Experiments done in Uganda, Tanzania, and Sri Lanka on hundreds of households have shown that a bicycle can increase a poor family's income as much as 35%.[69][better source needed][70][71] Transport, if analyzed for the cost-benefit analysis for rural poverty alleviation, has given one of the best returns in this regard. For example, road investments in India were a staggering 3–10 times more effective than almost all other investments and subsidies in rural economy in the decade of the 1990s. What a road does at a macro level to increase transport, the bicycle supports at the micro level. The bicycle, in that sense, can be an important poverty-eradication tool in poor nations.
European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.
In 5 years of working as a bike messenger in Minneapolis, I've ridden all kinds of bikes, in all kinds of weather. I've ridden walmart mountain bikes, 80's classic steel road bikes, kitted out Treks, pretty much everything EXCEPT for fat tire bikes. Such wide tires always seemed... too much. No need for a bike that only makes itself worthwhile maybe two months out of the year, I thought.
Thanks for your feedback Joe! I personally find black on white to be high contrast and abrasive. Instead, this dark gray scheme is meant to be relaxing… but if it’s uncomfortable to you or difficult to read there are ways to change your browser and even your operating system to be more comfortable using the accessibility options. Here’s a list by device type and for some browsers https://goo.gl/voKTnW hope it helps!
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2 [123] as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.

Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! [14]

The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.

The Surly Big Easy is the Cadillac of the bike lane. The company’s new longtail e-cargo bike exudes a “they don’t make ’em like this anymore” stature, thanks to a beefed-up chromoly steel frame rolling on tough 26x2.5-inch tires. And because it’s a class 1 e-bike, you can actually ride it in the bike lane, too. The 7-foot-long, 67-pound bike won’t play well with your third-floor walk-up, so it’s best to think of it as a car supplement or replacement—that’s what Surly intended, anyway, as evidenced by the $5,000 price tag. However, if you’re ready to commit to the cargo bike life, you’ll struggle to find a stronger platform for achieving bike commuter nirvana.


What we especially love is how quiet this e bicycle is. If you’re riding down the street or through the park, the gentle hum of the motor is unnoticeable. This is because it’s hidden by the sound of your smooth pedaling. If you’re not into flashy gadgets, any ordinary person would assume you’re riding a conventional peddle bike. This is a great commuter bike.

The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead. 
In most jurisdictions, bicycles must have functioning front and rear lights when ridden after dark. As some generator or dynamo-driven lamps only operate while moving, rear reflectors are frequently also mandatory. Since a moving bicycle makes little noise, some countries insist that bicycles have a warning bell for use when approaching pedestrians, equestrians, and other cyclists, though sometimes a car horn can be used when a 12 volt battery is available.[citation needed]
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
But electric bicycles—e-bikes—are new territory for me. Broadly speaking, there are two basic options in e-bike land: power-on-demand and pedal-assist. With the former, the rider can control the speed with a throttle instead of just pedaling. Think moped but with an electric motor instead of internal combustion. Pedal-assist, by contrast, requires the rider to do some of the work. The electric motor won't engage unless the rider is pedaling.

Electric bikes are becoming a convenient and fun way to commute around a city, but they can be pricey. The average e-bike can cost $3,000, with some models getting up to $5,000 or more. But these prices are dropping, as new models come onto the market — and if you don’t mind giving up some of the glossier, high-tech features like embedded digital displays, retractable cable locks, and and theft tracking and recovery, you can find a really good quality e-bike for under $1,500.
Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles,[77] including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity.[78] A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.[79]

"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption, [59][60][61][62][63][64] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.


Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[43][44] Helmets are required.
In Manitoba Electric Bikes can be classified as a scooter or a moped/mobility vehicle depending on the power of the engine used and its top speed. If the engine on the Electric Bike is less than 50cc and it cannot exceed 50 km per hour the rider is not required to have a motorcycle licence or any specific training.[26] Electric Bikes can be driven by anyone with a Class 5 driver's licence in any stage of the graduated licensing process.[27] A Class 5 Learners Licence requires one to be age 16 (parents consent if under 18) and a visit to a licensing office to pass a vision test and a written knowledge test about the rules of the road and traffic signs.[28]
DIY enthusiasts, with tens of thousands of converted bikes using throttle-only, 20+ mph kits, are now officially labeled Moped class. While these bikes handle and pedal-ride just as safely as the class 3 speed pedelecs in many cases, our DIY counterparts will be officially kicked out and left on their own for advocacy and legal acceptance in California. This is a big deal, without a class sticker, any DIY electric bike conversion kit is considered a Moped and not a bicycle.
But if you're someone who loves riding, commutes to work on a bike, or has a gig that requires you to spend a lot of time in the saddle, you might want to look at electric bikes. You'll be able to go farther, faster, and expend less energy riding one. And if electric bikes are for you, look hard at the Cross E8 Step-Thru. It's an incredibly well-made, well-thought-out electric bike. Strip away the battery, motor, and computer, and you'd still be left with a really good cycle.
Attitudes to electric bikes have changed in recent years. For a long time they were seen by cyclists as 'cheating' and by non-cyclists as being just like a bike, but uglier and far more expensive. This new breed of best-in-class electric bikes feel more natural, look more normal, and people are coming around to the idea that a ride with the convenience of a bike but without all the sweat and effort is a Very Good Thing. 
In addition, we have a new lineup of torque sensors from NCTE to replace the long out-of-stock THUN devices. This restores the option for a true transducer that measures the actual spindle torsion. They provide an accurate human watts readout, and unlike other sensors they can be used in mid-drive setups where the motor is driving the right side chain.
"Motor-driven cycle" means any vehicle equipped with two or three wheels, a power source providing up to a maximum of two brake horsepower and having a maximum piston or rotor displacement of 50 cubic centimeters if a combustion engine is used, which will propel the vehicle, unassisted, at a speed not to exceed 30 miles per hour on a level road surface, which does not require clutching or shifting by the operator.[138] The designation is a replacement for "scooter" and "moped;"[139] Vermont doesn't seem to have laws specifically for e-bikes.[140]
And let’s not forget the economic advantages of owning an e-bike. The annual cost of running a new family car is, on average, about $9,000 per year. Running an electric bike costs around $400 per year. And while filling a gas tank costs around $30, recharging an electric bike battery costs only about 50 cents. A tank of gas may get you further, but not 60 times further!
Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an e-bike dubbed Zike.[9] The bicycle included NiCd batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial e-bikes were available.
I waited until I hit 100 miles on this beauty before writing this review. My riding buddies told me I couldn't get a quality ebike for under $3k. Absolutely the wrong advice. This Addmotor is amazing in every way. Well built, close attention to detail and a complete joy to ride. I would highly recommend this bike to anyone looking for a great ebike experience.
The entire drive system is neatly incorporated into the bike's design for optimal weight distribution and the ultimate in sexy design, while users control torque and power output, which peaks at a surprisingly punchy 530W, via a cool Mission Control App that can also be programmed to a time or distance parameter to ensure there's enough power to get you home.
Some electric bikes claim to use a neat trick called regenerative braking. If you start pedaling the bicycle or going downhill, the spinning wheels turn the electric motor in the hub in reverse and start charging up the batteries. In practice, regenerative braking is nowhere near as useful on an electric bicycle as it is on an electric train or car. An electric bike has much less mass and velocity than either a train or car, so it never gains (or loses) anything like as much kinetic energy when it starts and stops. You'd have to go down an awful lot of hills to charge up the batteries completely and that's usually not practical. And what's the point in pedaling the wheels simply to charge the battery? You might as well have bought an ordinary bicycle to start with!
Some power-on-demand only e-bikes can hardly be confused with, let alone categorised as, bicycles. For example, the Noped is a term used by the Ministry of Transportation of Ontario for e-bikes which do not have pedals or in which the pedals have been removed from their motorised bicycle. These are better categorised as electric mopeds or electric motorcycles.
Another big upgrade here is the 36V battery. Instead of the 8Ah that the Ancheer had, Rattan has a 10.4Ah battery. The battery actually looks a lot like this one that goes for $190 on ebay or a little more on Amazon. Rattan tells me it is full of genuine LG cells which seem to perform quite well. On cold days, my 15 km (10 mile) very hilly commute would use up about half of the battery (Ancheer would be dying on the way back home). I imagine someone significantly under my 200+lbs could approach the 25 miles Rattan says you can get on throttle alone or up to 50 miles of pedal assist. I’ll just say it was significantly more than the Ancheer.

