The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
Rear-Mounted Hub Motor, installed on the rear wheel, are more common on pre-built bikes because they’re easily installed at the factory. For a conversion, it’s a little harder to install than a front hub motor because of the chain, gearing and derailleur. Plus, you may be limited to a 6 or 7-speed freewheel. However, rear wheel drive will provide more torque and is less noticeable than a front hub.
Electric mountain bikes have garnered a lot of attention for their ability to help riders go higher, further, and faster on the trail. As a result, there have been some impressive new eMTB models to hit the market in recent years, making it easier than ever to head off-road. Our favorite is the Haibike SDURO HardNine, which comes equipped with a 350-watt Bosch Performance CX drive and a 500 watt-hour battery. This gives it a range of up to 70 miles, along with a top speed of 20 mph, which is plenty fast on singletrack.
Pedelecs are much like conventional bicycles in use and function — the electric motor only provides assistance, for example, when the rider is climbing or struggling against a headwind. Pedelecs are therefore especially useful for people in hilly areas where riding a bike would prove too strenuous for many to consider taking up cycling as a daily means of transport. They are also useful for riders who more generally need some assistance, e.g. for people with heart, leg muscle or knee joint issues.
State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[55] Subchapter J of Publication 45 spells out the vehicle requirements in full.
The bicycle is extraordinarily efficient in both biological and mechanical terms. The bicycle is the most efficient human-powered means of transportation in terms of energy a person must expend to travel a given distance.[38] From a mechanical viewpoint, up to 99% of the energy delivered by the rider into the pedals is transmitted to the wheels, although the use of gearing mechanisms may reduce this by 10–15%.[39][40] In terms of the ratio of cargo weight a bicycle can carry to total weight, it is also an efficient means of cargo transportation.
Oregon Law (ORS 801.258) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed no greater than 20 miles per hour on level ground.[54]
From all the Chinese brands that have come and disappeared, Onway is still standing strong. That means that they have sold enough bikes, and they have been tried and tested enough for customers to know what to expect. So, what can you expect from this Onway bike? Well, for a very affordable price, you will get anything you realistically need in an e-bike – multi-purpose tires for various terrains, LCD display, LED headlights, taillights, a kickstand… Overall build quality and quality of the parts is above average, but there are some things that you will need to change, and seat should be the first on the list. Customer support is not that great, but if you decide to purchase this bike you will get a fun bike, for affordable price that you will be able to assemble and ride in no time.

The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.


During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.
But two other concerns are also front and center when it comes to biking: cost and convenience. Not many people have showers at their places of employment, and who wants to show up to work coated in sweat and stinky for the rest of the day? Electric bikes solve the convenience problem by making the process almost effortless; you can bike for miles—even up and down hills—without breaking a sweat.

Speed Pedelec ebikes – A new classification of bikes called ‘Speed Pedelecs’ have emerged which technically meet the bicycle definition for a 20 mph ebike. These ebikes are designed to max out at 28 mph. Pedelecs are pedal activated vs throttle activated. The weasel words within the definition says, “20mph on motor alone”. Thus, a person who adds their leg power to the motor assist and happens to cruise at 28mph is NOT doing it by motor alone, and therefore the bike is considered to be compliant with the Federal Law. If the rider stops pedaling, the speed pedelec cannot maintain speed. Speed Pedelecs are becoming more popular in Europe and America, which means more models are being offered.
The battery is the pedelec’s power source. It supplies the motor with the electrical energy that is required to provide power assistance when cycling. So it is hardly surprising that there is frequent discussion and “talking shop” about the eBike’s battery in particular. What is the difference between batteries? How far can you go on a fully charged battery? What do you have to remember about storage? Thomas Raica, head of technical customer application, here provides information and advice.
Firstly there's a magnetically-fired locking pin in the rear wheel, triggered by kicking a button on the hub. This is fairly secure in itself and almost impossible to remove without destroying the bike. In London, we'd pair it with a more traditional bike lock so there's a more obvious visual deterrent, though a LED matrix screen on the frame does issue a warning to would-be tea-leafs.
Awesome little machine. My wife loves it. She gets so many people asking her where she got it and that they want one too. I have an 6 speed/ electric bike but she is not comfortable riding it or any bike for that matter but she’s totally comfortable and confident when she rides the swag. Great product. Exceptional quality and cool looking too. You can’t go wrong with this machine for your wife or daughter or whomever wants to ride but doesn’t want anything bulky or to heavy.
On October 5, 2009, the Government of Ontario brought in laws regulating electric bikes in the province. E-bikes, which can reach a speed of 32 kilometres per hour, are allowed to share the road with cars, pedestrians and other traffic throughout the province. The new rules limit the maximum weight of an e-bike to 120 kilograms, require a maximum braking distance of nine metres and prohibit any modifications to the bike's motor that would create speeds greater than 32 kilometres per hour. Also, riders must be at least 16 years of age, wear approved bicycle or motorcycle helmets and follow the same traffic laws as bicyclists. Municipalities are also specifically permitted by the legislation to restrict where e-bikes may be used on their streets, bike lanes and trails, as well as restricting certain types of e-bike (e.g. banning "scooter-style" e-bikes from bicycle trails). E-bikes are not permitted on 400-series highways, expressways or other areas where bicycles are not allowed. Riding an e-bike under the age of 16 or riding an e-bike without an approved helmet are new offences in the legislation, carrying fines of between $60 and $500. E-bike riders are subject to the same penalties as other cyclists for all other traffic offences.

