Bicycle brakes may be rim brakes, in which friction pads are compressed against the wheel rims; hub brakes, where the mechanism is contained within the wheel hub, or disc brakes, where pads act on a rotor attached to the hub. Most road bicycles use rim brakes, but some use disk brakes. Disc brakes are more common for mountain bikes, tandems and recumbent bicycles than on other types of bicycles, due to their increased power, coupled with an increased weight and complexity.
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.
"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,  written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
Like most electric bikes, the Rad Wagon is also fairly heavy, weighing 72 pounds. The last drawback is that it comes in only one frame size (which I imagine helps to keep costs lower) that fits rider heights between 5 foot 2 inches and 6 foot 2 inches. My 6 foot 4 husband, however, can ride the bike just fine, so there’s some wiggle room to this range.
I would add that the point of the article seems to encourage ebikers to “know the state laws” and be confident within those boundaries. To D McCarthy’s question, if your state has a definition for ebikes and classifies them as bicycles and affords access as bicycles, AND, your particular ebike is built within those specifications, then you should be able to ride that section of road with confidence. Just my 2C.
Most consumers want an e-bike that will accommodate its motor without being too cumbersome and will remain stable in spite of its electronic components. Some consumers want only the most basic of e-bike features, including lights, a cargo rack/basket, and a water bottle holder. Others are focused more heavily on safety features, such as brake type. And still others are concerned with convenience and portability.
What we especially love is how quiet this e bicycle is. If you’re riding down the street or through the park, the gentle hum of the motor is unnoticeable. This is because it’s hidden by the sound of your smooth pedaling. If you’re not into flashy gadgets, any ordinary person would assume you’re riding a conventional peddle bike. This is a great commuter bike.
Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).
Different gears and ranges of gears are appropriate for different people and styles of cycling. Multi-speed bicycles allow gear selection to suit the circumstances: a cyclist could use a high gear when cycling downhill, a medium gear when cycling on a flat road, and a low gear when cycling uphill. In a lower gear every turn of the pedals leads to fewer rotations of the rear wheel. This allows the energy required to move the same distance to be distributed over more pedal turns, reducing fatigue when riding uphill, with a heavy load, or against strong winds. A higher gear allows a cyclist to make fewer pedal turns to maintain a given speed, but with more effort per turn of the pedals.
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.
Conversion kits, on the other hand, are sold and installed separately on traditional bicycles. They are harder to setup and conceal, and require some basic mechanical ability and a little bit of ‘elbow grease’ to install. The advantage of conversion kits is that you can choose almost any standard bicycle, and you have the freedom to change or upgrade components as you go. A conversion kit will also allow you to achieve higher power and speed ratings that are not possible on most pre-built electric bike models. Kits are great for tall or heavy riders because they can opt for a larger bike, with higher power and weight carrying capacity. People living in hilly terrain may require the additional torque to handle extremely large inclines. For people who prefer a specific bike model or just love to go faster, a conversion kit offers enormous flexibility.
For people wanting to push the effects of Statorade to the max, the Australian made Hubsinks can clamp on to your motor shell and provide additional cooling fins to shed heat to ambient air. These fit our new MXUS Cassette motors, and the 9C, Crystalyte H, and many others. These are listed on our new store category for motor cooling mods. And like other small products, we try to keep a stock of 10mL Statorade syringes on Amazon for easy shipping to US customers. They are sold out now but another shipment is inbound.
DIY enthusiasts, with tens of thousands of converted bikes using throttle-only, 20+ mph kits, are now officially labeled Moped class. While these bikes handle and pedal-ride just as safely as the class 3 speed pedelecs in many cases, our DIY counterparts will be officially kicked out and left on their own for advocacy and legal acceptance in California. This is a big deal, without a class sticker, any DIY electric bike conversion kit is considered a Moped and not a bicycle.
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour Helmets are required.
If you're taking your bike inside, consider one that folds up. The Cyclotricity Wallet has a motor in the front wheel, which takes you up to speed either by assisting your pedalling, or you can sit back and use the throttle by itself. Its folding design makes it slightly easier to get in and out of a building, but its hefty weight means you still won't find it easy to carry onto public transport.
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.
A KS LEV Integra dropper post, 130mm of front and rear travel, 27.5-inch wheels, and trail-grabbing 2.8-inch tires make this pedal-assist mountain bike a great option if you want to climb farther to shred longer, but don’t want to lug your bike uphill for ages. The 250-watt motor, placed slightly farther forward than most other bikes to optimize weight distribution and handling, provides a nice boost so you can enjoy the ride up and not be too gassed when you get to the top.
