"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
The battery is the pedelec’s power source. It supplies the motor with the electrical energy that is required to provide power assistance when cycling. So it is hardly surprising that there is frequent discussion and “talking shop” about the eBike’s battery in particular. What is the difference between batteries? How far can you go on a fully charged battery? What do you have to remember about storage? Thomas Raica, head of technical customer application, here provides information and advice.
Electric bikes aren’t just a practical and environmentally conscious solution to gridlock, they also are really fun to ride. On top of all of the persuasive arguments to get an electric bike, I think the Rad Wagon’s best-selling point comes down to enjoyment. Zooming down the street each morning I wasn’t angrily yelling at fellow drivers or rushing not to be late. The bike commute was part of the journey each day, and not just the means I used to get around. There’s a reason so many people loved biking as a kid, and it can be just as fun as an adult.
By 2001 the terms, E-Bikes, power bike, pedelec, assisted bicycle and power-assisted bicycle where commonly used to describe electric bicycles. E-bike, according to Google, is a term that has increased in trend. This term generally referred to an electric bicycle which used a throttle. The terms Electric Motorbike or E-Motorbike have been used to describe more powerful models which attain up to 80 km/h.
The Footloose has no chain, however -- it's entirely electrically driven. It takes very little effort to get to your destination, meaning you arrive at work without having broken a sweat. The downside is that when you run out of power, you're not going anywhere. And pedalling from a standstill, waiting for the motor to kick in, is an odd sensation that takes some getting used to.
Unrelated to the show but also of local interest. The BC government is soliciting input on what is meant by "active transportation" which could hopefully help to direct policy and regulation governing not just ebikes but all kinds of human scaled transport. If you think electric skateboards should be on their radar or faster S-Pedalec class ebikes then this is a chance to have your voice heard. Electric bicycles have been an entirely grass roots phenomenon for most of their trajectory and it's encouraging to see the entire scope of personal mobility finally being acknowledged and discussed at this level.
The Dew-E packs functionality and fun into a rather traditional and conservative package. Front and rear fenders, integrated Busch & Müller front and rear lights, and a built-in Abus wheel lock make this a very practical commuter bike. An 11-34, 9-speed cassette and 1.75-inch tires provide versatility: You’ll ride smooth over rough city streets and zip down gravel bike paths with confidence. Front and rear rack mounts also give you the chance to outfit this bike for carrying more cargo or supplies for a longer day on the bike.
The first mechanically-propelled, two-wheeled vehicle may have been built by Kirkpatrick MacMillan, a Scottish blacksmith, in 1839, although the claim is often disputed. He is also associated with the first recorded instance of a cycling traffic offense, when a Glasgow newspaper in 1842 reported an accident in which an anonymous "gentleman from Dumfries-shire... bestride a velocipede... of ingenious design" knocked over a little girl in Glasgow and was fined five shillings.
Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.
It appears Tennessee has not passed any legislation that applies to electric bicycles. Some people think the laws pertaining to a Motorized Bicycle should be used for an electric bicycle. However, a Motorized bicycle would be a gasoline powered device per state law as it is defined as "means a vehicle with two (2) or three (3) wheels, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters (50cc) which produces no more than two (2) brake horsepower and is capable of propelling the vehicle at a maximum design speed of no more than thirty miles per hour (30 mph) on level ground." 
It arrived safely, well packaged. It also shipped really quickly too. If you want to have an ebike for rides, this bike will work. it really helps to get over a couple steep hills. With pedal assist or the throttle it is like riding on a flat surface when it comes to inclines. The bike seems well constructed. The disc brakes work great, and the wheels and tires are very sturdy. For the price I think it was a very good deal.
At the top end, the 20mph speed limit isn't an absolute, like the speed of light. It's just the most you'll get from the motor. I was able to get it up to 28mph on a flat road (there are no other roads where I live) in Turbo mode and 8th gear, but it took hard work to get there and maintain the speed. The easiest comparison is my mountain bike, where I've hit 23mph on that same stretch of road—and that took a heck of a lot of effort. Exactly how much effort does it take to ride? I have a 15-mile route that I ride on both my mountain bike and cyclecross bike. According to my Apple Watch, I generally burn around 1,400 or so calories on a brisk ride. I'll probably average around 13mph or so on my Marlin and between 16 and 17.5mph on my XO2. I averaged 14.9mph and burned a hair over 1,000 calories with the Bulls Cross E8.