E-bikes can boost bike usage, offer health benefits and use “an order of magnitude less carbon dioxide than a car traveling the same distance,” according to a 2016 research review published in the journal Transport Reviews.  In fact, access to an e-bike increased cycling trips and distances traveled – and nearly doubled the bike as a mode of transportation, observed one Norwegian study.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
Conversion kits, on the other hand, are sold and installed separately on traditional bicycles. They are harder to setup and conceal, and require some basic mechanical ability and a little bit of ‘elbow grease’ to install. The advantage of conversion kits is that you can choose almost any standard bicycle, and you have the freedom to change or upgrade components as you go. A conversion kit will also allow you to achieve higher power and speed ratings that are not possible on most pre-built electric bike models. Kits are great for tall or heavy riders because they can opt for a larger bike, with higher power and weight carrying capacity. People living in hilly terrain may require the additional torque to handle extremely large inclines. For people who prefer a specific bike model or just love to go faster, a conversion kit offers enormous flexibility.

Not all e-bikes take the form of conventional push-bikes with an incorporated motor, such as the Cytronex bicycles which use a small battery disguised as a water bottle.[44][45] Some are designed to take the appearance of low capacity motorcycles, but smaller in size and consisting of an electric motor rather than a petrol engine. For example, the Sakura e-bike incorporates a 200 W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one.[citation needed]


At just 36V and 5.2 Ah, the battery is not designed for long distance travel. GOTRAX claims the Shift S1 has a range of up to 15 miles (25 km), though that’s only with a lower pedal assist level. If you’re going full throttle, 10 miles (15 km) is a better estimate. But with a battery this small, you could easily charge it at your desk or in the corner of the classroom – lengthening your effective range.

Electric-assisted bicycle operators must follow the same traffic laws as operators of motor vehicles (except those that by their nature would not be relevant). The bicycles may be operated two abreast. Operators must generally ride as close as is practical to the right-hand side of the road (exceptions include when overtaking another vehicle, preparing for a left turn, and to avoid unsafe conditions). The bicycle must be ridden within a single lane. Travel on the shoulder of a road must be in the same direction as the direction of adjacent traffic.


Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3-wheeled bicycle that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Canadian Motor Vehicle Safety Standards (CMVSS) for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1–5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for each. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities.[31]

In 2012, two e-bike advocates completed the first 4,000-mile (6,400 km) transcontinental e-bike tour from New York to San Francisco to advocate for e-bikes in major cities across the U.S.[81] Pedego Electric Bikes is the best selling brand in the U.S. Many e-bikes in the United States are standard bicycles converted using a kit. In general, the kits include the motor (the majority of which are hub motors built into the front or rear wheel), a speed controller, throttle (usually twist-grip or thumb throttle), necessary wiring and connectors, and a battery. Several U.S. companies offer conversion kits which also offer advanced lithium battery packs. Major manufacturers also offer complete e-bikes. Trek offers a line of e-bikes using the Bionx system in which the rider programs the controller to determine how much effort the motor will give in response to rider effort, from 25% up to 200% of the rider's power. This system ensures a minimum level of rider participation and is also used to comply with many European laws mandating partial human effort before the motor engages.
Built by a company that’s made cycling equipment for more than four decades, the Vado feels more like a traditional bicycle than almost any other ebike. Its frame and components have been tuned to provide a familiar experience, making it easy for new and long-time cyclists to jump on and start pedaling. Specialized’s heritage shines through nicely, helping separate itself from the competition in an increasingly crowded ebike market.

