Electric mountain bikes have garnered a lot of attention for their ability to help riders go higher, further, and faster on the trail. As a result, there have been some impressive new eMTB models to hit the market in recent years, making it easier than ever to head off-road. Our favorite is the Haibike SDURO HardNine, which comes equipped with a 350-watt Bosch Performance CX drive and a 500 watt-hour battery. This gives it a range of up to 70 miles, along with a top speed of 20 mph, which is plenty fast on singletrack.
DIY enthusiasts, with tens of thousands of converted bikes using throttle-only, 20+ mph kits, are now officially labeled Moped class. While these bikes handle and pedal-ride just as safely as the class 3 speed pedelecs in many cases, our DIY counterparts will be officially kicked out and left on their own for advocacy and legal acceptance in California. This is a big deal, without a class sticker, any DIY electric bike conversion kit is considered a Moped and not a bicycle.
We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2 [123] as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
Did you know that electric bikes can be used for fitness training? Or that they have been scientifically proven to increase the amount of cycling people do? Or that they have proven health and fitness benefits? Well, it’s all true! Apart from being tons of fun, ebikes can be used to improve health and fitness in many ways. Here are our top posts about how ebikes can improve your health and fitness.
Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).

To legally operate a motorized bicycle or electric-assisted bicycle the operator must be licensed, the motorized bicycle/electric-assisted bicycle must be registered in one of the following definitions and meet the required safety equipment. If the operator or the motorized bicycle/electric- assisted bicycle does not meet all requirements, they will not be legal for street/highway use (including the sidewalk).To qualify as a motorized bicycle under state law they need to have motor of a piston displacement capacity of 50 cubic centimeters or less, maximum of two brake horsepower, maximum speed of not more than Template:Convert on a flat surface, fully operable pedals for human propulsion are not required, but may be a part of the machine.


Motor-driven cycles may be operated on the roadway without registration, but the operator must have a driver's license.[85] The cycle may not be operated on any sidewalk, limited access highway or turnpike. If the maximum speed of the cycle is less than the speed limit of the road, the cycle must operate in the right hand lane available for traffic or upon a usable shoulder on the right side of the road unless the operator is making a left turn.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
The first functioning electric motor was displayed in the early 19th century, though the device constructed by British scientist Michael Faraday did little more than swirl a wire around a magnet when an electric charge was introduced. Still, the concept proved that electricity could do work. Functional electric motors would follow in many forms after that achievement in 1821. Soon scientists and tinkerers around the world, including visionaries such as Nikola Tesla, were experimenting with all manner of electric motors -- some worked with DC power, others with AC. By the end of the century, myriad electric motors had been produced, capable of exerting enough force with enough reliable control that they were practical for use in myriad applications.

