It is important to note that if a vehicle has an electric motor greater than 500 watts and is capable of powering the vehicle when traveling at a speed greater than 32 km/h and it does not have a CMVSS compliance label it cannot be registered unless the owner can prove, by having the vehicle certified by an engineer, that it is safe for operation on NB highways. Also, not all vehicles are suitable for operation on NB highways and it could be that the vehicle in question may not be a motor driven cycle or a bicycle and cannot be operated on the highway at all.
The battery is the pedelec’s power source. It supplies the motor with the electrical energy that is required to provide power assistance when cycling. So it is hardly surprising that there is frequent discussion and “talking shop” about the eBike’s battery in particular. What is the difference between batteries? How far can you go on a fully charged battery? What do you have to remember about storage? Thomas Raica, head of technical customer application, here provides information and advice.
China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008,[72] and reaching an estimated fleet of 120 million e-bikes in early 2010.[2][73] This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities.[72] Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car.[2] Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007.[73] By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.[72][73]
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]

Tires vary enormously depending on their intended purpose. Road bicycles use tires 18 to 25 millimeters wide, most often completely smooth, or slick, and inflated to high pressure in order to roll fast on smooth surfaces. Off-road tires are usually between 38 and 64 mm (1.5 and 2.5 in) wide, and have treads for gripping in muddy conditions or metal studs for ice.
Available products (motors, senors, batteries, control systems. etc.) change fast since the e-bike market shows a strong growth. In principle, get a rear motor if you want a lot of raw power and acceleration (e.g. for a 500W motor). Middle motors are more energy efficient and less subject to problems (e.g. overheating). Middle motors usually are combined with integrated rear hub gears, and rear motors with derailleurs. Both have advantages and disadvantages. E.g. the former require less maintenance, are easy to use in go-and-stop traffic, but require taking off weight on pedals when shifting. Therefore the latter (derailleurs) are better for speedy overland and hills cycling.
But unlike other battery mounted controllers, the Baserunner also stands on its own too. If you upgrade to a different battery model in the future that doesn't fit the cradle, simply remove the Baserunner from the base and use it as a miniature stand alone controller with your new battery pack. That's Grin thinking about your future options for you.
As electric bike options continue to expand, more brands are integrating the battery more seamlessly. That makes them look sleeker (and more like a real bike). Batteries are expensive, so make sure there’s a good way to lock the battery to your bike if you’ll be keeping it outside. Overall weight is important. Some battery and motors can add 15 pounds or more to the bike. With assist, you won’t feel that much when you’re riding, but you will if you have to carry your bike up stairs or lift it onto a bike rack.
Storage space: it’s one of the primary disadvantages to biking versus driving. A simple solution is attaching a basket or storage case to your bike’s frame or handlebars, giving you a convenient place to keep your essentials while you ride. A pannier rack is a useful option as well, which allows you to connect special pannier bags to your bike to create even more storage capacity.
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[65]

The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].


We'll start this off with the latest two Customer Profile videos. In the first one we follow up from the well received Leigh Cross video with a look at his son, Tig Cross. Tig's been refining an original bike concept combining the best parts of an ebike, scooter, and velomobile, and showcases the merits of an electric generator for the human drivertrain.
In my research about ebikes and the law, I cannot begin to justify how often articles about the laws evolved into the various ways and techniques to sneak around public notice and be stealth with the your ebike. The goal is to ride fast and fun, stay away from public awareness, and ‘Fly under the Radar’. I have been there and I get the drift. Sales and production are up. Electric bike kits, DIY enthusiast, long distance commuters, and a general drive for value is raising the desire for more options for consumers, wanting speed for fun and function, while developing amnesia for the law. People want to ride their new ebikes, and have the same access to safe pathways as they did the week before on their 100% human bike. Rather than deal with the inevitable conflicts over access, behavior and perception within the general public, the typical user will try to blend in with the normal cycling community.
Range is a key consideration with e-bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider.[36][37] Some manufacturers, such as the Canadian BionX or American Vintage Electric Bikes,[38] have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[39] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS. E-bikes developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains.[40] The bicycles were then charged from the mains, as is common today. While ebike batteries were produced mainly by bigger companies in past, many small to medium companies have started using innovative new methods for creating more durable batteries. State of the art, custom built automated precision CNC spot welding machines[41] created 18650 battery packs[42] are commonly used among Do-it-yourself ebike makers.
Photo: Could solar power be the future of electric bicycles? The large solar panel mounted over the back wheel of this experimental bike powers an electric motor connected by a chain drive to the back wheel, helping the rider when he doesn't feel like pedaling. Using clean, green solar power would remove the problem of having to charge electric bikes with electricity generated from fossil fuels—and help to extend their range significantly. Photo by Warren Gretz courtesy of US DOE/NREL.
This Class 3 (28 mph), utilitarian, road e-bike is smooth and torquey thanks to its Bosch Performance Speed motor. With a drop bar and traditional road-bike position and handling, the CrossRip+ is more suited to longer rides on mixed terrain than navigating congested city streets. It comes with a rear rack—for mounting bags, not for attaching cargo directly—full fenders, a kickstand, and integrated front and rear lights (which are powered by a Bosch 500Wh battery). It features a SRAM Force 1x11 drivetrain, hydraulic disc brakes, and wide 700x38mm tires.
Some electric bikes claim to use a neat trick called regenerative braking. If you start pedaling the bicycle or going downhill, the spinning wheels turn the electric motor in the hub in reverse and start charging up the batteries. In practice, regenerative braking is nowhere near as useful on an electric bicycle as it is on an electric train or car. An electric bike has much less mass and velocity than either a train or car, so it never gains (or loses) anything like as much kinetic energy when it starts and stops. You'd have to go down an awful lot of hills to charge up the batteries completely and that's usually not practical. And what's the point in pedaling the wheels simply to charge the battery? You might as well have bought an ordinary bicycle to start with!
The frame itself incorporates a series of mounts allowing you to easily trick-out the Road E+1 with a rack, fenders, or panniers to more aptly meet your touring requirements. Again, most touring purists will certainly scoff at the mere notion of pedal-assistance, however, individuals looking for more of a guided tour and less of a tour de force will swoon over the Road E+1.
The battery is the pedelec’s power source. It supplies the motor with the electrical energy that is required to provide power assistance when cycling. So it is hardly surprising that there is frequent discussion and “talking shop” about the eBike’s battery in particular. What is the difference between batteries? How far can you go on a fully charged battery? What do you have to remember about storage? Thomas Raica, head of technical customer application, here provides information and advice.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
On the other hand, the battery doesn’t lock into the bike, which means you can’t just leave it on your bike when you park at the bike rack. Anyone could walk by and simply remove your battery. That seems like an oversight to me, though perhaps the designers assumed that such a small battery would just be easy to take with you. And it is. My wife could probably lose this battery in her purse.
×