Range is a key consideration with electric bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. The range of an electric bike is usually stated as somewhere between 7 km (uphill on electric power only) to 70 km (minimum assistance) and is highly dependent on whether or not the bike is tested on flat roads or hills. Some manufacturers, such as the Canadian BionX or American E+ (manufactured by Electric Motion Systems), have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging. This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS.
The Bulls Cross E8 Step-Thru is an urban bike—a bicycle often used as a primary mode of transportation for those who choose not to own a car. Priced at $3,099, it's solid and durable. The aluminum frame comes in three sizes (45cm, 50cm, and 53cm; I tested the latter). It's got an eight-speed Shimano shifter and a Shimano Deore CS-HG50 cassette. Shimano is a small change for me, as my XO2 uses the SRAM Rival Double Tap shifter, and I really like the action on that. It's got a front suspension with 63mm of travel for a smoother ride, along with Shimano hydraulic disc brakes. Cable runs are all internal, making for a cleaner-looking profile. Rack, fenders, and a headlight all come standard.
It’s unlikely the Instagram generation ever thought there would be an eBike built with them in mind. Stereotypes of old people riding their e-assisted bikes with cumbersome batteries and questionable frames. Then Lithium Cycles and the Super 73 turned up! Across the last few months, social media has been bustling with talk, influencers, Will Smith … Continue reading Lithium Cycles Super 73: Coming Soon
As often preached, eBikes are arguably the most efficient, enjoyable and clean way to travel around the city. Here at Fully Charged, we have an eBike for all, from the eMTBs, to folding electric bikes. But certainly our most popular are urban commuter eBikes. For those bored of playing sardines on the tube, or taking … Continue reading Commuter eBike riding: The Fully Charged Picks
The Netherlands has a fleet of 18 million bicycles. E-bikes have reached a market share of 10% by 2009, as e-bikes sales quadrupled from 40,000 units to 153,000 between 2006 and 2009, and the electric-powered models represented 25% of the total bicycle sales revenue in that year. By early 2010 one in every eight bicycles sold in the country is electric-powered despite the fact that on average an e-bike is three times more expensive than a regular bicycle.
There are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia.
Battery-electric locomotive Battery electric vehicle Cater MetroTrolley Electric aircraft Electric bicycle Pedelec Electric boat Electric bus Battery electric bus Electric car List Electric truck Electric platform truck Electric vehicle Electric motorcycles and scooters Electric kick scooter Gyro flywheel locomotive Hybrid electric vehicle Hybrid train Motorized bicycle Neighborhood Electric Vehicle Plug-in electric vehicle List Plug-in hybrid electric vehicle Solar vehicle Solar car Solar bus
This article did a good job of trying to justify the assist speed limits but fell short of detailing how that can ever be effectively enforced. In reality the only enforcement that is going to work is applied speed limits to use of bikes and ebikes. For example, it makes sense that a bike lane on a street that the speed limit of vehicles is the speed limit of the bikes/ebikes. On sidewalks and shared pedestrian paths the speed limit probably does need to be in the 15-20mph range to match traditional bikes speeds on those paths.
European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.
Both bikes have passable cadence sensor pedal assist that kicks in a little late and lets go a little early. Torque sensors are too expensive for this price level so you are just not going to get the same responsiveness as a bike store e-bike. Rattan has 5 levels of pedal assist while the Ancheer has 3. Over long periods of pedaling the PAS evens out or you can just use the throttle.
In most jurisdictions, bicycles must have functioning front and rear lights when ridden after dark. As some generator or dynamo-driven lamps only operate while moving, rear reflectors are frequently also mandatory. Since a moving bicycle makes little noise, some countries insist that bicycles have a warning bell for use when approaching pedestrians, equestrians, and other cyclists, though sometimes a car horn can be used when a 12 volt battery is available.
The Super Commuter is very aptly named. The 350w Bosch motor will help you sustain speeds of up to 28mph, and the burly, 2.4-inch wide, Schwalbe Super Moto-X 650b tires will keep you secure on even the roughest city streets, and Shimano Deore hydraulic brakes provide ample stopping power. Fenders provide welcome protection from road spray so you arrive at your destination fresh, integrated lights are critical for post-sunset riding, and a side-view mirror hanging on the left side of the handlebar gives a great view of traffic around you. After all, you can ride at the speed of urban traffic on the Super Commuter.
The aluminum, step-through eJoy is the happy medium between traditional-looking townies that don’t transport much more than the rider and often cumbersome cargo models that are sometimes a challenge to store. With 26-inch wheels, full fenders, a Shimano Alivio nine-speed drivetrain and disc brakes, a wheelbase similar to the average townie, and a big, comfy seat, it has the appearance of a practical everyday cruiser. But its oversize rear rack, silent Bosch Active Line motor, heavy-duty head tube with front-tray mounts (the tray is an add-on), integrated Supernova E3 lights, and roll-over-anything balloon tires hurtle it into hmm-this-could-actually-replace-my-car status. It’s one of the quietest, most convenient, most stylish, and easiest-to-operate e-bikes available.
