The oldest patent for an electric bike I've been able to find at the US Patent and Trademark Office is this one, by Ogden Bolton, Jr. of Canton Ohio, which was filed in September 1895 and granted three months later. You can see from these original diagrams that it bears an amazingly close resemblance to modern electric bikes. In the general picture on the left, you can see there's a hub motor on the rear wheel (blue), a battery suspended from the frame (red), and a simple handlebar control to make the thing stop and go. In the more detailed cutaway of the hub motor on the right, you can see there's a six-pole magnet in the center (orange) bolted to the frame and an armature (made from coiled wire, yellow) that rotates around it when the current is switched on. It's quite a hefty motor even by modern standards; Ogdon mentions "a heavy current at low voltage—for instance, to carry one hundred amperes at ten volts." So that's 1000 watts, which is about twice the power of a typical modern bike hub motor.
E-bikes are classed according to the power that their electric motor can deliver and the control system, i.e., when and how the power from the motor is applied. Also the classification of e-bikes is complicated as much of the definition is due to legal reasons of what constitutes a bicycle and what constitutes a moped or motorcycle. As such, the classification of these e-bikes varies greatly across countries and local jurisdictions.
To qualify as an electric-assisted bicycle under state law they need to have a seat and fully operable pedals for human propulsion, meet federal motor vehicle safety standards, an electric motor that has a power output of not more than 1,000 watts, maximum speed of not more than 20 mph (electric motor and human power combined), disengages or ceases to function when the vehicle’s brakes are applied, two or three wheels
Historically, women's bicycle frames had a top tube that connected in the middle of the seat tube instead of the top, resulting in a lower standover height at the expense of compromised structural integrity, since this places a strong bending load in the seat tube, and bicycle frame members are typically weak in bending. This design, referred to as a step-through frame or as an open frame, allows the rider to mount and dismount in a dignified way while wearing a skirt or dress. While some women's bicycles continue to use this frame style, there is also a variation, the mixte, which splits the top tube laterally into two thinner top tubes that bypass the seat tube on each side and connect to the rear fork ends. The ease of stepping through is also appreciated by those with limited flexibility or other joint problems. Because of its persistent image as a "women's" bicycle, step-through frames are not common for larger frames.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885.[7][8][9] However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
Since fat tire electric bikes are suitable for a wider variety of situations than a standard cruiser or commuter e-bike, they have the potential to appeal to more people. For example, hunters and campers are ideal candidates for fat tire e-bikes, as they’ll benefit greatly from the heavy-duty tires and powerful motor when they’re navigating difficult wooded trails with lots of gear.
The electric bike revolution is spreading across the continent, 2017 data clearly underlines that eBikes are the preferred mode of mobility. 720,000 eBikes were sold in Germany, and KTM are one of the largest producers in their native country. As the market prospers, more and more manufacturers are jumping on the bandwagon than ever. KTM … Continue reading Best KTM eBikes 2018 – The Fully Charged Picks
Under the doctrine of One Country, Two Systems, Hong Kong has independent traffic law from mainland China. Electric bike are considered as motorcycles in Hong Kong, and therefore needs type approval from the Transport Department as other automobiles. All electric bike availble in Hong Kong fail to meet the type approval requirement, and Transport Department has never granted any type approval for electric bike, making all electric bike effectively illegal in Hong Kong. Even if they got type approved, the driver would need a motorcycle driving license to ride[14]. As a side note, Hong Kong doesn't have a moped vehicle class (and therefore moped driving license), and mopeds are consided as motorcycles too.
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2 [123] as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
Bicycle brakes may be rim brakes, in which friction pads are compressed against the wheel rims; hub brakes, where the mechanism is contained within the wheel hub, or disc brakes, where pads act on a rotor attached to the hub. Most road bicycles use rim brakes, but some use disk brakes.[49] Disc brakes are more common for mountain bikes, tandems and recumbent bicycles than on other types of bicycles, due to their increased power, coupled with an increased weight and complexity.[50]
These small complaints prove that the Rad Wagon isn’t perfect. But its overwhelmingly positive qualities clearly outweigh the drawbacks. The Rad Wagon handled beautifully on city streets, accelerating with ease and maintaining a charge for extended range. Rad Power bikes also offers an array of helpful accessories—think racks, baskets, panniers, and platforms—that make the bike nearly as convenient as a car. Time and time again I passed cars stuck in traffic on their daily commute and couldn’t help but wondering: Why don’t more people switch from cars to an e-bike?
Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles,[77] including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity.[78] A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.[79]
Unrelated to the show but also of local interest. The BC government is soliciting input on what is meant by "active transportation" which could hopefully help to direct policy and regulation governing not just ebikes but all kinds of human scaled transport. If you think electric skateboards should be on their radar or faster S-Pedalec class ebikes then this is a chance to have your voice heard. Electric bicycles have been an entirely grass roots phenomenon for most of their trajectory and it's encouraging to see the entire scope of personal mobility finally being acknowledged and discussed at this level.
Photo: This typical electric bicycle, a Sanyo Eneloop (now discontinued), had a range of about 30–55 km (17–35 miles) and a top speed of around 24 km/h (15 mph). Note the 250-watt hub motor on the front wheel and the 5.7Ah lithium-ion battery pack (black, marked "Sanyo," just in front of the back wheel). Picture by kind permission and courtesy of Richard Masoner, originally published on Flickr under a Creative Commons (CC BY-SA 2.0) licence.
Our hope is that this plug will become to motors in the 500-1500 watt power range what the 9pin Z910 became for the low power geared motors, with all motor manufacturers agreeing to the same pinout standard for easy swapping and interchangeability . We have an L10 version of the Phaserunner motor controller available now and will soon be expanding this to a Grinfineon offering as well.
This 150mm-travel e-mtb tackles big descents, shines on flowy trails, and provides the boost you need for the trip back. Pedal assist comes from Shimano’s 6.2-pound STePS E8000 motor with a 20mph boost. Shifting is motorized too, with Shimano’s exemplary XT Di2 drivetrain providing the most precise and consistent shifts a mountain bike can have. The fun comes from the E-Core’s 150mm of front and rear travel courtesy of a RockShox Yari fork and Deluxe RT shock. Both can be locked out for long, fire-road type climbs, though on an e-bike that feature feels less necessary.
There's no question that electric bikes are far better for the environment than petrol-powered car engines. But that doesn't mean they're completely perfect. Making and disposing of batteries can be very polluting. Not only that, but an electric bicycle is still using energy that has to come from somewhere. You may think you're using clean green power, but the electricity you use for getting about might have come from a filthy old, coal-fired power plant or one driven by nuclear energy. (If you're lucky, of course, it might have come from solar panels or a wind turbine!) Electric bikes are nowhere near as environmentally friendly as ordinary push bikes, but nothing is ever perfect—and, as people often say, "the perfect is the enemy of the good." Electric bikes are certainly a step in the right direction. If everyone used them to get about instead of cars, global warming might be less of a problem, and the world would be a far cleaner and healthier place!
Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
None of this would matter if the VanMoof Electrified S2 (and its close relative the X2) wasn't fun to ride, but it is a blast. Like the Brompton, it pulls off the neat trick of powering you along but giving the illusion that you're doing the work, reacting quickly and cleverly to the speed of your pedalling and the difficulty of any incline you're on. 
In the year 1885, a British man named J.K. Stanley introduced what can fairly be described as the first modern bicycle. His Rover bike had wheels of equal size in the front and back and used a chain connecting the pedals and the rear wheel as a propulsion system. It was often marketed as a safety bike in contrast with the unstable Penny Farthing, and was a smashing success. The company went on to develop motorcycles and automobiles, remaining in business until the year 2005.
My one complaint is the bike’s weight. This sucker is heavy! The aluminum frame looks light, but the the hub motor (4 pounds) and battery (5 pounds) add up. The bike’s total weight is 39 pounds, which is about average for e-bikes but not something you’d want to lug around all day. “This is not a solution for everybody,” Miller admits. “If you live in a fifth floor walkup this is probably not going to work.”
