Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.
In summary, federal law trumps all States’ laws. That is true with bicycle law, too. States cannot constitutionally pass legislation that reduces or eliminates Federal laws, they can only pass legislation that enacts additional (tighter) restrictions on its people. States can’t define an ebike a bicycle if greater than 750W/20mph, nor can they define an ebike a motor vehicle if less than the Federal Government’s limit of 750 Watts and a top electric-powered speed of 20 MPH.3This is the Federal definition of a low speed electric bike, which equates it to a bicycle.
In New Zealand, the regulations read: "AB (Power-assisted pedal cycle) A pedal cycle to which is attached one or more auxiliary propulsion motors having a combined maximum power output not exceeding 300 watts." This is explained by NZTA as "A power-assisted cycle is a cycle that has a motor of up to 300 watts. The law treats these as ordinary cycles rather than motorcycles. This means that it is not necessary to register or license them. Note that the phrase "maximum power output" that is found in the regulation (but omitted in the explanation) may create confusion because some e-bike motor manufacturers advertise and print on the motor their "maximum input power" because that number is larger (typically motors run at about 80% efficiency ) thus give the impression the buyer is getting a more powerful motor. This can cause misunderstandings with law enforcement officers who do not necessarily understand the difference, and when stopping a rider on an e-bike in a traffic stop, look at the number on the motor to determine if the e-bike is legal or not.
Geared Hub Motors – Most pre-built e-bikes use brushless geared hub motors. These motors have internal planetary gears that help transfer power from the motor to the wheel. Because of the internal gearing, these motors provide excellent torque but are limited in top speed. On the plus side, the improved torque means better take-off power and hill climbing ability. Plus, less wattage is required to get the motor turning and they’re typically small and lightweight. On pre-built e-bikes, these motors range from 200w-500w and go up to 20mph. But some aftermarket kits can be as powerful as 1000w, with increased top speeds and huge amounts of torque (ideal for extremely hilly terrain). Besides lower top speeds, these motors tend to be expensive and it’s possible the gears will eventually wear out and need to be replaced (this is highly unlikely, they las quite a long time). Good examples are Ancheer bikes.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885. However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear wheel, or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.
The release of Garmin’s new Edge 520 Plus GPS bike computer made a big splash in the world of cycling. It was an impressive upgrade, likely a response to increasing competition from the likes of Wahoo. But the Garmin Edge 520 Plus upgrade has caused a little confusion, because it seems to offer the same mapping and navigation capabilities as the more expensive Edge 820 and 1030. We clear up the confusion with two in-depth posts, Garmin Edge 520 vs 520 Plus, and Garmin Edge 1030 vs 820 vs 520 Plus.
Electric powered bicycles slower than 20 km/h without pedaling are legally recognized as a non-mechanically operated vehicle in China. According to "TECHNOLOGY WATCH", this should help promote its widespread use. Electric bicycles were banned in some areas of Beijing from August 2002 to January 2006 due to concerns over environmental, safety and city image issues. Beijing has re-allowed use of approved electric bicycles as of January 4, 2006. Some cities in China still ban electric bikes.
Bicycle manufacturing proved to be a training ground for other industries and led to the development of advanced metalworking techniques, both for the frames themselves and for special components such as ball bearings, washers, and sprockets. These techniques later enabled skilled metalworkers and mechanics to develop the components used in early automobiles and aircraft.
The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop. They were among the early shops to embrace family friendly cargo bikes and appreciated the role that electric would play in making cycling more broadly appealing.
Are you looking for an easier way to get to your blind or tree stand? Or perhaps check all your trail cams in a fraction of the time it takes today? Is that sweet spot you know getting harder to reach? When you have to carry 50lbs of gear on your back for 5 or even 10 miles and if you’re lucky you have something to haul back out, using an electric bike built specifically for offroad and woodlands that is also capable of carrying your gear, wouldn’t that make the experience a whole lot more enjoyable? Electric hunting bikes...
During testing—and unlike some of the other bikes I’ve tried—this range held true, with the Rad Wagon handling a 20-plus mile round trip with ease. This is helped by a regenerative braking system that automatically charges the battery whenever you engage the brake levels. It’s also relatively quick to charge back up—taking around four hours in my garage—although Rad Power reports that average time is five to six hours.
But in Great Britain, the European Union definition is applicable, and the tighter restrictions of the Electrically Assisted Pedal Cycle Regulations 1983 (including a 200 kg weight limit on solo bicycles) were removed on 6 April 2015 by the Electrically Assisted Pedal Cycles (Amendment) Regulations 2015. Riders must be at least 14 years of age, but no driving licence is required.
You can learn more about the development and axle testing process on this endless-sphere thread. Our ambition is to make this splined axle design into a new standard that we deploy across our entire higher power motor lines to replace axle flats. If you're as excited as us and want to jump right into ordering, we have the first production shipment on hand available in bare motors and complete kits.
This is a virtual hello to all the people who came by our booth last weekend at the BC Bike Show and are just now visiting our webpage for the first time. We had a great time and were delighted to see how much this event has grown recently. (And to those who lament that the bike show is now totally taken over by ebikes, well it's been over 15 years now that we've been trying to tell you all this day was coming!)