If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
The motor isn’t insanely powerful, but it gets you up to full speed quickly enough. I never felt like the bike was underpowered. The motor does make more noise than a lot of other hub motor bikes I’ve ridden though. There’s a definite whirrr to the motor caused by the internal plastic gears. While all geared motors will have some level of gear noise, this one stuck out more to me than others.
Louisiana Revised Statute R.S. 32:1(41) defines a motorized bicycle as a pedal bicycle which may be propelled by human power or helper motor, or by both, with a motor rated no more than one and one-half brake horsepower, a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which produces a maximum design speed of no more than twenty-five miles per hour on a flat surface. Motorized bicycles falling within this definition must be registered and titled under Louisiana law. Additionally, a motorized bicycle operated upon Louisiana roadways or highways by a person fifteen years of age or older and producing more than five horsepower must possess a valid driver's license with a motorcycle endorsement and adhere to laws governing the operation of a motorcycle, including the wearing of approved eye protectors or a windshield and the wearing of a helmet. The statute also states that "Motorized bicycles such as pocket bikes and scooters that do not meet the requirements of this policy shall not be registered."
Range is a key consideration with e-bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. Some manufacturers, such as the Canadian BionX or American Vintage Electric Bikes, have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging. This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS. E-bikes developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains. The bicycles were then charged from the mains, as is common today. While ebike batteries were produced mainly by bigger companies in past, many small to medium companies have started using innovative new methods for creating more durable batteries. State of the art, custom built automated precision CNC spot welding machines created 18650 battery packs are commonly used among Do-it-yourself ebike makers.
In summary, federal law trumps all States’ laws. That is true with bicycle law, too. States cannot constitutionally pass legislation that reduces or eliminates Federal laws, they can only pass legislation that enacts additional (tighter) restrictions on its people. States can’t define an ebike a bicycle if greater than 750W/20mph, nor can they define an ebike a motor vehicle if less than the Federal Government’s limit of 750 Watts and a top electric-powered speed of 20 MPH.3This is the Federal definition of a low speed electric bike, which equates it to a bicycle.
Before you start shopping around for a new e-bike, the first thing you should ask yourself is, “how do I plan on using an electric bicycle?” How far do you plan on traveling? What type of terrain will you be traveling on? How much assistance do you need? Do you plan on pedaling – or do you want the bike to do all the work? Is this bike for daily commuting or casual riding? How fast do you need to go?
Yes, there are less expensive ebikes on the market but most come with a few serious caveats. The Espin Sport delivers on the full promise of an electric bike, but in a more affordable fashion. This bike isn’t going to tow you around for a 60-mile round-trip endeavor but those seeking their first ebike will get plenty of return on their investment with this model.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
Did you know that electric bikes can be used for fitness training? Or that they have been scientifically proven to increase the amount of cycling people do? Or that they have proven health and fitness benefits? Well, it’s all true! Apart from being tons of fun, ebikes can be used to improve health and fitness in many ways. Here are our top posts about how ebikes can improve your health and fitness.
Oregon Law (ORS 801.258) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed no greater than 20 miles per hour on level ground.
There are specialized bicycle tools for use both in the shop and on the road. Many cyclists carry tool kits. These may include a tire patch kit (which, in turn, may contain any combination of a hand pump or CO2 Pump, tire levers, spare tubes, self-adhesive patches, or tube-patching material, an adhesive, a piece of sandpaper or a metal grater (for roughing the tube surface to be patched), Special, thin wrenches are often required for maintaining various screw fastened parts, specifically, the frequently lubricated ball-bearing "cones". and sometimes even a block of French chalk.), wrenches, hex keys, screwdrivers, and a chain tool. There are also cycling specific multi-tools that combine many of these implements into a single compact device. More specialized bicycle components may require more complex tools, including proprietary tools specific for a given manufacturer.
this bike came really fast. Very surprised at the quality considering the price. It was packaged very well however my fenders had a little kink in it during shipping. I don’t care about that. It is very fast and a solid bike. I own two other Nami electric folding bikes and this is on par with their quality. The only concerns I have is whether or not I’m able to purchase a second battery when this one needs replacement. This is my first electric bike and I’m very impressed with the fun factor.
There are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia.
And let’s not forget the economic advantages of owning an e-bike. The annual cost of running a new family car is, on average, about $9,000 per year. Running an electric bike costs around $400 per year. And while filling a gas tank costs around $30, recharging an electric bike battery costs only about 50 cents. A tank of gas may get you further, but not 60 times further!
Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.
In Opinion No. 2007-00602 of the Attorney General, Jim Hood clarified that a "bicycle with a motor attached" does not satisfy the definition of "motor vehicle" under Section 63-3-103. He stated that it is up to the authority creating the bike lane to determine if a bicycle with a motor attached can be ridden in bike lanes. No specifications about the motor were made.
Mid-mounted system means that the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. Mid-drive systems tend to feel more like a normal bike, since they drive the pedals, just like your legs, and those who frequently climb long, steep hills tend to prefer mid-drive systems for their ability to handle long climbs. As they can leverage the bicycles lowest gears for climbs, mid drive systems can also leverage the high gears to reach higher speeds on flat areas than a hub system. The mid-drive motor drives the crank, instead of the wheel itself, which multiplies its power and allows it to better take advantage of the bike’s existing gears. If the rider changes the gears appropriately, the motor can turn closer to its ideal rotations per minute which makes a huge difference while climbing hills, so this is a perfect option for those who love mountain biking.