Electric bicycles are considered as "bicycles" under Montana law as the law defines bicycles in a two part definition where the first part of the definition describes a conventional bicycle propelled solely by human power and the second part of the definition describes a bicycle equipped with an independent power source for propulsion in addition to foot pedals to permit muscular propulsion. (Montana Code 61-8-102).[104]
Thanks for your feedback Joe! I personally find black on white to be high contrast and abrasive. Instead, this dark gray scheme is meant to be relaxing… but if it’s uncomfortable to you or difficult to read there are ways to change your browser and even your operating system to be more comfortable using the accessibility options. Here’s a list by device type and for some browsers https://goo.gl/voKTnW hope it helps!
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
Electric motor assisted bicycles have been banned in the State of New York and are not permitted for on-road use.[50][51] It appears the only known allowance of an electric bicycle is if it is an electric powered moped, at this time. There is a proposed bill to allow ebikes. As of May 2009, Bill A2393("Defines the term electric assisted bicycle") has been passed in the NY State Assembly[52] and its corresponding Bill S4014, sponsored by Senator Thomas Morahan, is before the NY State Senate.[53]
My one complaint is the bike’s weight. This sucker is heavy! The aluminum frame looks light, but the the hub motor (4 pounds) and battery (5 pounds) add up. The bike’s total weight is 39 pounds, which is about average for e-bikes but not something you’d want to lug around all day. “This is not a solution for everybody,” Miller admits. “If you live in a fifth floor walkup this is probably not going to work.”
The two most common electric motor styles used in today’s e-bikes are hub motors and mid-drive motors. The Freedom uses a hub motor, which was located in the center of the rear wheel. Hub motors typically don’t offer the same natural maneuverability as the increasingly more common (and more expensive) mid-drive motors because their weight is concentrated in the rear of the bike. It can be jarring when the motor prevents you from going faster than the allotted speed, especially when cruising downhill, but 20 mph is the legal maximum for e-bikes in the US. (In the EU, it’s even lower: 25 km/h, or 15.5 mph.)
You are not allowed to drive S-Pedelecs in France even if they are registered legally in your country (e.g. Germany or Switzerland). In other words, if you plan to take your 45h bike that is legal in your country on vacation in another where it is not, you may violate traffic law. Remove the license plate or don't do it. People who commute between countries, are known to hack removable plates with magnets ...
It is important to note that if a vehicle has an electric motor greater than 500 watts and is capable of powering the vehicle when traveling at a speed greater than 32 km/h and it does not have a CMVSS compliance label it cannot be registered unless the owner can prove, by having the vehicle certified by an engineer, that it is safe for operation on NB highways. Also, not all vehicles are suitable for operation on NB highways and it could be that the vehicle in question may not be a motor driven cycle or a bicycle and cannot be operated on the highway at all.
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
I was hesitant to buy this battery at first due to the minimal amount of review feedback and poor English Grammer in the description. You never know. But, I ended up being very happy with it. Out of all the ebike components I ordered, this battery took the longest by far to get to me, about 11 days to reach me in North Central Florida. However, I believe that's because they ship from China which would also explain the poor grammar in the description. When you think about it, 11 days all the way from China is not bad. Considering the great price and inclusion of the rear rack, it really was worth the wait. I put it on a fat tire mongoose dolomite equipped with a 48v 1000w front hub motor. It was a very heavy bike to begin with, and my thinking was that having the motor in
Photo: Zap Electric's power-assist kit turns a conventional bike into an electric one. There's a bolt-on DC electric motor (weighing just over 3kg or 7lb) just above the back wheel, behind the police officer's foot, pressing against the tire and driving it by simple friction. The motor's powered by a compact lead-acid battery (weighing about 5.5 kg or 12 lb) inside a protective nylon bag. This kit adds quite bit of weight to the bike, but gives extra range and speed when needed. Photo taken in Santa Rosa, California by Rick Tang courtesy of US DOE/NREL.
If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
×