Electric powered bicycles slower than 20 km/h without pedaling are legally recognized as a non-mechanically operated vehicle in China.[32] According to "TECHNOLOGY WATCH", this should help promote its widespread use.[33] Electric bicycles were banned in some areas of Beijing from August 2002 to January 2006 due to concerns over environmental, safety and city image issues. Beijing has re-allowed use of approved electric bicycles as of January 4, 2006.[34] Some cities in China still ban electric bikes.

Tires vary enormously depending on their intended purpose. Road bicycles use tires 18 to 25 millimeters wide, most often completely smooth, or slick, and inflated to high pressure in order to roll fast on smooth surfaces. Off-road tires are usually between 38 and 64 mm (1.5 and 2.5 in) wide, and have treads for gripping in muddy conditions or metal studs for ice.


Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles,[77] including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity.[78] A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.[79]

Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3-wheeled bicycle that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Canadian Motor Vehicle Safety Standards (CMVSS) for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1–5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for each. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities.[31]
Great bike. Easy to assemble by yourself but if you have a rack let pros do it. No charge for that. Contacted the Addmotor people a few times and they got back quickly even on weekends. Great service. Bike is solid as a rock and excellent components. Only drawback is lack of fenders which I hope someone can manufacture. I would buy again in a nano second!
In 5 years of working as a bike messenger in Minneapolis, I've ridden all kinds of bikes, in all kinds of weather. I've ridden walmart mountain bikes, 80's classic steel road bikes, kitted out Treks, pretty much everything EXCEPT for fat tire bikes. Such wide tires always seemed... too much. No need for a bike that only makes itself worthwhile maybe two months out of the year, I thought.

E-bikes can boost bike usage, offer health benefits and use “an order of magnitude less carbon dioxide than a car traveling the same distance,” according to a 2016 research review published in the journal Transport Reviews.  In fact, access to an e-bike increased cycling trips and distances traveled – and nearly doubled the bike as a mode of transportation, observed one Norwegian study.
The Tidalforce Electric Bicycle was an electric bicycle manufactured by Wavecrest Labs from 2003 until the company went out of business in 2006. All models of Wavecrest Tidalforce electric bikes have a 36 volt electric hub motor built into the rear wheel hub and a 36 volt battery pack built into the front wheel hub. Wavecrest Labs manufactured three models of Tidalforce bikes: The Wavecrest Tidalforce M-750, the S-750 Traditional hard tail mountain bike and the iO-750 Cruiser. Any of the three bikes with an X suffix denotes that the motor is a 1000 watt motor without a set speed restriction as compared to the speed limited 750 watt version.

A response to an inquiry made to the Mass DOT/RMV indicates that Massachusetts does recognize the federal low speed electric bicycle Federal Law (15 U.S.C. § 2085) and interprets that to mean these ebikes do not require license or registration. However, some of the materials available on the RMV website do not distinguish between "Motorized Bicycle" and low power ebikes. One form, Bicycle Conversion to Motorized Bike, does document the exemption of low power ebikes.[100]
Every bike on this list has been thoroughly evaluated and vetted by our team of test editors. We research the market, survey user reviews, speak with product managers and engineers, and use our own experience riding these bikes to determine the best options. Our team of experienced testers spent many hours and miles using these bikes for their intended purpose. We’ve commuted to and from work on them, used them to stock up on groceries and beer, tested their passenger-hauling capability, ridden them on questionable terrain (just to see how they’d handle), and run their batteries down to officially see how long they last on one charge. We evaluated them on performance, price, comfort, handling, value, reliability, fun, and overall e-factor to come up with this list of bikes that will best serve the needs of anyone looking to add a little pedal assist to their ride.
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.

The list below should be complete with both a literature analysis and by mining course materials. In principle, everything that can be research also can be education. Therefore we also listed a few items found in the literature. There are some interesting issues that refer to organizational and informal learning, i.e. users participating in design and policy making.