A human traveling on a bicycle at low to medium speeds of around 16–24 km/h (10–15 mph) uses only the power required to walk. Air drag, which is proportional to the square of speed, requires dramatically higher power outputs as speeds increase. If the rider is sitting upright, the rider's body creates about 75% of the total drag of the bicycle/rider combination. Drag can be reduced by seating the rider in a more aerodynamically streamlined position. Drag can also be reduced by covering the bicycle with an aerodynamic fairing. The fastest recorded unpaced speed on a flat surface is 144.18 km/h (89.59 mph)
Bike is awesome, warranty support has so far delivered, but is a hassle to deal with (and hassle is acceptable and better than nightmare, or unresponsive/clueless/unhelpful/not-english-speaking). To be fair, this is the middle of Swag's busy season. Check tire inflation, check and tighten fasteners, seatpost and handlebars and stem out of the box, RTFM, charge the battery and you're out the door riding quickly.
With a 150mm-travel RockShox Yari fork and 132mm of rear travel from the RockShox Monarch Plus R shock, the Remote CTRL is Kona’s first dual-suspension e-mountain bike. It’s powered by a 250-watt Bosch Performance Line XC mid-drive motor that uses the company’s progressive E-MTB mode that is adaptable to rider input, which means you don’t have to toggle through assistance modes while riding. It offers assistance up to 20 mph, and the 500Wh integrated battery is the largest Bosch currently offers. Beefy 27.5x2.8-inch Maxxis Recon tires offer plenty of traction and also help to absorb smaller hits.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h). An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.. The legislation enacting this amendment to the CPSC is also known as HR 727.
Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.
Electric bikes (also known as e bikes) are perfect for long-distance riding, or when you just don’t feel like giving your full effort. What differentiates them from electric motorcycles is the ability for the rider to pedal the bike at any time, so if you’re riding along and your battery dies, you’re not going to stranded. These are often very valuable bikes, but some models can be more affordable than you might expect, especially when you treat them as a form of transportation as opposed to thinking of the price in terms of regular bicycles.
Electric bikes are a green alternative to driving a vehicle. Studies carried out in several towns and cities show that the average car speed in rush hour traffic can dip as low as 18 to 20 mph. Electric bike speed can be as high as 15 mph. With an electric bike, you can reduce pollution, improve fitness, and still arrive at the same time as your car-bound colleagues.
There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.
Whether squeezing onto the 4 train or pedaling through Lower Manhattan, I notice a few curious glances at the bike with the big battery in the center of the frame. This is not surprising; e-bikes are huge practically everywhere but the US. According to the latest figures from the Confederation of the European Bicycle Industry, e-bike growth in the UK is up from 40,000 units in 2016 to 63,000 in 2017.
Electric mountain bikes have garnered a lot of attention for their ability to help riders go higher, further, and faster on the trail. As a result, there have been some impressive new eMTB models to hit the market in recent years, making it easier than ever to head off-road. Our favorite is the Haibike SDURO HardNine, which comes equipped with a 350-watt Bosch Performance CX drive and a 500 watt-hour battery. This gives it a range of up to 70 miles, along with a top speed of 20 mph, which is plenty fast on singletrack.
During nighttime operation, the bicycle must be equipped with a front headlamp, a rear-facing red reflector, and reflectors on the front and rear of pedals, and the bicycle or rider must have reflective surfaces on each side. Minn. Stat. §169.222, subd. 6. An electric-assisted bicycle can be equipped with a front-facing headlamp that emits a flashing white light, a rear-facing lamp that has a flashing red light, or both. The bicycle can carry studded tires designed for traction (such as in snowy or icy conditions).
Powered by a 250-watt Brose Centerdrive system, the Redux is capable of reaching speeds of up to 28 mph, which comes in handy when dodging traffic. The lithium-ion battery provides enough juice to give the bike a range of up to 80 miles between recharges, making it a great option for daily commuters. Raleigh even outfitted the bike with wide tires which provide stability and traction, even when the road gets wet. Other key features include a 10-speed Shimano crankset and shifters and a built-in LCD screen that displays all the usual information.
Cargo bikes and city bikes are common in the e-bike space, but until recently we haven’t seen that many performance road bikes. The Giant Road E+1 is a pedal-assist performance road bike that’s made for more than just commuting; the powerful motor can crank you up to 28 mph very quickly on the highest setting so you can rip the flats, join your local group ride, or blast through the mountains with far less effort than a traditional road bike. It won’t feel like a 16-pound race bike when you lean it into high-speed turns, but the endurance-oriented geometry allows for an aggressive position on the bike and keeps it nimble and agile at high speed.
