far so good. One thing I learned the hard way - if you use a 52v pack with the 1000w bbshd your battery meter will no longer be accurate. That was one tough ride home with my heavy fat bike!

I bought this bike from a dealer after extensive research on ebikes. The Elby is on par with European commuter ebikes at a better price point, you get a lot for your $ here. Elby is the complete package commuter: lights & a USB charger (for a phone or whatever) are integrated into the motor’s power supply and wired inside the frame. Rugged fenders have heavy-duty cross braces to attach baskets and whatnot. Thick Continental tires make for a comfy ride. The step-through frame is very convenient, built stout enough to carry me (200#) and two loaded baskets down hills and around curves with perfect stability. The motor on this bike is in the rear hub, and having it behind me makes it virtually soundless. The motor (BionX 500 watt) kicks in as soon as you start pedaling, but there is a
What we especially love is how quiet this e bicycle is. If you’re riding down the street or through the park, the gentle hum of the motor is unnoticeable. This is because it’s hidden by the sound of your smooth pedaling. If you’re not into flashy gadgets, any ordinary person would assume you’re riding a conventional peddle bike. This is a great commuter bike.

Conversion kits, on the other hand, are sold and installed separately on traditional bicycles. They are harder to setup and conceal, and require some basic mechanical ability and a little bit of ‘elbow grease’ to install. The advantage of conversion kits is that you can choose almost any standard bicycle, and you have the freedom to change or upgrade components as you go. A conversion kit will also allow you to achieve higher power and speed ratings that are not possible on most pre-built electric bike models. Kits are great for tall or heavy riders because they can opt for a larger bike, with higher power and weight carrying capacity. People living in hilly terrain may require the additional torque to handle extremely large inclines. For people who prefer a specific bike model or just love to go faster, a conversion kit offers enormous flexibility.

(ii) a vehicle equipped with two or three wheels, foot pedals to permit muscular propulsion, and an independent power source providing a maximum of 2 brake horsepower. If a combustion engine is used, the maximum piston or rotor displacement may not exceed 3.05 cubic inches, 50 centimeters, regardless of the number of chambers in the power source. The power source may not be capable of propelling the device, unassisted, at a speed exceeding 30 miles an hour, 48.28 kilometers an hour, on a level surface. The device must be equipped with a power drive system that functions directly or automatically only and does not require clutching or shifting by the operator after the drive system is engaged.


State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[126] Subchapter J of Publication 45 spells out the vehicle requirements in full.
Operators are subject to driving rules and equipment requirements (if applicable) when operated on the public streets or highways (which includes the main traveled portion of the road, shoulder and sidewalk). This means that an operator could be cited for speeding, failure to signal, unsafe change of course, driving on the sidewalk, DWI (this would apply to anywhere in the state and not just the streets/highways), and all other driving rules contained within state law that would apply. They may also not ride more than two abreast and may not impede the normal and reasonable movement of traffic. On a laned roadway, they must operate within a single lane.[citation needed]
Today, China is the world's leading producer of electric bicycles. According to the data of the China Bicycle Association, a government-chartered industry group, in 2004 China's manufacturers sold 7.5 million electric bicycles nationwide, which was almost twice the year 2003 sales;[8] domestic sales reached 10 million in 2005, and 16 to 18 million in 2006.[9] By 2007, electric bicycles were thought to make up 10 to 20 percent of all two-wheeled vehicles on the streets of many major cities.[9] A typical unit requires 8 hours to charge the battery, which provides the range of 25–30 miles (40–50 km),[9] at the speed of around 20 km/h.[8]

The company was founded in 2009 by Tora Harris who graduated from Princeton University with a degree in Mechanical and Aerospace Engineering. While at Princeton, Harris ran track and became a 2-time winner of the NCAA Championship in the High Jump and set several Ivy League track records in the process. Harris went on to win 2 USA National Outdoor Championship Titles and competed in the 2004 Athens Olympic Games.