Some US companies, notably in the tech sector, are developing both innovative cycle designs and cycle-friendliness in the workplace. Foursquare, whose CEO Dennis Crowley "pedaled to pitch meetings ... [when he] was raising money from venture capitalists" on a two-wheeler, chose a new location for its New York headquarters "based on where biking would be easy". Parking in the office was also integral to HQ planning. Mitchell Moss, who runs the Rudin Center for Transportation Policy & Management at New York University, said in 2012: "Biking has become the mode of choice for the educated high tech worker".[66]
The release of Garmin’s new Edge 520 Plus GPS bike computer made a big splash in the world of cycling. It was an impressive upgrade, likely a response to increasing competition from the likes of Wahoo. But the Garmin Edge 520 Plus upgrade has caused a little confusion, because it seems to offer the same mapping and navigation capabilities as the more expensive Edge 820 and 1030. We clear up the confusion with two in-depth posts, Garmin Edge 520 vs 520 Plus, and Garmin Edge 1030 vs 820 vs 520 Plus.
"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Chapter 551., titled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D.[58] The following definition of electric bicycle was passed by the Texas legislature in 2001. "Electric bicycle" means a bicycle that is designed to be propelled by an electric motor, exclusively or in combination with the application of human power, cannot attain a speed of more than 20 miles per hour without the application of human power; and does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle[0] on a highway that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle[0] on a highway used primarily by pedestrians.
I purchased version 2.0 of this device and the manufacturer has been listening to comments from users and making running changes such as the three speeds and the rear suspension. I am an XL size user (6'2", 230lbs) and recently returned from a 26 day cruise around Europe. I rode this little scooter on cobblestones, miles and miles through the Vatican, inside ancient cities and all over the streets of San Juan upon our return stateside. There was only one time it was less than ideal and that was going uphill, on slick tile that was wet from a drizzle. It still make it, just had to lean way forward to get weight on the front wheel.

Across Europe, where e-bikes were embraced by the public long before the rest of the world, e-bike growth has averaged in excess of 20 percent each year between 2014 and 2017, with a whopping 25.3 percent growth to a total of two million e-bike sales in 2017. Analysts predict that strong growth will continue, with worldwide e-bike sales expected to hit $23.83 billion by 2025. A lot of that growth will be right here in the US.

Bicycle suspensions are used primarily on mountain bicycles, but are also common on hybrid bicycles, as they can help deal with problematic vibration from poor surfaces. Suspension is especially important on recumbent bicycles, since while an upright bicycle rider can stand on the pedals to achieve some of the benefits of suspension, a recumbent rider cannot.
The Footloose has no chain, however -- it's entirely electrically driven. It takes very little effort to get to your destination, meaning you arrive at work without having broken a sweat. The downside is that when you run out of power, you're not going anywhere. And pedalling from a standstill, waiting for the motor to kick in, is an odd sensation that takes some getting used to.
Track bicycles do not have brakes, because all riders ride in the same direction around a track which does not necessitate sharp deceleration. Track riders are still able to slow down because all track bicycles are fixed-gear, meaning that there is no freewheel. Without a freewheel, coasting is impossible, so when the rear wheel is moving, the cranks are moving. To slow down, the rider applies resistance to the pedals, acting as a braking system which can be as effective as a conventional rear wheel brake, but not as effective as a front wheel brake.[51]

The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.

The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
Electric Bicycles are defined by the California Vehicle Code [32][33]. In summary, electric bicycles are to be operated like conventional bicycles in California. There are several exceptions to this. A person must be at least 16 years old, and anyone riding an electric bicycle must wear a bicycle helmet. The e-bikes must have an electric motor that has a power output less than 1,000 watts, is incapable of propelling the device at a speed of more than 20 miles per hour on level ground, is incapable of further increasing the speed of the device when human power is used to propel the motorized bicycle faster than 20 miles per hour, operates in a manner so that the electric motor is disengaged or ceases to function when the brakes are applied, or operates in a manner such that the motor is engaged through a switch or mechanism that, when released, will cause the electric motor to disengage or cease to function.
E-bikes use rechargeable batteries, electric motors and some form of control. Battery systems in use include sealed lead-acid (SLA), nickel-cadmium (NiCad), nickel-metal hydride (NiMH) or lithium-ion polymer (Li-ion). Batteries vary according to the voltage, total charge capacity (amp hours), weight, the number of charging cycles before performance degrades, and ability to handle over-voltage charging conditions. The energy costs of operating e-bikes are small, but there can be considerable battery replacement costs. The lifespan of a battery pack varies depending on the type of usage. Shallow discharge/recharge cycles will help extend the overall battery life.
"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption, [59][60][61][62][63][64] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
In some countries mixed systems, i.e. pedaling and/or using a throttle is legal. In EU countries and Switzerland this is not the case. I.e. you can buy an electric scooter, but this is not considered to be an e-bike in the moped / light scooter category. That kind of hack is probably more difficult, unless the original design has been modified to fit with (s)Pedelec specs. E.g. The Ezee models are of that kind and modifications to revert to the original does not seem to be too difficult...
Hmm, I think it depends on the forest. My experience has been that if you have a Class 1 ebike and are riding respectfully, most places allow it. I have a sensitive knee and carry a doctor’s note citing disability laws in Colorado and have never been approached or asked by a ranger or fellow rider about the legality of my bike. That said, I have been using the really quiet and hidden Brose motor and I ride carefully and am friendly with everyone 

