Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2 [123] as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
Speed Pedelec ebikes – A new classification of bikes called ‘Speed Pedelecs’ have emerged which technically meet the bicycle definition for a 20 mph ebike. These ebikes are designed to max out at 28 mph. Pedelecs are pedal activated vs throttle activated. The weasel words within the definition says, “20mph on motor alone”. Thus, a person who adds their leg power to the motor assist and happens to cruise at 28mph is NOT doing it by motor alone, and therefore the bike is considered to be compliant with the Federal Law. If the rider stops pedaling, the speed pedelec cannot maintain speed. Speed Pedelecs are becoming more popular in Europe and America, which means more models are being offered.
Included in this shipment are the much awaited 3540 motors with their slick "UFO" design. These are the replacements for the older square style "H" motors, you may have noticed that this change was implemented last year with the 3525 front and rear motors. As always, we have the motors customized with a 10K NTC thermistor for thermal rollback using the CA3.
I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
(2) BICYCLE.--Every vehicle propelled solely by human power, and every motorized bicycle propelled by a combination of human power and an electric helper motor capable of propelling the vehicle at a speed of not more than 20 miles per hour on level ground upon which any person may ride, having two tandem wheels, and including any device generally recognized as a bicycle though equipped with two front or two rear wheels. The term does not include such a vehicle with a seat height of no more than 25 inches from the ground when the seat is adjusted to its highest position or a scooter or similar device. No person under the age of 16 may operate or ride upon a motorized bicycle.
We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
This thing is also kitted out with a full SRAM groupset, RockShox Yari RC front shocks, Custom Fox Float suspension at the rear and enormously punchy SRAM disc brakes at the front and rear. Fundamentally, it's a mighty off-road machine with pro-spec kit that introduces a new style of trail riding, allowing adrenaline junkies to ride further, climb harder and descend faster than ever before.
In Quebec power-assisted bicycles are often classified similarly to standard pedal bicycles. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles. The Quebec Highway Safety Code defines a power-assisted bicycle as a bicycle with an electric motor. PABs are permitted on the road in the province of Quebec.
In my research about ebikes and the law, I cannot begin to justify how often articles about the laws evolved into the various ways and techniques to sneak around public notice and be stealth with the your ebike. The goal is to ride fast and fun, stay away from public awareness, and ‘Fly under the Radar’. I have been there and I get the drift. Sales and production are up. Electric bike kits, DIY enthusiast, long distance commuters, and a general drive for value is raising the desire for more options for consumers, wanting speed for fun and function, while developing amnesia for the law. People want to ride their new ebikes, and have the same access to safe pathways as they did the week before on their 100% human bike. Rather than deal with the inevitable conflicts over access, behavior and perception within the general public, the typical user will try to blend in with the normal cycling community.
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers.  If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.  

This was the first ebike I ever bought. I've since become a builder and make my own. But this was a really reliable vehicle. I used it everyday for transportation. The company sent me any part I needed. It's got a power motor on it so it's super reliable. I wouldn't hesitate to buy this bike especially if you're new into the ebike world. If your looking to have some real fun buy this bike.. If your looking to meet new people buy this bike. If looking to go more green buy this bike. This bike is so much fun you well want to ride all day. This bike should be twice the price . I love love love it .

At just 36V and 5.2 Ah, the battery is not designed for long distance travel. GOTRAX claims the Shift S1 has a range of up to 15 miles (25 km), though that’s only with a lower pedal assist level. If you’re going full throttle, 10 miles (15 km) is a better estimate. But with a battery this small, you could easily charge it at your desk or in the corner of the classroom – lengthening your effective range.
An itinerant wordsmith with a broad constellation of interests, Lydia Chipman has turned iconoclasm into a livelihood of sorts. Bearing the scars and stripes of an uncommon diversity of experience -- with the notable exceptions of joining a religious order or becoming an artist -- she still can’t resist the temptation to learn something new. Lydia holds a master of arts in English from Georgia Southern University, and a bachelor of arts cum laude in integrative studies from Clayton College. Her expertise is in the areas of robotics, electronics, toys, and outdoors and computer equipment.
The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop.  They were among the early shops to embrace family friendly cargo bikes and  appreciated the role that electric would play in making cycling more broadly appealing.
Urban riding will never be the same, and cars will be in your way when you climb aboard the Specialized Turbo Vado 3.0. The zippy 28mph pedal-assist motor will leave you feeling invincible as you’re ripping along in turbo mode (which adds up to 320 percent of your power output). Although designed with female riders in mind—it comes with a women-specific saddle and grips, and a lower standover—the step-through frame is extremely convenient for anyone who doesn’t want to swing their leg over the back of a saddle while wearing street clothes. Slick, integrated lights, as well as fenders and a rear rack, add to the already-awesome features of this bike to make it the ideal combination of value, performance, and pep.

