Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
It is important to note that if a vehicle has an electric motor greater than 500 watts and is capable of powering the vehicle when traveling at a speed greater than 32 km/h and it does not have a CMVSS compliance label it cannot be registered unless the owner can prove, by having the vehicle certified by an engineer, that it is safe for operation on NB highways. Also, not all vehicles are suitable for operation on NB highways and it could be that the vehicle in question may not be a motor driven cycle or a bicycle and cannot be operated on the highway at all.
Brock had been running his esoteric shop on Cambie St. for over 30 years, pioneering the sale and production of recumbent bikes, tricycles, velomobiles, unicycles, and of course electric bicycles well before any of these things were popular. He was dabbling with early ebike conversions in the 1990's when we were still in grade school and has been for many years one of the few shops always willing to say yes to electric retrofits. We hope to still see him riding around streets of Vancouver in a white velomobile.
Electric Bicycles are defined by the California Vehicle Code . In summary, electric bicycles are to be operated like conventional bicycles in California. There are several exceptions to this. A person must be at least 16 years old, and anyone riding an electric bicycle must wear a bicycle helmet. The e-bikes must have an electric motor that has a power output less than 1,000 watts, is incapable of propelling the device at a speed of more than 20 miles per hour on level ground, is incapable of further increasing the speed of the device when human power is used to propel the motorized bicycle faster than 20 miles per hour, operates in a manner so that the electric motor is disengaged or ceases to function when the brakes are applied, or operates in a manner such that the motor is engaged through a switch or mechanism that, when released, will cause the electric motor to disengage or cease to function.
"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Title 7, Chapter 551 entitled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D. Under Chapter 541.201 (24), "Electric bicycle" means a bicycle that is (A) designed to be propelled by an electric motor, exclusively or in combination with the application of human power, (B) cannot attain a speed of more than 20 miles per hour without the application of human power, and (C) does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle on a highway that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle on a highway used primarily by pedestrians.
Motor position – e-bike motors are positioned on either the front wheel hub, rear wheel hub, or in the middle of the bike between the pedals. There are pros and cons of each, but we think the mid-engine motor gives better weight distribution and the most natural bike riding feel. The pulling sensation you get from a front hub motor in particular can feel a bit unnatural
We are kicking off this series with a quick look at Keith Forbes. Keith showed up unannounced at our shop a year and a half ago, asking if there may be any work opportunities as he was considering a move to Vancouver from Trinidad and had something of a personal interest in transportation technology. We'll let the video show what he's been up to since then!