Are there any guidelines you could give on what is legal in Federal Parks that have duel use pedestrian and bike paths. I was recently told that E bikes are not allowed on a Federal trail even though much faster 10 and 20 speed bicycles are common. I also stated that I have a disability which prevents me from walking or biking very far but was still told my bike was not allowed. I should also add that my bike has a top speed of about 15 and is 250 watts.

We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).


As long as the electric bicycle meets three criteria it is considered a low-speed electric bicycle, or simply a "bicycle." Three criteria: must travel less than 20 mph on flat ground without pedaling, must have functional pedals and must have less than a 750 watt motor. This is the same criteria as Federal Public Law 107-319. I checked my facts with the law office of Spohn, Spohn & Zeigler at 144 East Center Street, Marion, OH 43302 on August 21, 2009. A low-speed electric bicycle does not require registration, insurance, license plates (tags), or a driver's license. The rules of an electric bicycle are the same as a traditional bicycle. There is some confusion caused by Ohio interchanging the word Moped with "motorized bicycle." If a dealer sells you a bike that follows the guidelines of Federal Public Law 107-319, then you have a bicycle. If the bike has no pedals or has a higher wattage motor than 750 watts or can travel faster than 20mph you have a moped or scooter; Ohio requires tags and registration for mopeds and scooters.

E-bikes are classified in three different types: Class 1 and Class 3 bikes are powered proportionally to the “input” a rider gives via pedaling. “It feels natural, and you’re still riding a bike, so all your reflexes, skill and comfort you’ve developed over years of riding bikes apply immediately,” says Fritz Rice, sales manager of Gregg’s Cycles, near Greenlake.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
Further innovations increased comfort and ushered in a second bicycle craze, the 1890s Golden Age of Bicycles. In 1888, Scotsman John Boyd Dunlop introduced the first practical pneumatic tire, which soon became universal. Willie Hume demonstrated the supremacy of Dunlop's tyres in 1889, winning the tyre's first-ever races in Ireland and then England.[28][29] Soon after, the rear freewheel was developed, enabling the rider to coast. This refinement led to the 1890s invention[30] of coaster brakes. Dérailleur gears and hand-operated Bowden cable-pull brakes were also developed during these years, but were only slowly adopted by casual riders.

During nighttime operation, the bicycle must be equipped with a front headlamp, a rear-facing red reflector, and reflectors on the front and rear of pedals, and the bicycle or rider must have reflective surfaces on each side. Minn. Stat. §169.222, subd. 6. An electric-assisted bicycle can be equipped with a front-facing headlamp that emits a flashing white light, a rear-facing lamp that has a flashing red light, or both. The bicycle can carry studded tires designed for traction (such as in snowy or icy conditions).