The Wavecrest Tidalforce M-750 was based on The original military experimental M-313 model. The M-313/M-750X was the first electric bike to be made and tested by Wavecrest Labs. It is based on a design developed for the Defense Advanced Research Projects Agency (DARPA) that was meant to allow zero-heat long distance troop movements for the United States Marine Corps in Afghanistan. The rear wheel in-hub motor and 36 volt/8ah front-hub battery were mounted onto a standard Montague Bicycles Paratrooper Bicycle frame. The 1000 watt rear hub motor had no set speed restriction, but was limited to about 25-32 (depending on load weight) MPH on a flat course. The distance the bike traveled on a single charge ranged from 15 miles (heavier load with no pedaling) to about 25 miles (vigorous assisted pedaling with less hill climbing).
If you are a regular bicyclist who wants to add some excitement to your rides or wants some help with those hills, a full sized electric bike is the way to go. If you are considering a bike as a means of transportation more than an outlet for amusement, then a smaller, folding electric bike is the convenient choice. In each category, consider the speed and range you want, as these factors impact price.
So first off, it isn’t fair to compare the power of a Chinese rear hub motor watt for watt with a 250W Bosch or Brose or even a Shimano or Yamaha mid-drive motor. There just isn’t even close to the amount of torque or power on a per watt basis and that’s before we get to controllers. However, comparing the Rattan’s 350W motor to the Ancheer’s 250W motor seems more proportionally correct. Where as I could make it about a third of the way up my driveway hill from a cold start on Ancheer throttle, I made it about 2/3rds of the way with the Rattan, or another 100 feet. On a flat surface, again with throttle only, I hit 20 mph in about 10 seconds with the Rattan. It takes me another 5+ seconds to get there on the Ancheer. One note, the battery gauge does bounce around a bit depending on how much it is working. At full throttle you might lose a bar or 2 only to get it back once you coast.

Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).

Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.


When I finally had the ability drive this thing in my city, it feels fantastic, you're cruising easily. But the minute it starts going up a hill, you also gotta peddle to help it go up. Which is okay because the little engine helps a lot so you're not straining yourself. But, being that the wheels are so small, after a while, you feel your legs get swore. I guess the size of the wheel
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an e-bike dubbed Zike.[9] The bicycle included NiCd batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial e-bikes were available.

To be honest, this bike is really designed for city commuters or kids riding around the suburbs. The fact that it’s foldable will let you carry it on the bus, on the train or even on the plane. It’s just not designed for heavy riding, long distances or tough terrains. If you want something sleek and fabulous at a fraction of the cost of most other e-bikes, this baby’s for you.


The battery is the pedelec’s power source. It supplies the motor with the electrical energy that is required to provide power assistance when cycling. So it is hardly surprising that there is frequent discussion and “talking shop” about the eBike’s battery in particular. What is the difference between batteries? How far can you go on a fully charged battery? What do you have to remember about storage? Thomas Raica, head of technical customer application, here provides information and advice.
In the Netherlands all train stations offer free bicycle parking, or a more secure parking place for a small fee, with the larger stations also offering bicycle repair shops. Cycling is so popular that the parking capacity may be exceeded, while in some places such as Delft the capacity is usually exceeded.[64] In Trondheim in Norway, the Trampe bicycle lift has been developed to encourage cyclists by giving assistance on a steep hill. Buses in many cities have bicycle carriers mounted on the front.
The bicycle's invention has had an enormous effect on society, both in terms of culture and of advancing modern industrial methods. Several components that eventually played a key role in the development of the automobile were initially invented for use in the bicycle, including ball bearings, pneumatic tires, chain-driven sprockets and tension-spoked wheels.[10]

