Earlier UK regulations required that the motor has an average power output limited to 200 W (250 W for tricycles and tandems) and weight limited to 40 kg (60 kg for tricycles and tandems). These regulations must come in-line with the EU regulations by (find deadline). For models sold before June 2003, e-bikes conforming to the speed, weight and power limits may also be considered pedal cycles. Electric bikes with higher power outputs, or those not meeting the "pedelec" definition are now treated as motorcycles and require a license.

As electric bike options continue to expand, more brands are integrating the battery more seamlessly. That makes them look sleeker (and more like a real bike). Batteries are expensive, so make sure there’s a good way to lock the battery to your bike if you’ll be keeping it outside. Overall weight is important. Some battery and motors can add 15 pounds or more to the bike. With assist, you won’t feel that much when you’re riding, but you will if you have to carry your bike up stairs or lift it onto a bike rack.


Riding a pedal-assisted road bike may seem counterintuitive but during longer training sessions, the minimal addition of power helps prevent overall muscle fatigue and injury. Similarly, those looking to enjoy longer scenic routes will appreciate the general boost an electric drive provides. With a top speed of 28 mph, the Road E+1 uses three power modes to give you ultimate control over your ride and assistance level. A four-point sensory system monitors the pedaling force allowing the motor to amplify your movements seamlessly.

The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
The Class 3 Aventon Pace 500 urban e-bike has five levels of pedal assist and tops out at 28 mph. But the Pace has something not found on a lot of modern e-bikes. In addition to pedal power, it also has a throttle—in the case of the Pace, a small thumb paddle on the left side of the handlebar next to the control unit that holds at a steady 20 mph, no pedaling required. The bike itself has an aluminum frame, a swept-back handlebar, ergo grips, a sturdy kickstand, hydraulic disc brakes, 8-speed Shimano Altus shifting and gearing, 27.5x2.2-inch Kenda e-bike-rated tires, a saddle the size of Texas, and good ol’ classic city/commuter-bike geometry. It doesn’t come equipped with fenders or a rear rack, but you can add them. Power comes in the form of a 500-watt rear-hub motor, a semi-integrated battery on the down tube (with a range of up to 50 miles), and a backlit display unit mounted on the stem.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
Justin and Anne-Sophie have been on the road in Europe for about a week now, catching as much sun as they can on the Suntrip. Since the start of the trip in Lyon and the official start of the race in Chamonix, they have been trending on a more southerly route towards Turkey and Iran. As they get used to the style of travel and the nuances of riding a three-wheeled solar vehicle all day they have had their ups...
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
Toe-clips and toestraps and clipless pedals help keep the foot locked in the proper pedal position and enable cyclists to pull and push the pedals. Technical accessories include cyclocomputers for measuring speed, distance, heart rate, GPS data etc. Other accessories include lights, reflectors, mirrors, racks, trailers, bags, water bottles and cages, and bell.[52] Bicycle lights, reflectors, and helmets are required by law in some geographic regions depending on the legal code. It is more common to see bicycles with bottle generators, dynamos, lights, fenders, racks and bells in Europe. Bicyclists also have specialized form fitting and high visibility clothing.
The BC Bike Show is the premier cycling and outdoors event in Western Canada and is happening in just 2 weeks on March 2nd and 3rd. We'll be there of course, and in addition to our exhibitor booth we'll also be hosting Cycle Stage to give more public presentations. On Saturday at 11:45 am we'll talk on how to navigate the various motor and battery options available for ebike retrofits, and on Sunday at 2pm we'll be doing a live demonstration of a regular bicycle being converted over to electric assist.
At first glance, Wing’s e-bikes share some design features with Dutch e-bike company VanMoof’s flagship bikes, most noticeably the elongated top tube (23.3 inches) with embedded front and rear lights. There are differences — VanMoof’s battery is embedded in the frame, while Wing’s is external — but to look at them side-by-side, one could easily conclude that Wing is just a less-expensive version of the VanMoof.

In general, U.S. and European cycle manufacturers used to assemble cycles from their own frames and components made by other companies, although very large companies (such as Raleigh) used to make almost every part of a bicycle (including bottom brackets, axles, etc.) In recent years, those bicycle makers have greatly changed their methods of production. Now, almost none of them produce their own frames.
This is an unofficial guide to the laws governing electric bicycles in the United States as of 2016. It was contributed by a guest writer The Smart Ped`aleck who was paid and remains unaffiliated with any electric bicycle company. It may be updated ongoing and is cited throughout with reference links and attributions at the end. It is designed to be an entertaining starting point for understanding the space, digging deeper and in turn choosing the best electric bike platform for your needs.
My one complaint is the bike’s weight. This sucker is heavy! The aluminum frame looks light, but the the hub motor (4 pounds) and battery (5 pounds) add up. The bike’s total weight is 39 pounds, which is about average for e-bikes but not something you’d want to lug around all day. “This is not a solution for everybody,” Miller admits. “If you live in a fifth floor walkup this is probably not going to work.”
We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.
If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
In summary, federal law trumps all States’ laws. That is true with bicycle law, too. States cannot constitutionally pass legislation that reduces or eliminates Federal laws, they can only pass legislation that enacts additional (tighter) restrictions on its people. States can’t define an ebike a bicycle if greater than 750W/20mph, nor can they define an ebike a motor vehicle if less than the Federal Government’s limit of 750 Watts and a top electric-powered speed of 20 MPH.3This is the Federal definition of a low speed electric bike, which equates it to a bicycle.
In China, which has the highest number of electric bicycles in the world, electric bikes currently come under the same classification as bicycles and hence don't require a driver's license to operate. Previously it was required that users registered their bike in order to be recovered if stolen, although this has recently been abolished. Due to a recent rise in electric-bicycle-related accidents, caused mostly by inexperienced riders who ride on the wrong side of the road, run red lights, don't use headlights at night etc, the Chinese government plans to change the legal status of illegal bicycles so that vehicles with an unladen weight of 20 kg or more and a top speed of 30kmh or more will require a motorcycle license to operate, while vehicles lighter than 20 kg and slower than 30kmh can be ridden unlicensed. In the southern Chinese cities of Guangzhou, Dongguan and Shenzhen, electric bicycles, like all motorcycles, are banned from certain downtown districts. There are also bans in place in small areas of Shanghai, Hangzhou and Beijing.
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[43][44] Helmets are required.
Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3 wheeled bicycle (sic.: 3 wheeled bicycle) that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Federal Motor Vehicle Safety Standards for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1-5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for both. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities. [13]