Nebraska defines a Moped as "a bicycle with fully operative pedals for propulsion by human power, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters which produces no more than two brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than thirty miles per hour on level ground."[69]
E-bikes use rechargeable batteries, electric motors and some form of control. Battery systems in use include sealed lead-acid (SLA), nickel-cadmium (NiCad), nickel-metal hydride (NiMH) or lithium-ion polymer (Li-ion). Batteries vary according to the voltage, total charge capacity (amp hours), weight, the number of charging cycles before performance degrades, and ability to handle over-voltage charging conditions. The energy costs of operating e-bikes are small, but there can be considerable battery replacement costs. The lifespan of a battery pack varies depending on the type of usage. Shallow discharge/recharge cycles will help extend the overall battery life.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
If you're more concerned with conquering the countryside than the commute, Cyclotricity's Stealth is the one for you. It's a full-size mountain bike, with aggressive tyres and suspension on the front forks to absorb the rocks and bumps on the trails. It's comfortable to ride, and its motor can either give you assistance while you ride, or you can just hit the throttle to rocket over hills with no effort on your part.
It's a solid e-bike, but it's also very heavy one for a folding bike. I found it difficult carry when the bike is folded as the carrying handle is useless, and the center of gravity is towards to the rear wheel so one has to find a place in the rear of the bike to pick it up. Even when the bike is folded, it's bulky and heavy, It's difficult to walk with it while carrying it. It's easy to hurt one's back if he or she is not careful. I would not recommend carrying this bike up or down stairways.
This slick-looking commuter features a clean and quiet Gates Carbon Drive belt, which eliminates the maintenance that comes with a derailleur, and an internally geared Enviolo Trekking hub, which provides a 380 percent gear range. The Embark has 650b wheels, 47mm WTB gumwall tires, full fenders with mudflaps, and integrated lights—meaning you can ride long after the sun sets—or before it rises. A Bosch Active Line Plus mid-drive motor is light and quiet and provides pedal assist up to 20 mph, and the Bosch 400Wh battery has a claimed range of 50 miles. Everything about the Embark frame screams clean, stylish, and organic.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.
Can I legally buy/build and ride an ebike that’s faster than 20 mph? Yes you can, but you need to know that the ebike is no longer considered equivalent to a bicycle and is subject to other state vehicular classifications. The definitions for electric bikes spanning 20-30mph, and 1-2 horsepower ranges, will vary from state to state, resulting in a no-man’s-land consensus about limits for motor vehicle definition. The common label for a 20-30mph, 2-wheeled vehicle with active pedals is a Moped. Other MVA labels include motor scooter, motorbike and dirt bike which may have equivalent power and speed performance, but do not have pedals to assist and move the vehicle.
Built by a company that’s made cycling equipment for more than four decades, the Vado feels more like a traditional bicycle than almost any other ebike. Its frame and components have been tuned to provide a familiar experience, making it easy for new and long-time cyclists to jump on and start pedaling. Specialized’s heritage shines through nicely, helping separate itself from the competition in an increasingly crowded ebike market.
When last checked, no E-bikes satisfied this requirement, so ebikes cannot be registered in New Jersey.[108] However, NJ Bill A2581, introduced March 22, 2010, would permit the use of low-speed electric bicycles upon the roadways and bicycle paths in NJ, where a low-speed electric bicycle is defined as a two-wheeled vehicle with fully operable pedals for human propulsion and an electric motor of less than 100 pounds and 750 watts, whose maximum speed on a paved level surface is less than 20 miles per hour.[109] The bill has been referred to the state's Assembly Transportation, Public Works and Independent Authorities Committee.[110]
A local unit of government having jurisdiction over a road or bikeway (including the Department of Natural Resources in the case of state bike trails) is authorized to restrict e-bike use if: the use is not consistent with the safety or general welfare of others; or the restriction is necessary to meet the terms of any legal agreements concerning the land on which a bikeway has been established.
But the good times of the stealthy ebike existence will not endure forever. The ebike market is growing steadily and more so, technology is driving performance up and costs down. The market for a green, lifestyle friendly, transportation technology, with GPS, theft ID, cell service and probably skim lattes is alive and driving an emerging market. It is a matter of time before we all must face and respond to the legal demands of the state and local laws. Not to be over obligatory about being legal and duty oriented, but I do call on my fellow ebikers to ride legal, whether ebike, moped or other. Go ahead and build the 1200W ebike of your dreams, but get it insured and licensed if you must. Such compliance will set the precedence for public acceptance of ebikes in general, and build a track record for expansion and mainstreaming of moped-speed ebikes for commuter value driven needs of the future.
What exactly is an electric bike? How can they be used for transportation and why do they make financial sense? These are some of the questions my site http://electricbikereview.com and this channel aim to help you answer. This particular video provides an overview of the Easy Motion Neo Jumper ebike and then follows me on an actual commute to work in Austin Texas.

It’s a topic that many eMTBers are interested in: fast charging. What has long been a reality with electric cars is now also being partly improved for ebikes with high amperage chargers. Bosch has presented a 6A charger this year that can charge a 500 Wh battery in 3 hours, more than a third faster than the standard charger. The new benchmark next year, however, will probably be the 10A charger presented by Haibike and BMZ. It is claimed to be capable of charging a 630 Wh battery in just 1.5 hours.


During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.


Controllers for brushed motors: Brushed motors are also used in e-bikes but are becoming less common due to their intrinsic lower efficiency. Controllers for brushed motors however are much simpler and cheaper due to the fact they don't require hall sensor feedback and are typically designed to be open-loop controllers. Some controllers can handle multiple voltages.
There are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia.[5]

What we especially love is how quiet this e bicycle is. If you’re riding down the street or through the park, the gentle hum of the motor is unnoticeable. This is because it’s hidden by the sound of your smooth pedaling. If you’re not into flashy gadgets, any ordinary person would assume you’re riding a conventional peddle bike. This is a great commuter bike.

