The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.
How do the State Laws relate to the 2001 Federal Law? This is a difficult question to answer and know how they apply to you individually. From the Federal Law, one would hope that your purchased ebike is simply classified as a bicycle, with all the rights and privileges allotted to a normal cyclist. However, State Laws are confusing because they may be more restrictive in parts and add other requirements. About 30 U.S. states still have confusing regulations around them. Either the bikes are technically classified as mopeds or motor vehicles, or they have equipment, licensing or registration requirements that cause problems for riders. Thanks to the People-For-Bikes/Bicycle Product Suppliers Association (BPSA) partnership with local advocacy groups, they have been able to make the case for streamlining state regulations so that e-bikes are essentially treated like regular bicycles.4
Parliament has decided to approve the speed pedelec – a type of super electric bike that can reach speeds of up to 45 km/hour – for riding on cycle paths. Danish Parliament has decided that as of July 1 2018 those operating the super bikes only need to have turned 15 and wear a helmet, while the licence and number-plate demands will no longer be in play. 
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.
Indian law requires that all electric vehicles have ARAI approval. Vehicles with below 250W and speed less than 30 km/h, do not require certification- hence not following full testing process, but needs to get exemption report from ARAI. Whereas more powerful vehicles need to go through a full testing process following CMVR rules. This can take time and cost money but assures safe and reliable design for Electric Vehicles. These regulations are not promulgated by the Regional Transport offices, and riders are not required to obtain a licence to drive, to carry insurance, or to wear a helmet.
It appears Tennessee has not passed any legislation that applies to electric bicycles. Some people think the laws pertaining to a Motorized Bicycle should be used for an electric bicycle. However, a Motorized bicycle would be a gasoline powered device per state law as it is defined as "means a vehicle with two (2) or three (3) wheels, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters (50cc) which produces no more than two (2) brake horsepower and is capable of propelling the vehicle at a maximum design speed of no more than thirty miles per hour (30 mph) on level ground." 
If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
Electric bicycles use batteries as a source of power and a quiet DC motor as a driving mechanism. On most e-bikes the motor is built directly into the wheel (known as a hub motor) and the batteries are discreetly hidden in the rear rack or frame. Electric bikes can be operated just like normal bicycles, but they can also be power-driven by a throttle or pedaled with the help of pedal-assist (PAS or pedelec).
There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.
Perhaps the cleverest thing of all about the Electric Brompton is that despite all the extra stuff, it folds up exactly the same as the non-powered variety. It's so simple, and unlike certain folding bikes we could mention, what you're left with is a genuinely small thing, rather than something that's about the size of a bike with the front wheel taken off.