However, Emu sells a little foldable number if that's your bag. The Emu Crossbar is for  town commuters that require a sweet ride that's backed up by solid Shimano Nexus hub gears and Tektro brakes, which are adequate if not the best on the market. Riding is smooth and easy, with the crank moving sensor doing its best to iron out any gaps in power delivery.
While the first functional battery was developed in the year 1800 by Italian physicist Alessandro Volta, a practical battery would not be seen for several decades yet. By the end of the 19th century, practical and portable batteries were more widely available, this finally freeing the electric motor to be used in a wide new array of applications. It might come as a surprise, but the electric motor, battery, and a bicycle were first paired as far back as the 1890s. It would be approximately 100 years later that electric bicycle development finally entered the mainstream, but the technology and concept behind the electric bike were all in place generations ago.
Generally they are considered vehicles (like motorcycles and pedal cycles), so are subject to the same rules of the road. Regulations may define maximum power output and for electric bikes may or may not require an interlock to prevent use of power when the rider is not pedaling. In some cases regulatory requirements have been complicated by lobbying in respect of the Segway HT.
The handlebars connect to the stem that connects to the fork that connects to the front wheel, and the whole assembly connects to the bike and rotates about the steering axis via the headset bearings. Three styles of handlebar are common. Upright handlebars, the norm in Europe and elsewhere until the 1970s, curve gently back toward the rider, offering a natural grip and comfortable upright position. Drop handlebars "drop" as they curve forward and down, offering the cyclist best braking power from a more aerodynamic "crouched" position, as well as more upright positions in which the hands grip the brake lever mounts, the forward curves, or the upper flat sections for increasingly upright postures. Mountain bikes generally feature a 'straight handlebar' or 'riser bar' with varying degrees of sweep backwards and centimeters rise upwards, as well as wider widths which can provide better handling due to increased leverage against the wheel.
Hmm, I think it depends on the forest. My experience has been that if you have a Class 1 ebike and are riding respectfully, most places allow it. I have a sensitive knee and carry a doctor’s note citing disability laws in Colorado and have never been approached or asked by a ranger or fellow rider about the legality of my bike. That said, I have been using the really quiet and hidden Brose motor and I ride carefully and am friendly with everyone

While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers.  If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.  


The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.
As often preached, eBikes are arguably the most efficient, enjoyable and clean way to travel around the city. Here at Fully Charged, we have an eBike for all, from the eMTBs, to folding electric bikes. But certainly our most popular are urban commuter eBikes. For those bored of playing sardines on the tube, or taking … Continue reading Commuter eBike riding: The Fully Charged Picks

Many newer or smaller companies only design and market their products; the actual production is done by Asian companies. For example, some 60% of the world's bicycles are now being made in China. Despite this shift in production, as nations such as China and India become more wealthy, their own use of bicycles has declined due to the increasing affordability of cars and motorcycles.[102] One of the major reasons for the proliferation of Chinese-made bicycles in foreign markets is the lower cost of labor in China.[103]
Electric mountain bikes have garnered a lot of attention for their ability to help riders go higher, further, and faster on the trail. As a result, there have been some impressive new eMTB models to hit the market in recent years, making it easier than ever to head off-road. Our favorite is the Haibike SDURO HardNine, which comes equipped with a 350-watt Bosch Performance CX drive and a 500 watt-hour battery. This gives it a range of up to 70 miles, along with a top speed of 20 mph, which is plenty fast on singletrack.
State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[55] Subchapter J of Publication 45 spells out the vehicle requirements in full.
However, laws and terminology are diverse. Some countries have national regulations but leave the legality of road use for states and provinces to decide. Municipal laws and restrictions add further complications. Systems of classification and nomenclature also vary. Jurisdictions may address "power-assisted bicycle" (Canada) or "power-assisted cycle" (United Kingdom) or "electric pedal-assisted cycles" (European Union) or simply "electric bicycles". Some classify pedelecs as distinct from other bikes using electric power. Thus, the same hardware may be subject to many different classifications and regulations.
×