In full-electric mode, the Pedego City Commuter Classic Electric Bike is capable of moving at up to 20 mph for anywhere from 15 to 30 miles. There are two further options: power-assisted pedaling or fully "unplugged” riding. Renowned Shimano gears are easy to select. Seldom do we come across a product so universally praised by owners. It's not cheap, but comments like "Everything I hoped for!" and "Outstanding!" tell us that it's money well spent.

If you're taking your bike inside, consider one that folds up. The Cyclotricity Wallet has a motor in the front wheel, which takes you up to speed either by assisting your pedalling, or you can sit back and use the throttle by itself. Its folding design makes it slightly easier to get in and out of a building, but its hefty weight means you still won't find it easy to carry onto public transport.


Not all electric bicycles take the form of conventional push-bikes with an incorporated motor. Some are designed to take the appearance of low capacity motorcycles, but smaller in size and comprising of an electric motor rather than a petrol engine. Bicycles of note include the Sakura electric bicycle, which incorporates a 200W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one based on its similarity in appearance.

Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[68]


The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.
Most electric bicycles can be locked using keys supplied by the manufacturer. The key is usually inserted into a switch, which is commonly found on the bicycle's handlebars or on one side of the motor compartment. When switched to the "Off" position, the electrical drive system cannot be turned on. In areas of high risk for bicycle theft, these locking mechanisms are used in conjunction with coil or U locks.
Bicycles featuring pedal power were developed during the subsequent decades of the 19th century, with the most emblematic example being the bicycle we know today as the Penny-Farthing. The bike was named based on the substantial difference in its wheel size resembling the larger and smaller Penny and Farthing coins, respectively. These bicycles were wildly popular among the well heeled upper classes of Europe and America despite their penchant for launching riders head first over the large wheel, not to mention their relative difficulty to mount and dismount.
E-bikes use rechargeable batteries, electric motors and some form of control. Battery systems in use include sealed lead-acid (SLA), nickel-cadmium (NiCad), nickel-metal hydride (NiMH) or lithium-ion polymer (Li-ion). Batteries vary according to the voltage, total charge capacity (amp hours), weight, the number of charging cycles before performance degrades, and ability to handle over-voltage charging conditions. The energy costs of operating e-bikes are small, but there can be considerable battery replacement costs. The lifespan of a battery pack varies depending on the type of usage. Shallow discharge/recharge cycles will help extend the overall battery life.
None of this would matter if the VanMoof Electrified S2 (and its close relative the X2) wasn't fun to ride, but it is a blast. Like the Brompton, it pulls off the neat trick of powering you along but giving the illusion that you're doing the work, reacting quickly and cleverly to the speed of your pedalling and the difficulty of any incline you're on. 
There are individuals who claim to have lost considerable amounts of weight by using an electric bike.[62] A recent prospective cohort study however found that people using e-bikes have a higher BMI.[63] By making the biking terrain less of an issue, people who wouldn't otherwise consider biking can use the electric assistance when needed and otherwise pedal as they are able.[64] This means people of lower fitness levels or who haven't cycled in many years can start enjoying the many health benefits E-bikes have to offer. [1]
The newest entrant in this lower price category is Wing Bikes, a New York City-based company that launched in 2018. Wing wants to be the affordable e-bike for city residents who are sick of shady ride-hailing services and stalled subways. And if you don’t live in a city, that’s fine too: Wing’s e-bikes could be a realistic alternative to owning a car.
Regulations[37] appear to deal with Bicycles with helper motors. No person shall ride a bicycle with a helper motor unless that person holds a valid motor vehicle operator's license. No person shall operate a bicycle with a helper motor at a rate of speed exceeding thirty miles per hour; nor shall any bicycle with a helper motor be operated on any sidewalk, limited access highway or turnpike. Driver's licence is required except if a special permit is obtained by havnig a doctor fill out a certificate and shows they are able to drive the bike with and without the motor assisting.
You are not allowed to drive S-Pedelecs in France even if they are registered legally in your country (e.g. Germany or Switzerland). In other words, if you plan to take your 45h bike that is legal in your country on vacation in another where it is not, you may violate traffic law. Remove the license plate or don't do it. People who commute between countries, are known to hack removable plates with magnets ...
I eventually got used to it over time, but at first having both kids behind me made the bike feel like it would sway to or fro perilously. I think it was just too much weight to navigate safely, and would be fine with younger kids that didn’t come close to the 120-pound weight limit for the rear cargo area. Overall I’m still a bit partial to a box-style bike if I’m hauling multiple kids and want to be able to see what they’re doing.