Nevada	Electric Bicycle (NRS 482.0287)	Bicycle	20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster)	750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft)	No	none (use caution here because of "reckless endangerment" laws)	no (not a "motor vehicle")

Motor-driven cycles may be operated on the roadway without registration, but the operator must have a driver's license.[85] The cycle may not be operated on any sidewalk, limited access highway or turnpike. If the maximum speed of the cycle is less than the speed limit of the road, the cycle must operate in the right hand lane available for traffic or upon a usable shoulder on the right side of the road unless the operator is making a left turn.
The safety bicycle gave women unprecedented mobility, contributing to their emancipation in Western nations. As bicycles became safer and cheaper, more women had access to the personal freedom that bicycles embodied, and so the bicycle came to symbolize the New Woman of the late 19th century, especially in Britain and the United States.[8][73] The bicycle craze in the 1890s also led to a movement for so-called rational dress, which helped liberate women from corsets and ankle-length skirts and other restrictive garments, substituting the then-shocking bloomers.[8]
We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.
I'm one of the hardcore cyclists at Ars, along with Jay Timmer and his new-as-of-last-fall road bike as well as copyeditor Kerry Staurseth. I love cycling, and it was a major factor in my dropping 120lb over a 12-month period starting in the summer of 2009. My daily rider/errand-runner is a 1998 Gary Fisher Marlin mountain bike. For longer rides, I use my 2009 Trek XO2 cyclecross bike. I've made a few modifications to it, including removing the bumpy cyclecross tires and swapping out the front 46-tooth chainring for a 50-tooth one. I went with a cross bike over a road bike because I'm still a Clydesdale, and I like the slightly longer wheelbase of a cross bike. I've also briefly owned a 2011 Trek Madone 5.9, which I sold not long after I bought it due to severely screwing up my right knee.
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead. 
Today I’m looking at the Rattan Challenger 350W ebike. It can be found for under $680 at Amazon (after Electrek coupon code 5AIDO2GB) shipped and includes free assembly at a local bike shop. I assembled mine at home however in about 15 minutes with the graciously supplied in box hex tool and wrenches. It is pretty straight forward – the hardest part was bolting the front light on.
In the 1890s, electric bicycles were documented within various U.S. patents. For example, on 31 December 1895, Ogden Bolton Jr. was granted U.S. Patent 552,271 for a battery-powered bicycle with "6-pole brush-and-commutator direct current (DC) hub motor mounted in the rear wheel". There were no gears and the motor could draw up to 100 amperes (A) from a 10-volt battery.[5]
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.
Put the wheel with the electric hub on your bike and connect the brake components. Simply reverse the process you used to remove the wheel in order to reinstall it. Be sure to adjust the chain so it fits properly if you’re replacing the back wheel. If the bike has rim or cantilever brakes, simply close them over the new wheel using the lever. If the bike has disc brakes, put the pads back in place and secure them using the clips, springs, or cotter or retaining pin.[11]
I discovered these downsides when, on my third day with the bike, I got a flat tire and had to carry it onto the subway with me for those last few miles back to my apartment. The cause of the flat is unknown; the bike mechanic who eventually fixed it didn’t see anything wrong with the rims. But the experience of trying to maneuver an almost 40 pound e-bike on and off a crowded subway car during rush-hour is not one I can recommend.
Bosch eBike Systems – eBikes 101 What is an eBike? The eBike is one of the most agile, comfortable vehicles of our time. With the positive impacts on health, environment and society, electric bikes bring a new meaning to smart mobility. Their modern components and simple yet innovative design allow for a variety of eBiking adventures, from trekking through the …
E-Bikes are the perfect way to ride across any city: stress-free, easy and fast travel, fun exercise, riding in style and ability to carry heavier loads than a normal bike. Practicing what we preach, this Valentine’s Volt partnered with leading London florist Rebel Rebel to deliver flowers all across London. Every hour on the hour 1 lucky person received a beautiful bouquet for free, just because we wanted to share the love!

