Generally they are considered vehicles (like motorcycles and pedal cycles), so are subject to the same rules of the road. Regulations may define maximum power output and for electric bikes may or may not require an interlock to prevent use of power when the rider is not pedaling. In some cases regulatory requirements have been complicated by lobbying in respect of the Segway HT.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]

European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[142]
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.
Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.

When I finally had the ability drive this thing in my city, it feels fantastic, you're cruising easily. But the minute it starts going up a hill, you also gotta peddle to help it go up. Which is okay because the little engine helps a lot so you're not straining yourself. But, being that the wheels are so small, after a while, you feel your legs get swore. I guess the size of the wheel

Urban riding will never be the same, and cars will be in your way when you climb aboard the Specialized Turbo Vado 3.0. The zippy 28mph pedal-assist motor will leave you feeling invincible as you’re ripping along in turbo mode (which adds up to 320 percent of your power output). Although designed with female riders in mind—it comes with a women-specific saddle and grips, and a lower standover—the step-through frame is extremely convenient for anyone who doesn’t want to swing their leg over the back of a saddle while wearing street clothes. Slick, integrated lights, as well as fenders and a rear rack, add to the already-awesome features of this bike to make it the ideal combination of value, performance, and pep.


The frame of a fat e-bike resembles that of a traditional bike, with front and rear portions that are a bit wider to accommodate the large tires. Your height and weight will dictate which frame size suits you best. You’ll want to go through the process of mounting and dismounting the bike to make sure you’re comfortable climbing on and off before you commit to it.
Before you start shopping around for a new e-bike, the first thing you should ask yourself is, “how do I plan on using an electric bicycle?” How far do you plan on traveling? What type of terrain will you be traveling on? How much assistance do you need? Do you plan on pedaling – or do you want the bike to do all the work? Is this bike for daily commuting or casual riding? How fast do you need to go?
The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations.[63] The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.
Toe-clips and toestraps and clipless pedals help keep the foot locked in the proper pedal position and enable cyclists to pull and push the pedals. Technical accessories include cyclocomputers for measuring speed, distance, heart rate, GPS data etc. Other accessories include lights, reflectors, mirrors, racks, trailers, bags, water bottles and cages, and bell.[52] Bicycle lights, reflectors, and helmets are required by law in some geographic regions depending on the legal code. It is more common to see bicycles with bottle generators, dynamos, lights, fenders, racks and bells in Europe. Bicyclists also have specialized form fitting and high visibility clothing.
There are two basic categories of electric bike, and their uses don't offer equal crossover value. The first category is essentially a normal bicycle that has been outfitted with an electric motor. These bikes are the same size as a standard bicycle, and handle almost identically, save for the obvious benefit of added motive power thanks to a motor and battery.
In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.
Bicycle manufacturing proved to be a training ground for other industries and led to the development of advanced metalworking techniques, both for the frames themselves and for special components such as ball bearings, washers, and sprockets. These techniques later enabled skilled metalworkers and mechanics to develop the components used in early automobiles and aircraft.
Some prohibitions also apply, such as on: carrying cargo that prevents keeping at least one hand on the handlebars or prevents proper use of brakes, riding no more than two abreast on a roadway or shoulder, and attaching the bicycle to another vehicle. Minn. Stat. § 169.222, subds. 3-5. The vehicles may be operated on a sidewalk except in a business district or when prohibited by a local unit of government, and must yield to pedestrians on the sidewalk. Minn. Stat. § 169.223, subd. 3. By default, electric-assisted bicycles are allowed on road shoulders as well as on bicycle trails, bicycle paths, and bicycle lanes.
At the top end, the 20mph speed limit isn't an absolute, like the speed of light. It's just the most you'll get from the motor. I was able to get it up to 28mph on a flat road (there are no other roads where I live) in Turbo mode and 8th gear, but it took hard work to get there and maintain the speed. The easiest comparison is my mountain bike, where I've hit 23mph on that same stretch of road—and that took a heck of a lot of effort. Exactly how much effort does it take to ride? I have a 15-mile route that I ride on both my mountain bike and cyclecross bike. According to my Apple Watch, I generally burn around 1,400 or so calories on a brisk ride. I'll probably average around 13mph or so on my Marlin and between 16 and 17.5mph on my XO2. I averaged 14.9mph and burned a hair over 1,000 calories with the Bulls Cross E8.
Bike is awesome, warranty support has so far delivered, but is a hassle to deal with (and hassle is acceptable and better than nightmare, or unresponsive/clueless/unhelpful/not-english-speaking). To be fair, this is the middle of Swag's busy season. Check tire inflation, check and tighten fasteners, seatpost and handlebars and stem out of the box, RTFM, charge the battery and you're out the door riding quickly.
Maintenance of adequate tire inflation is the most frequent and troublesome concern for cyclists and many means and methods are employed to preserve pneumatic integrity. Thicker tires, thicker tubes, tire liners (of a number of rather impenetrable devices installed between the tire and tube), liquid sealing compounds squeezed into the tube, and automotive-style patch kits are all used to reliably contain the typical tire pressures of 40 to 60 pounds per square inch that are required for bicycle operation. Thin, light bicycle tires are particularly vulnerable to penetration and subsequent deflation caused by goat's heads and other burs, colloquially known as stickers. Inflation of bicycle tires to pressures higher than typical for automotive use requires special pumps. The complexity of bicycle tire maintenance and repair may cause many to not consider the bicycle for transport or leisure.