Some of the Rad Wagon’s (small) flaws became apparent once I added more weight to the bike. The integrated rear rack can attach various panniers, platforms, or baskets to cary your cargo, but I was most concerned with hauling my two kiddos to school. Riding the bike with my three year old was a cinch; he held on to the bars in the caboose (available as an accessory add-on) and enjoyed the view. Adding my very tall, almost seven-year-old daughter, however, was a bit more complicated.
And let’s not forget the economic advantages of owning an e-bike. The annual cost of running a new family car is, on average, about $9,000 per year. Running an electric bike costs around $400 per year. And while filling a gas tank costs around $30, recharging an electric bike battery costs only about 50 cents. A tank of gas may get you further, but not 60 times further!
Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.
There are dozens of good 25Km/h pedelecs. Our advice is to go the nearest good e-bike store and get it from there, because e-bikes may need good support. Only if you like servicing a bike yourself is buying from the Internet a good option. As of Spring 2013, a good benchmark to compare with is the Austrian KTM Amparo also called KTM Severo 8M or the German Kalkhoff Impuls or Agattu series. It has a reliable Panasonic middle motor and a good battery. If you want a more sexy design, try the SMART from the urban car maker of the same name.
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.
I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead.
E-bikes mostly use motors and battery options from a few major suppliers: Bosch, Yamaha, Shimano, and Brose. A few other brands exist, but are less reliable or powerful. Some, like the Yamaha system, have more torque, and others, like Bosch’s Active Line, are nearly silent. But, generally, all four make good options. Look for motor output (in torque), which will give you an idea of total power. Just like car engines, more torque equals more power off the line and more boost to your pedaling. But watt hours (Wh) is perhaps a more important figure to use—it takes into account battery output and life to give a more accurate reflection of power (higher Wh equals bigger range).
Flyer Vollblut. A new rear motor bike from one of the most reliable E-bike makers. This model doesn't look as "heavy" as most other Flyer models. The Vollblut 500 has the 500W new Panasonic rear motor, front fork suspension, 28 inch wheels. It is in the same price range as the Stöckli and the Stromer. Flyer is known for top service and reliability, but it's a new model with a new motor ....
Despite the illegal status in the state of New York, enforcement of this law varies at the local level. New York City enforces the bike ban with fines and vehicle confiscation for throttle activated electric bikes. However, Mayor Bill de Blasio has recently changed the city's official policy to legalize pedal-assist electric bikes that have a maximum speed limited to 20 mph.  Contrarily, Tompkins County supports electric bike usage, even providing grant money to fund electric bike share/rental projects.
The electric bike revolution is spreading across the continent, 2017 data clearly underlines that eBikes are the preferred mode of mobility. 720,000 eBikes were sold in Germany, and KTM are one of the largest producers in their native country. As the market prospers, more and more manufacturers are jumping on the bandwagon than ever. KTM … Continue reading Best KTM eBikes 2018 – The Fully Charged Picks
More powerful pedelecs which are not legally classed as bicycles are dubbed S-Pedelecs (short for Schnell-Pedelecs, i.e. Speedy-Pedelecs) in Germany. These have a motor more powerful than 250 watts and less limited, or unlimited, pedal-assist, i.e. the motor does not stop assisting the rider once 25 km/h has been reached. S-Pedelec class e-bikes are therefore usually classified as mopeds or motorcycles rather than as bicycles and therefore may (depending on the jurisdiction) need to be registered and insured, the rider may need some sort of driver's license (either car or motorcycle) and motorcycle helmets may have to be worn. In the United States, many states have adopted S-Pedelecs into the Class 3 category. Class 3 ebikes are limited to <=750 watts of power and 28 mph.
Some power-on-demand only e-bikes can hardly be confused with, let alone categorised as, bicycles. For example, the Noped is a term used by the Ministry of Transportation of Ontario for e-bikes which do not have pedals or in which the pedals have been removed from their motorised bicycle. These are better categorised as electric mopeds or electric motorcycles.
I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have
Awesome little machine. My wife loves it. She gets so many people asking her where she got it and that they want one too. I have an 6 speed/ electric bike but she is not comfortable riding it or any bike for that matter but she’s totally comfortable and confident when she rides the swag. Great product. Exceptional quality and cool looking too. You can’t go wrong with this machine for your wife or daughter or whomever wants to ride but doesn’t want anything bulky or to heavy.
However, Emu sells a little foldable number if that's your bag. The Emu Crossbar is for town commuters that require a sweet ride that's backed up by solid Shimano Nexus hub gears and Tektro brakes, which are adequate if not the best on the market. Riding is smooth and easy, with the crank moving sensor doing its best to iron out any gaps in power delivery.