Are you looking for an easier way to get to your blind or tree stand? Or perhaps check all your trail cams in  a fraction of the time it takes today?  Is that sweet spot you know getting harder to reach? When you have to carry 50lbs of gear on your back for 5 or even 10 miles and if you’re lucky you have something to haul back out, using an electric bike built specifically for offroad and woodlands that is also capable of carrying your gear, wouldn’t that make the experience a whole lot more enjoyable? Electric hunting bikes...
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
By 1898 a rear wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel was patented by Mathew J. Steffens. Also, the 1899 Template:US Patent by John Schnepf depicted a rear wheel friction “roller-wheel” style drive electric bicycle.[5] Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his Template:US Patent. Wood’s device used 4 fractional horsepower motors; each rated less than ½ horsepower and connected through a series of gears.[6]
The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.
We take a look at the phenomenon sweeping the trails across Europe – Electric Mountain Bikes. After extensive research and a visit to Eurobike, our team hand-picked what we feel to be the best electric mountain bikes in 2018 using Yamaha, Shimano and Bosch eBike systems. Following the visit to Eurobike, it was clear that … Continue reading Best Electric Mountain Bikes 2018 – The Fully Charged Picks

State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.
Electric motor assisted bicycles have been banned in the State of New York and are not permitted for on-road use.[50][51] It appears the only known allowance of an electric bicycle is if it is an electric powered moped, at this time. There is a proposed bill to allow ebikes. As of May 2009, Bill A2393("Defines the term electric assisted bicycle") has been passed in the NY State Assembly[52] and its corresponding Bill S4014, sponsored by Senator Thomas Morahan, is before the NY State Senate.[53]

Many countries have enacted electric vehicle laws to regulate the use of electric bicycles. Countries such as the United States and Canada have federal regulations governing the safety requirements and standards of manufacture. Other countries like the signatories of the European Union have agreed to wider-ranging legislation covering use and safety of their term EPAC (electric vehicles)
You can learn more about the development and axle testing process on this endless-sphere thread. Our ambition is to make this splined axle design into a new standard that we deploy across our entire higher power motor lines to replace axle flats. If you're as excited as us and want to jump right into ordering, we have the first production shipment on hand available in bare motors and complete kits.
I like this little electric "scooter" a lot. I do think the rear wheels should be a bit further apart for added stability. I have also found it is too easy to "spin out" the front driver wheel when going up an incline or crossing a grass area. The user and assembly manual is minimal and could use considerably more information and more and better illustrations.
More powerful pedelecs which are not legally classed as bicycles are dubbed S-Pedelecs (short for Schnell-Pedelecs, i.e. Speedy-Pedelecs) in Germany. These have a motor more powerful than 250 watts and less limited, or unlimited, pedal-assist, i.e. the motor does not stop assisting the rider once 25 km/h has been reached. S-Pedelec class e-bikes are therefore usually classified as mopeds or motorcycles rather than as bicycles and therefore may (depending on the jurisdiction) need to be registered and insured, the rider may need some sort of driver's license (either car or motorcycle) and motorcycle helmets may have to be worn.[14] In the United States, many states have adopted S-Pedelecs into the Class 3 category. Class 3 ebikes are limited to <=750 watts of power and 28 mph.[15]
Speed Pedelec ebikes – A new classification of bikes called ‘Speed Pedelecs’ have emerged which technically meet the bicycle definition for a 20 mph ebike. These ebikes are designed to max out at 28 mph. Pedelecs are pedal activated vs throttle activated. The weasel words within the definition says, “20mph on motor alone”. Thus, a person who adds their leg power to the motor assist and happens to cruise at 28mph is NOT doing it by motor alone, and therefore the bike is considered to be compliant with the Federal Law. If the rider stops pedaling, the speed pedelec cannot maintain speed. Speed Pedelecs are becoming more popular in Europe and America, which means more models are being offered.
If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
The Netherlands has a fleet of 18 million bicycles.[77] E-bikes have reached a market share of 10% by 2009, as e-bikes sales quadrupled from 40,000 units to 153,000 between 2006 and 2009,[78] and the electric-powered models represented 25% of the total bicycle sales revenue in that year.[77] By early 2010 one in every eight bicycles sold in the country is electric-powered despite the fact that on average an e-bike is three times more expensive than a regular bicycle.[73][78]

State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[126] Subchapter J of Publication 45 spells out the vehicle requirements in full.


I called Geico earlier today. They could insure me with Renters Insurance, but … I would need to have a Renter's Policy first, before the secondary insurance company they deal would insure my two bikes (Surly Long Haul Trucker and Yuba Sweet Curry custom eBike). BUT … unfortunately …. The company that would insure my bicycles will NOT insure me because we have a Pitbull !!! Can you believe that … !!!
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.
×