Across Europe, where e-bikes were embraced by the public long before the rest of the world, e-bike growth has averaged in excess of 20 percent each year between 2014 and 2017, with a whopping 25.3 percent growth to a total of two million e-bike sales in 2017. Analysts predict that strong growth will continue, with worldwide e-bike sales expected to hit $23.83 billion by 2025. A lot of that growth will be right here in the US.
Electrically-assisted cycles are usually classified as either pedelecs or e-bikes. Under European Union regulations adopted in the UK in June 2003, only power-assisted cycles meeting the pedelec classification are considered to be pedal cycles. The maximum power allowed in the European Union for (pedelec) electric bicycles is 250 W, with a maximum assisted speed of 25 km/h.[15]. To meet the pedelec specification the electric motor must be activated by the rider's pedalling effort and the power must cut out completely whenever the rider stops pedalling. Control of the motor by pedalling is often the key difference between a pedelec and e-bike.
Range is a key consideration with e-bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider.[36][37] Some manufacturers, such as the Canadian BionX or American Vintage Electric Bikes,[38] have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[39] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS. E-bikes developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains.[40] The bicycles were then charged from the mains, as is common today. While ebike batteries were produced mainly by bigger companies in past, many small to medium companies have started using innovative new methods for creating more durable batteries. State of the art, custom built automated precision CNC spot welding machines[41] created 18650 battery packs[42] are commonly used among Do-it-yourself ebike makers.
Great bike. Easy to assemble by yourself but if you have a rack let pros do it. No charge for that. Contacted the Addmotor people a few times and they got back quickly even on weekends. Great service. Bike is solid as a rock and excellent components. Only drawback is lack of fenders which I hope someone can manufacture. I would buy again in a nano second!
"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Title 7, Chapter 551 entitled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D.[131] Under Chapter 541.201 (24), "Electric bicycle" means a bicycle that is (A) designed to be propelled by an electric motor, exclusively or in combination with the application of human power, (B) cannot attain a speed of more than 20 miles per hour without the application of human power, and (C) does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle on a highway[132] that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle on a highway used primarily by pedestrians.
Motor position – e-bike motors are positioned on either the front wheel hub, rear wheel hub, or in the middle of the bike between the pedals. There are pros and cons of each, but we think the mid-engine motor gives better weight distribution and the most natural bike riding feel. The pulling sensation you get from a front hub motor in particular can feel a bit unnatural
DON'T BUY THIS BIKE!!!!! Worst customer service ever!!! I bought this bike for my 18 year old son to commute to school. It worked well for the first 2 months but the battery is cheap and stated to wear out. I tried going on the website, but they battery shows as out of stock, and has been for 3 months now. I left 5 emails with customer service, never got a reply. Also there is no number listed on their website to even speak to a real person. Now I have a worthless 5 month old bike..... horrible this company should be ashamed.
To legally operate a motorized bicycle or electric-assisted bicycle the operator must be licensed, the motorized bicycle/electric-assisted bicycle must be registered in one of the following definitions and meet the required safety equipment. If the operator or the motorized bicycle/electric- assisted bicycle does not meet all requirements, they will not be legal for street/highway use (including the sidewalk).To qualify as a motorized bicycle under state law they need to have motor of a piston displacement capacity of 50 cubic centimeters or less, maximum of two brake horsepower, maximum speed of not more than Template:Convert on a flat surface, fully operable pedals for human propulsion are not required, but may be a part of the machine.
"Bicycle" means either of the following: (1) A device having two wheels and having at least one saddle or seat for the use of a rider which is propelled by human power. (2) A device having two or three wheels with fully operable pedals and an electric motor of less than 750 watts (one horsepower), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden, is less than 20 miles per hour.[citation needed],

The BC Bike Show is the premier cycling and outdoors event in Western Canada and is happening in just 2 weeks on March 2nd and 3rd. We'll be there of course, and in addition to our exhibitor booth we'll also be hosting Cycle Stage to give more public presentations. On Saturday at 11:45 am we'll talk on how to navigate the various motor and battery options available for ebike retrofits, and on Sunday at 2pm we'll be doing a live demonstration of a regular bicycle being converted over to electric assist.
Mid-mounted system means that the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. Mid-drive systems tend to feel more like a normal bike, since they drive the pedals, just like your legs, and those who frequently climb long, steep hills tend to prefer mid-drive systems for their ability to handle long climbs. As they can leverage the bicycles lowest gears for climbs, mid drive systems can also leverage the high gears to reach higher speeds on flat areas than a hub system. The mid-drive motor drives the crank, instead of the wheel itself, which multiplies its power and allows it to better take advantage of the bike’s existing gears. If the rider changes the gears appropriately, the motor can turn closer to its ideal rotations per minute which makes a huge difference while climbing hills, so this is a perfect option for those who love mountain biking.
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:
×