GPS Firmware: This net update will be much appreciated by people who have a GPS Analogger device with their CA3. With a simple hardware modification to the Analogger circuit, the GPS data will be transmitted from your existing TRS cable back to the Cycle Analyst. You can then see the time of day, your elevation, position, and direction all on the CA3 screen. The firmware also features additional custom views on the main screen, allowing you to replace or toggle the battery voltage with any of these new parameters to get just the display you are after.

Motor position – e-bike motors are positioned on either the front wheel hub, rear wheel hub, or in the middle of the bike between the pedals. There are pros and cons of each, but we think the mid-engine motor gives better weight distribution and the most natural bike riding feel. The pulling sensation you get from a front hub motor in particular can feel a bit unnatural
Rose Heyer and Josie Tabor of Dept Tech, Department of State Information Center, the Secretary of State and the office of ROCK AND BORGELT, P.C., Attorneys at Law, 24500 FORD ROAD, SUITE 10 DEARBORN HEIGHTS, MI 48127-3106, determined electric bicycles are considered mopeds and need registered and licensed. In order to operate an electric bicycle on public streets, the driver must have a valid operator, chauffeur, or special moped license. However, not all electric bicycles are street legal unless they have the following safety equipment: operating brake light, headlight, and turn signals. The local police department must inspect the bicycle using Form TR-54 which is taken with proof of purchase to the DMV. The fee for the plate is $15 for a three year decal, whereas the fine for no decal is $150 per incident.
The bicycle's invention has had an enormous effect on society, both in terms of culture and of advancing modern industrial methods. Several components that eventually played a key role in the development of the automobile were initially invented for use in the bicycle, including ball bearings, pneumatic tires, chain-driven sprockets and tension-spoked wheels.[10]
By 1898 a rear wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel was patented by Mathew J. Steffens. Also, the 1899 Template:US Patent by John Schnepf depicted a rear wheel friction “roller-wheel” style drive electric bicycle.[5] Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his Template:US Patent. Wood’s device used 4 fractional horsepower motors; each rated less than ½ horsepower and connected through a series of gears.[6]

Available products (motors, senors, batteries, control systems. etc.) change fast since the e-bike market shows a strong growth. In principle, get a rear motor if you want a lot of raw power and acceleration (e.g. for a 500W motor). Middle motors are more energy efficient and less subject to problems (e.g. overheating). Middle motors usually are combined with integrated rear hub gears, and rear motors with derailleurs. Both have advantages and disadvantages. E.g. the former require less maintenance, are easy to use in go-and-stop traffic, but require taking off weight on pedals when shifting. Therefore the latter (derailleurs) are better for speedy overland and hills cycling.
EU: EN15194 (EPAC – Electrically Power Assisted Cycles) defines the use pedal-assisted less than 25k/h bikes: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.”

If you're taking your bike inside, consider one that folds up. The Cyclotricity Wallet has a motor in the front wheel, which takes you up to speed either by assisting your pedalling, or you can sit back and use the throttle by itself. Its folding design makes it slightly easier to get in and out of a building, but its hefty weight means you still won't find it easy to carry onto public transport.
There's no question that electric bikes are far better for the environment than petrol-powered car engines. But that doesn't mean they're completely perfect. Making and disposing of batteries can be very polluting. Not only that, but an electric bicycle is still using energy that has to come from somewhere. You may think you're using clean green power, but the electricity you use for getting about might have come from a filthy old, coal-fired power plant or one driven by nuclear energy. (If you're lucky, of course, it might have come from solar panels or a wind turbine!) Electric bikes are nowhere near as environmentally friendly as ordinary push bikes, but nothing is ever perfect—and, as people often say, "the perfect is the enemy of the good." Electric bikes are certainly a step in the right direction. If everyone used them to get about instead of cars, global warming might be less of a problem, and the world would be a far cleaner and healthier place!