Übrige "Motorfahrräder": “E-Bikes mit einer Leistung zwischen 500 und 1000 Watt oder einer bauartbedingten Höchstgeschwindigkeit von 20 bis 30 km/h oder einer Tretunterstützung, die auch bei einem Tempo von 25 – 45 km/h wirkt, gelten als Motorfahrräder und benötigen ein entsprechendes Kontrollschild.”. You can use any bicyle path and also hiking roads forbidden to motorbikes if you drive slowly.
Geared Hub Motors – Most pre-built e-bikes use brushless geared hub motors. These motors have internal planetary gears that help transfer power from the motor to the wheel. Because of the internal gearing, these motors provide excellent torque but are limited in top speed. On the plus side, the improved torque means better take-off power and hill climbing ability. Plus, less wattage is required to get the motor turning and they’re typically small and lightweight. On pre-built e-bikes, these motors range from 200w-500w and go up to 20mph. But some aftermarket kits can be as powerful as 1000w, with increased top speeds and huge amounts of torque (ideal for extremely hilly terrain). Besides lower top speeds, these motors tend to be expensive and it’s possible the gears will eventually wear out and need to be replaced (this is highly unlikely, they las quite a long time). Good examples are Ancheer bikes.
Besides voltage, batteries are rated by amp hours (AH). Although voltage seems to get the most attention, the amp hour rating of the battery is just as important. It is the measure of a battery’s capacity and provides a good indication of the range you can expect from an electric bike. Although lots of factors come into play in determining range (ie: rider weight, terrain, input, efficiency, etc.), a good rule of thumb is range is equal to AH. So under normal conditions, an average rider can expect 10 miles out of a 10AH battery (with no pedaling). With rider input, this number can be dramatically increased, so most 10AH batteries are rated “up to 20 miles” by the manufacturer which assumes pedaling. On pedal-assist bikes (which require pedaling), the range ratings are much higher because the rider is constantly assisting the motor and reducing the current draw.
As of 2005, where Federal funds have been used in the construction of bicycle or pedestrian paths motor vehicles including electric bicycles (here defined as having a motor weighing less than Template:Convert) are not permitted unless State or Local regulations permit . This was known as the Transportation Equity Act for the 21st Century (TEA-21), or Public Law 105-178, or by its 2003 re-authorization which expired in 2005 the Safe, Accountable, Flexible, Efficient Transportation Equity Act (SAFETEA-LU).
While I would have loved to see some higher end components such as disc brakes or built-in lights, the bike still works well for what you get and is a pretty good value for the price. One missing component that I feel would make a big difference is a kickstand. I’ve never seen an e-bike that didn’t come with one, outside of ultra premium multi-thousand dollar road and downhill e-bikes that try to save every gram of weight. But for a commuter, a kickstand is pretty important. You can always add a cheap $7 kickstand from Amazon, but I would have preferred they save us the step and include their own cheap kickstand.
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle(they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.
Front-Mounted Hub Motor can be found on pre-built bikes or on custom conversions. Mounted to the front wheel, this is the easiest configuration to setup if you’re converting a standard bicycle since there’s no derailleur or chain to worry about. And since most e-bike conversions include batteries mounted to the rear rack, using a front hub motor helps equalize the weight of the bike and makes it easier to handle. But there’s a small risk the motor could cause the front forks to brake. That’s why it’s vital you only use a front hub motor on a steel fork. For pre-built bikes, this shouldn’t be an issue since the motors are usually lower-powered on steel forks.
An e-bike is identified as a "motor assisted cycle" (MAC) in British Columbia, which differs from electric mopeds and scooters, which are "limited-speed motorcycles." Motor assisted cycles must: have an electric motor of no more than 500 W; have fully operable pedals; not be capable of propelling the device at a speed greater than 32 km/hr [19.9 mph]. The engine must disengage when (a) the operator stops pedaling, (b) an accelerator controller is released, OR (c) a brake is applied. A driver's license, vehicle registration, and insurance are all not required. A bike helmet must be worn.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
This dexterous electric dirt bike is recommended for anyone over the age of 14. It’s fitted with double suspension and big tyres to help you tackle tough terrain. You also get a good selection of gears, that gives you optimal control. The Razor can go as fast as 15 mph on average, and comes with an excellent braking system. The aesthetics are on point, and the racer look is sure to impress. Don’t forget your helmet!
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
And let’s not forget the economic advantages of owning an e-bike. The annual cost of running a new family car is, on average, about $9,000 per year. Running an electric bike costs around $400 per year. And while filling a gas tank costs around $30, recharging an electric bike battery costs only about 50 cents. A tank of gas may get you further, but not 60 times further!