E-Bikes are the perfect way to ride across any city: stress-free, easy and fast travel, fun exercise, riding in style and ability to carry heavier loads than a normal bike. Practicing what we preach, this Valentine’s Volt partnered with leading London florist Rebel Rebel to deliver flowers all across London. Every hour on the hour 1 lucky person received a beautiful bouquet for free, just because we wanted to share the love!
Recent legislation has passed putting Maryland ebike laws in line with the popular class 1,2,3 systems previously implemented in states such as California. This legislation becomes effective October 2019. The most significant portion of this change is the increased max limit on power and speed. It will be increased from a max of 500w / 20mph to 750w / 28mph (assuming the ebike in question meets class 3 criteria)

The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations.[63] The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.
The Shift S1 isn’t going to blow anyone away with amazing performance, but it is peppy enough to have a lot of fun on. And if you mostly travel by rideshares like Uber or scootershares like Bird, you can probably pay for the S1 after just a few months of cutting out app-based transportation. It’s hard to ask for too much more from such an inexpensive e-bike.

In the theoretical electric bike we considered up above, we had the dynamo/motor driving the back wheel directly, simply by pressing on the tire. Most electric bikes work a different way. They have compact electric motors built into the hub of the back or front wheel (or mounted in the center of the bike and connected to the pedal sprocket). Take a look at the hub of an electric bike and probably you'll see it's much fatter and bulkier than on a normal bike. You can read more about how these motors work in our main article about hub motors.
Electric bikes are becoming a convenient and fun way to commute around a city, but they can be pricey. The average e-bike can cost $3,000, with some models getting up to $5,000 or more. But these prices are dropping, as new models come onto the market — and if you don’t mind giving up some of the glossier, high-tech features like embedded digital displays, retractable cable locks, and and theft tracking and recovery, you can find a really good quality e-bike for under $1,500.
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]
The BC Bike Show is the premier cycling and outdoors event in Western Canada and is happening in just 2 weeks on March 2nd and 3rd. We'll be there of course, and in addition to our exhibitor booth we'll also be hosting Cycle Stage to give more public presentations. On Saturday at 11:45 am we'll talk on how to navigate the various motor and battery options available for ebike retrofits, and on Sunday at 2pm we'll be doing a live demonstration of a regular bicycle being converted over to electric assist.
X-Treme is a very well-known distributor of electric scooters and electric bikes with really great customer service. They offer a number of great budget electric bikes, and one of them is Catalina Beach Cruiser. Powered by 500W rear hub motor, this e-bike can conquer almost any terrain. The frame of this bike is 100% hand-welded aluminum, with a step-though design. The top speed on this bike is about 20 mph, with the range of up to 60 miles on pedal-assist mode. The battery pack is 48V LiPo4. This e-bike is an absolute joy to ride. Even more now, with an all new zero resistance rear hub motor with an automatic clutch. This makes riding without power a breeze and you will feel no resistance from the motor. Seat is large and very comfortable, with dual springs for smooth ride. It also comes with a basket, which is a must have if you plan on going for groceries or running errands on this bike.
A new European product safety standard EN 15194 will be published in 2009. EN 15194 contains several new requirements for ebikes to be sold in European Union and European Economic Area, including weight and voltage limitations. EN 15194 also defines a specific name for EU approved electrically-assisted cycles, EPAC - "Electrically Pedal Assisted Cycle".
As of 2008 a standard class C license, proof of insurance, and registration (annual fee: $9.00) are required for operation of any motorized pedalcycle in Pennsylvania. Additionally, there are strict equipment standards that must be met for operation, including: handlebars, brakes, tires/wheels, electrical systems/lighting, mirrors, speedometer, and horns/warning devices.[127]
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
In the Netherlands all train stations offer free bicycle parking, or a more secure parking place for a small fee, with the larger stations also offering bicycle repair shops. Cycling is so popular that the parking capacity may be exceeded, while in some places such as Delft the capacity is usually exceeded.[64] In Trondheim in Norway, the Trampe bicycle lift has been developed to encourage cyclists by giving assistance on a steep hill. Buses in many cities have bicycle carriers mounted on the front.
State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[126] Subchapter J of Publication 45 spells out the vehicle requirements in full.

In Norway, e-bikes are classified as ordinary bicycles, according to the Vehicle Regulation (kjøretøyforskriften) § 4-1, 5g. Hence, e-bikes are not registered in the Vehicle Registry, and there is no demand for a license to drive them. Still, there are constraints on the bicycle construction. The maximum nominal motor power output can be no more than 250 watts and the maximum performance speed of the vehicle when the engine is running is 25 km per hour (15 mph).[40] A function that reduces motor power when vehicle speed exceeds 25 km per hour is mandatory. However, if the motor is not running, the e-bike, or any other bike, answer only to the constraints of the ordinary speed limits.

×