I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have
We need to support and put our purchasing power behind ebikes sold in the U.S. that are trying to comply with the California rules which allow 500w and 750w nominal motors and establish 3 classes. If these bikes can create a big enough footprint in the market then future U.S. bike rules may universally adopt these standards. It is better than engaging in regulation showdowns without any standardized and unified proposal on the part of the Electric Bike Community.
Visually, the Pedego City Commuter Classic Electric Bike is stunning – a smart blend of yesteryear's style and today's technology. Pleasantly high handlebars, a sprung seat, and lovely Schwalbe Fat Frank tires make it very comfortable. Stopping is taken care of by powerful disk brakes, front and rear. Lights are included, as is a useful cargo rack. From an e-bike standpoint, the Pedego Classic City Commuter sports a reliable, hub-mounted motor driven by a 36-volt, 10-amp battery. There's a digital display with a trip computer, odometer, speedometer, pedal assist level, and battery charge information.
Rear-Mounted Hub Motor, installed on the rear wheel, are more common on pre-built bikes because they’re easily installed at the factory. For a conversion, it’s a little harder to install than a front hub motor because of the chain, gearing and derailleur. Plus, you may be limited to a 6 or 7-speed freewheel. However, rear wheel drive will provide more torque and is less noticeable than a front hub.
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]

Uniparts eyeing overseas acquisition to expand hydraulic cylinder biz / Maruti Suzuki launches new Alto with BS VI engine; price starts at Rs 2.93 lakh / Top 10 selling two-wheelers in FY19: Honda Activa retains the top spot / KPIT Tech back on exchanges, scrip races to ₹105 / Maruti Suzuki doubles market share in LCV goods carrier segment in FY'19 / Mercedes-Benz partners the first-ever international esport competition ‘ESL One’ in India / Audi opens service facility in Vijayawada / KPIT Technologies gets listed on BSE and NSE / Honda launches new CBR650R at Rs 7.7 lakh / Hiroshi Ii joins JTEKT India as new chairman


"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Title 7, Chapter 551 entitled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D.[131] Under Chapter 541.201 (24), "Electric bicycle" means a bicycle that is (A) designed to be propelled by an electric motor, exclusively or in combination with the application of human power, (B) cannot attain a speed of more than 20 miles per hour without the application of human power, and (C) does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle on a highway[132] that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle on a highway used primarily by pedestrians.
"Motor-driven cycle" means any vehicle equipped with two or three wheels, a power source providing up to a maximum of two brake horsepower and having a maximum piston or rotor displacement of 50 cubic centimeters if a combustion engine is used, which will propel the vehicle, unassisted, at a speed not to exceed 30 miles per hour on a level road surface, which does not require clutching or shifting by the operator.[138] The designation is a replacement for "scooter" and "moped;"[139] Vermont doesn't seem to have laws specifically for e-bikes.[140]
Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
The other motor is the G311, a front equivalent to the wonderfully silent G310 rear motors we introduced late last year. This motor will be replacing the G01 hub for our front mini geared kits. It's a tad lighter (2.3kg), much quieter (spiral gears!), but still has the features from the G01 that we loved. That means a side cable exit, ISO disk rotor compatibility, and 10mm round axle.
How do the State Laws relate to the 2001 Federal Law? This is a difficult question to answer and know how they apply to you individually. From the Federal Law, one would hope that your purchased ebike is simply classified as a bicycle, with all the rights and privileges allotted to a normal cyclist. However, State Laws are confusing because they may be more restrictive in parts and add other requirements. About 30 U.S. states still have confusing regulations around them. Either the bikes are technically classified as mopeds or motor vehicles, or they have equipment, licensing or registration requirements that cause problems for riders. Thanks to the People-For-Bikes/Bicycle Product Suppliers Association (BPSA) partnership with local advocacy groups, they have been able to make the case for streamlining state regulations so that e-bikes are essentially treated like regular bicycles.4
The Super Commuter is very aptly named. The 350w Bosch motor will help you sustain speeds of up to 28mph, and the burly, 2.4-inch wide, Schwalbe Super Moto-X 650b tires will keep you secure on even the roughest city streets, and Shimano Deore hydraulic brakes provide ample stopping power. Fenders provide welcome protection from road spray so you arrive at your destination fresh, integrated lights are critical for post-sunset riding, and a side-view mirror hanging on the left side of the handlebar gives a great view of traffic around you. After all, you can ride at the speed of urban traffic on the Super Commuter.
The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations.[63] The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.
×