I do not recommend hacking a bike into s-pedelec, i.e. make a 25km/h bike go at 45 or faster. If you have an accident you will be in trouble. Just get a legal version. In addition you will have good insurance. Of course, in countries like France or the UK that so far do not know S-Pedelecs, you will have to make a difficult moral choice.... At least, make sure that your rig is safe...
In summary, federal law trumps all States’ laws. That is true with bicycle law, too. States cannot constitutionally pass legislation that reduces or eliminates Federal laws, they can only pass legislation that enacts additional (tighter) restrictions on its people. States can’t define an ebike a bicycle if greater than 750W/20mph, nor can they define an ebike a motor vehicle if less than the Federal Government’s limit of 750 Watts and a top electric-powered speed of 20 MPH.3This is the Federal definition of a low speed electric bike, which equates it to a bicycle.
At the moment this battery is in stock but for local pickup orders only as we are going through the certification testing required for shipping. We've been keeping the 21700 cell offerings on our radar as they start to catch up with the performance specs of the more mature 18650 series and this year it looks like they are finally making the grade. Expect more from us as the year goes on. 
Not all e-bikes take the form of conventional push-bikes with an incorporated motor, such as the Cytronex bicycles which use a small battery disguised as a water bottle.[44][45] Some are designed to take the appearance of low capacity motorcycles, but smaller in size and consisting of an electric motor rather than a petrol engine. For example, the Sakura e-bike incorporates a 200 W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one.[citation needed]
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
We take a look at the phenomenon sweeping the trails across Europe – Electric Mountain Bikes. After extensive research and a visit to Eurobike, our team hand-picked what we feel to be the best electric mountain bikes in 2018 using Yamaha, Shimano and Bosch eBike systems. Following the visit to Eurobike, it was clear that … Continue reading Best Electric Mountain Bikes 2018 – The Fully Charged Picks
Template:Cleanup Template:Split Many countries have Electric bicycle laws which legislated to one extent or another the legality of Electric Bicycles. Countries Like the United States and Canada have Federal regulations governing the safety requirements and standards of manufacture. Other countries like the Signatories of the European Union have agreed to wider ranging legislation covering use and safety for what they term EPAC(Electric pedal assisted cycles).

If a car is at fault in an accident with a bicycle or ebike, their motor vehicle insurance will likely cover your cost for repair and hopefully medical expenses. But what happens if you are at fault, riding an ebike illegally because you did not register it as a Moped? At best, you could be prosecuted under the law. At worst, you could be financially liable for neglect or reckless endangerment via a law suit.

In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.
Many countries have enacted electric vehicle laws to regulate the use of electric bicycles. Countries such as the United States and Canada have federal regulations governing the safety requirements and standards of manufacture. Other countries like the signatories of the European Union have agreed to wider-ranging legislation covering use and safety of their term EPAC (electric vehicles)
Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
Great bike. Easy to assemble by yourself but if you have a rack let pros do it. No charge for that. Contacted the Addmotor people a few times and they got back quickly even on weekends. Great service. Bike is solid as a rock and excellent components. Only drawback is lack of fenders which I hope someone can manufacture. I would buy again in a nano second!
The bicycle was recognized by 19th-century feminists and suffragists as a "freedom machine" for women. American Susan B. Anthony said in a New York World interview on February 2, 1896: "I think it has done more to emancipate woman than any one thing in the world. I rejoice every time I see a woman ride by on a wheel. It gives her a feeling of self-reliance and independence the moment she takes her seat; and away she goes, the picture of untrammelled womanhood."[74]:859 In 1895 Frances Willard, the tightly laced president of the Woman’s Christian Temperance Union, wrote A Wheel Within a Wheel: How I Learned to Ride the Bicycle, with Some Reflections by the Way, a 75-page illustrated memoir praising "Gladys", her bicycle, for its "gladdening effect" on her health and political optimism.[72] Willard used a cycling metaphor to urge other suffragists to action.[72]
The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations.[63] The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.
×