Can I legally buy/build and ride an ebike that’s faster than 20 mph? Yes you can, but you need to know that the ebike is no longer considered equivalent to a bicycle and is subject to other state vehicular classifications. The definitions for electric bikes spanning 20-30mph, and 1-2 horsepower ranges, will vary from state to state, resulting in a no-man’s-land consensus about limits for motor vehicle definition. The common label for a 20-30mph, 2-wheeled vehicle with active pedals is a Moped. Other MVA labels include motor scooter, motorbike and dirt bike which may have equivalent power and speed performance, but do not have pedals to assist and move the vehicle.
Most European bike rules are tight and restrictive. Right now the California state ebike rules in AB 1096 provide the clearest and cleanest format, and they support ebike riding. No other U.S. regulations come close. The big brand ebikes (Giant, Specialized, Trek) are selling bikes that fit within European rules (250w-300w motors). This gives them economies of scale.
Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.
This was the first ebike I ever bought. I've since become a builder and make my own. But this was a really reliable vehicle. I used it everyday for transportation. The company sent me any part I needed. It's got a power motor on it so it's super reliable. I wouldn't hesitate to buy this bike especially if you're new into the ebike world. If your looking to have some real fun buy this bike.. If your looking to meet new people buy this bike. If looking to go more green buy this bike. This bike is so much fun you well want to ride all day. This bike should be twice the price . I love love love it .
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.
The Ohio Revised Code 4511.01  distinguishes motorized bicycles and mopeds from motorcycles or scooters by describing them as "...any vehicle having either two tandem wheels or one wheel in the front and two wheels in the rear, that is capable of being pedaled and is equipped with a helper motor of not more than fifty cubic centimeters piston displacement that produces no more than one brake horsepower and is capable of propelling the vehicle at a speed of no greater than twenty miles per hour on a level surface." One brake horsepower converts to 0.75 kW, or (rounded) 750W. Thus, a bicycle with an electric helper motor operating under 750W, and not propelling the bicycle over 20 mph, does not qualify to be registered under Ohio state law. Local jurisdictions may have other regulations.
Some components, which are often optional accessories on sports bicycles, are standard features on utility bicycles to enhance their usefulness, comfort, safety and visibility. Mudguards, or fenders, protect the cyclist and moving parts from spray when riding through wet areas and chainguards protect clothes from oil on the chain while preventing clothing from being caught between the chain and crankset teeth. Kick stands keep bicycles upright when parked, and bike locks deter theft. Front-mounted baskets, front or rear luggage carriers or racks, and panniers mounted above either or both wheels can be used to carry equipment or cargo. Pegs can be fastened to one, or both of the wheel hubs to either help the rider perform certain tricks, or allow a place for extra riders to stand, or rest. Parents sometimes add rear-mounted child seats, an auxiliary saddle fitted to the crossbar, or both to transport children. Training wheels are sometimes used when learning to ride.
Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3-wheeled bicycle that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Canadian Motor Vehicle Safety Standards (CMVSS) for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1–5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for each. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities.
Electric bikes (also known as e bikes) are perfect for long-distance riding, or when you just don’t feel like giving your full effort. What differentiates them from electric motorcycles is the ability for the rider to pedal the bike at any time, so if you’re riding along and your battery dies, you’re not going to stranded. These are often very valuable bikes, but some models can be more affordable than you might expect, especially when you treat them as a form of transportation as opposed to thinking of the price in terms of regular bicycles.
Are there any guidelines you could give on what is legal in Federal Parks that have duel use pedestrian and bike paths. I was recently told that E bikes are not allowed on a Federal trail even though much faster 10 and 20 speed bicycles are common. I also stated that I have a disability which prevents me from walking or biking very far but was still told my bike was not allowed. I should also add that my bike has a top speed of about 15 and is 250 watts.
In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear wheel, or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.
Built by a company that’s made cycling equipment for more than four decades, the Vado feels more like a traditional bicycle than almost any other ebike. Its frame and components have been tuned to provide a familiar experience, making it easy for new and long-time cyclists to jump on and start pedaling. Specialized’s heritage shines through nicely, helping separate itself from the competition in an increasingly crowded ebike market.
As electric bike options continue to expand, more brands are integrating the battery more seamlessly. That makes them look sleeker (and more like a real bike). Batteries are expensive, so make sure there’s a good way to lock the battery to your bike if you’ll be keeping it outside. Overall weight is important. Some battery and motors can add 15 pounds or more to the bike. With assist, you won’t feel that much when you’re riding, but you will if you have to carry your bike up stairs or lift it onto a bike rack.