Since 2000, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs) as a separate category, and which require no license to operate. PABs are currently defined as a two- or three-wheeled bicycle equipped with handlebars and operable pedals, an attached electric motor of 500W or less, and a maximum speed capability of 32 km/h from the motor over level ground. Other requirements include a permanently affixed label from the manufacturer in a conspicuous location stating the vehicle is a power-assisted bicycle under the statutory requirements in force at the time of manufacture.[14][15] All power-assisted bicycles must utilize an electric motor for assisted propulsion.


The pedals on a motorised bicycle must be the primary source of power for the vehicle. If the motor is the primary source of power then the device cannot be classed as a motorised bicycle. For example, a device where the rider can twist a throttle and complete a journey using motor power only without using the pedals, would not be classed as a motorised bicycle.
A response to an inquiry made to the Mass DOT/RMV indicates that Massachusetts does recognize the federal low speed electric bicycle Federal Law (15 U.S.C. § 2085) and interprets that to mean these ebikes do not require license or registration. However, some of the materials available on the RMV website do not distinguish between "Motorized Bicycle" and low power ebikes. One form, Bicycle Conversion to Motorized Bike, does document the exemption of low power ebikes.[100]

There are individuals who claim to have lost considerable amounts of weight by using an electric bike.[62] A recent prospective cohort study however found that people using e-bikes have a higher BMI.[63] By making the biking terrain less of an issue, people who wouldn't otherwise consider biking can use the electric assistance when needed and otherwise pedal as they are able.[64] This means people of lower fitness levels or who haven't cycled in many years can start enjoying the many health benefits E-bikes have to offer. [1]
Some electric bikes claim to use a neat trick called regenerative braking. If you start pedaling the bicycle or going downhill, the spinning wheels turn the electric motor in the hub in reverse and start charging up the batteries. In practice, regenerative braking is nowhere near as useful on an electric bicycle as it is on an electric train or car. An electric bike has much less mass and velocity than either a train or car, so it never gains (or loses) anything like as much kinetic energy when it starts and stops. You'd have to go down an awful lot of hills to charge up the batteries completely and that's usually not practical. And what's the point in pedaling the wheels simply to charge the battery? You might as well have bought an ordinary bicycle to start with!
There are generally two types of e-bike: throttle and pedal-assist. Throttle e-bikes, common among food delivery workers, don’t require any pedaling, just a twist of the handlebar to get moving. Wing’s e-bike is pedal-assist. The bike’s battery provides a boost while you pedal — up to 20 mph — but if you stop pedaling, the bike slows just like a regular bike.

There are individuals who claim to have lost considerable amounts of weight by using an electric bike.[62] A recent prospective cohort study however found that people using e-bikes have a higher BMI.[63] By making the biking terrain less of an issue, people who wouldn't otherwise consider biking can use the electric assistance when needed and otherwise pedal as they are able.[64] This means people of lower fitness levels or who haven't cycled in many years can start enjoying the many health benefits E-bikes have to offer. [1]


Power-assist: Also known as pedal-assist bikes, these are the bicycle equivalents of hybrid cars: they're designed to be pedaled quite a lot of the time and electrically powered either when you're tired or when you feel like a bit of electric help (when you're going up hill, for example). Unlike full-power bikes, they don't have hub motors; instead, there's a separate electric motor mounted near the rear wheel and driving it either through the gear sprocket or simply by pressing against the rear tire. Where a hub motor is difficult or impossible to pedal without any power (because you're effectively turning it into a generator), power-assist motors turn easily with little or no resistance when you pedal. That gives power-assist bikes much greater range than hub-motor ones (as much as 80–145km or 50–90 miles).
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
×