Not all electric bicycles take the form of conventional push-bikes with an incorporated motor. Some are designed to take the appearance of low capacity motorcycles, but smaller in size and comprising of an electric motor rather than a petrol engine. Bicycles of note include the Sakura electric bicycle, which incorporates a 200W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one based on its similarity in appearance.
In cities where bicycles are not integrated into the public transportation system, commuters often use bicycles as elements of a mixed-mode commute, where the bike is used to travel to and from train stations or other forms of rapid transit. Some students who commute several miles drive a car from home to a campus parking lot, then ride a bicycle to class. Folding bicycles are useful in these scenarios, as they are less cumbersome when carried aboard. Los Angeles removed a small amount of seating on some trains to make more room for bicycles and wheel chairs.
When you have the electric motor turned on, it engages with your first push of the pedals. The difference in acceleration is startling compared to any other bike I've ridden. In Eco mode, I could sprint from 0 to 20mph in about 200 feet/65m. Switch to Turbo, and it's about 150/30m feet. As I mentioned above, you still have to pedal. The difference with an electric bike is the feeling of getting more bang for the buck. And if you want to be lazy, you can. Stay in third or fourth gear and you'll be able to stay around 18-19mph with minimal effort. But if you want to go much faster than 20mph, you'll need to work.
E-bikes can boost bike usage, offer health benefits and use “an order of magnitude less carbon dioxide than a car traveling the same distance,” according to a 2016 research review published in the journal Transport Reviews. In fact, access to an e-bike increased cycling trips and distances traveled – and nearly doubled the bike as a mode of transportation, observed one Norwegian study.
We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.
As long as you can do without some of the perks that pricier models offer—like a detailed display unit, integrated lights, and a torque-sensor motor—the August Live! LS is a solid, stable, comfortable, and really freakin’ cute (have you see those polka-dot fenders?) e-bike. Its 8-speed twist shifter, chopper-style handlebar, Touch Down Geometry (for a more laid-back ride), and three levels of assist keep this bike within the realm of “cruiser.” But with a 250-watt Bafang rear-hub motor, a top pedal-assisted speed of 20 mph, and reliable disc brakes, the August is no joke. It’ll get you to the top of relatively steep climbs without forcing you out of the saddle, and it feels super stable on the way back down. It has a battery range of 20 miles, but that’s enough to take it where it’s happiest: tootling along at the beach, around town, and through the park.
The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations. The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.
However, Emu sells a little foldable number if that's your bag. The Emu Crossbar is for town commuters that require a sweet ride that's backed up by solid Shimano Nexus hub gears and Tektro brakes, which are adequate if not the best on the market. Riding is smooth and easy, with the crank moving sensor doing its best to iron out any gaps in power delivery.
Again, these are base level components here. The Shimano/TX55 gearing is fine for this application level but I have lost my chain a few times in a few weeks. The frame is surprisingly solid aluminum alloy which feels stiffer and lighter than last year’s Ancheer. The supplied front 10W light is very bright, however the back light is charged via USB and has a push button rather than being wired into the controller. The disc brakes are the same no-name brand as the Ancheer but appear to be a size bigger. The fork, while not amazing, is a big improvement in stiffness and give over the Ancheer’s, which scared me a bit.
In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.
What I found most interesting is how my cycling habits changed over my two weeks with the eBike, mostly for the better. In most states, cyclists need to come to a complete stop at stop signs... and as anyone who has ever ridden a bike or shared a road with a cyclist knows, most cyclists generally do an Idaho Stop if they believe it's safe. I do it, too. Knowing that I could quickly get back up to speed with the aid of the electric motor, I found myself more willing to sacrifice my forward momentum and come to a complete stop when there was a car approaching an intersection.
And the last product update to kick off the year is the pilot release of our new Baserunner motor controller. We spent much of last summer and fall trying to cram an even more miniature version of the Phaserunner into compact profile that could fit inside the controller cavity of the popular Hailong downtube battery cradles, and by golly we did it. While not as powerful as the Phaserunner (just 55A max phase current, and 60V max battery voltage), the Baserunner is perfectly suited to the smaller geared and direct drive hub motors using the Higo Z910 plug. This allows for a very tidy installation with no separate controller to mount.
China's experience, as the leading e-bike world market, has raised concerns about road traffic safety and several cities have considered banning them from bicycle lanes. As the number of e-bikes increased and more powerful motors are used, capable of reaching up to 30 miles per hour (48 km/h), the number of traffic accidents have risen significantly in China. E-bike riders are more likely than a car driver to be killed or injured in a collision, and because e-bikers use conventional bicycle lanes they mix with slower-moving bicycles and pedestrians, increasing the risk of traffic collisions.
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
Brock had been running his esoteric shop on Cambie St. for over 30 years, pioneering the sale and production of recumbent bikes, tricycles, velomobiles, unicycles, and of course electric bicycles well before any of these things were popular. He was dabbling with early ebike conversions in the 1990's when we were still in grade school and has been for many years one of the few shops always willing to say yes to electric retrofits. We hope to still see him riding around streets of Vancouver in a white velomobile.
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead.
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.