With a chain drive transmission, a chainring attached to a crank drives the chain, which in turn rotates the rear wheel via the rear sprocket(s) (cassette or freewheel). There are four gearing options: two-speed hub gear integrated with chain ring, up to 3 chain rings, up to 11 sprockets, hub gear built into rear wheel (3-speed to 14-speed). The most common options are either a rear hub or multiple chain rings combined with multiple sprockets (other combinations of options are possible but less common).
Most consumers want an e-bike that will accommodate its motor without being too cumbersome and will remain stable in spite of its electronic components. Some consumers want only the most basic of e-bike features, including lights, a cargo rack/basket, and a water bottle holder. Others are focused more heavily on safety features, such as brake type. And still others are concerned with convenience and portability.
And the last product update to kick off the year is the pilot release of our new Baserunner motor controller. We spent much of last summer and fall trying to cram an even more miniature version of the Phaserunner into compact profile that could fit inside the controller cavity of the popular Hailong downtube battery cradles, and by golly we did it. While not as powerful as the Phaserunner (just 55A max phase current, and 60V max battery voltage), the Baserunner is perfectly suited to the smaller geared and direct drive hub motors using the Higo Z910 plug. This allows for a very tidy installation with no separate controller to mount.
During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.
Übrige "Motorfahrräder": “E-Bikes mit einer Leistung zwischen 500 und 1000 Watt oder einer bauartbedingten Höchstgeschwindigkeit von 20 bis 30 km/h oder einer Tretunterstützung, die auch bei einem Tempo von 25 – 45 km/h wirkt, gelten als Motorfahrräder und benötigen ein entsprechendes Kontrollschild.”. You can use any bicyle path and also hiking roads forbidden to motorbikes if you drive slowly.
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170-pound rider when powered only by that engine.[106]
IZIP ebikes is currently holding their huge annual sale. We know that IZIP makes high quality electric bikes that you can buy and ride with confidence. The current sale is a clearance of their 2018 models. One of the best ways to get a good deal on any bike is to buy a previous year’s model. Plus, IZIP offers free same-day shipping. So we have highlighted two of the best bargains in ebikes available from IZIP right now.
As with all these bikes, the assisted speed is capped at 15mph, but unlike some of them, the Gtech eBike City or its identical (spec-wise) sibling the eBike Sport (this just has a standard frame rather than a step-through one) is light and agile enough for you to be able pedal harder without feeling like the weight is fighting you back down to 15mph. You can even, at a push, use it without the motor on flatter roads.

I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have

Most European bike rules are tight and restrictive. Right now the California state ebike rules in AB 1096 provide the clearest and cleanest format, and they support ebike riding. No other U.S. regulations come close. The big brand ebikes (Giant, Specialized, Trek) are selling bikes that fit within European rules (250w-300w motors). This gives them economies of scale.
This is a virtual hello to all the people who came by our booth last weekend at the BC Bike Show and are just now visiting our webpage for the first time. We had a great time and were delighted to see how much this event has grown recently. (And to those who lament that the bike show is now totally taken over by ebikes, well it's been over 15 years now that we've been trying to tell you all this day was coming!)
At first glance, Wing’s e-bikes share some design features with Dutch e-bike company VanMoof’s flagship bikes, most noticeably the elongated top tube (23.3 inches) with embedded front and rear lights. There are differences — VanMoof’s battery is embedded in the frame, while Wing’s is external — but to look at them side-by-side, one could easily conclude that Wing is just a less-expensive version of the VanMoof.
All classes of electric-assisted bicycles may be operated on a fully controlled limited access highway. Class 1 and 2 electric bicycles can be used on sidewalks, but Class 3 bicycles "may not be used on a sidewalk unless there is no alternative to travel over a sidewalk as part of a bicycle or pedestrian path."[143] Generally a person may not operate an electric-assisted bicycle on a trail that is designated as non-motorized and that has a natural surface, unless otherwise authorized.
Electric bicycles use batteries as a source of power and a quiet DC motor as a driving mechanism. On most e-bikes the motor is built directly into the wheel (known as a hub motor) and the batteries are discreetly hidden in the rear rack or frame. Electric bikes can be operated just like normal bicycles, but they can also be power-driven by a throttle or pedaled with the help of pedal-assist (PAS or pedelec).
Indian law requires that all electric vehicles have ARAI[50] approval. Vehicles with below 250W and speed less than 30 km/h, do not require certification- hence not following full testing process, but needs to get exemption report from ARAI. Whereas more powerful vehicles need to go through a full testing process following CMVR rules. This can take time and cost money but assures safe and reliable design for Electric Vehicles. These regulations are not promulgated by the Regional Transport offices, and riders are not required to obtain a licence to drive, to carry insurance, or to wear a helmet.
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.
Oklahoma defines an Electric-Assisted Bicycle in 47 O.S. 1-104 [122] as "Two or three wheels; and Fully operative pedals for human propulsion and equipped with an electric motor with a power output not to exceed one thousand (1,000) watts, incapable of propelling the device at a speed of more than thirty (30) miles per hour on level ground, and incapable of further increasing the speed of the device when human power alone is used to propel the device at a speed of thirty (30) miles per hour or more. An electric-assisted bicycle shall meet the requirements of the Federal Motor Vehicle Safety Standards as set forth in federal regulations and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied."
From all the Chinese brands that have come and disappeared, Onway is still standing strong. That means that they have sold enough bikes, and they have been tried and tested enough for customers to know what to expect. So, what can you expect from this Onway bike? Well, for a very affordable price, you will get anything you realistically need in an e-bike – multi-purpose tires for various terrains, LCD display, LED headlights, taillights, a kickstand… Overall build quality and quality of the parts is above average, but there are some things that you will need to change, and seat should be the first on the list. Customer support is not that great, but if you decide to purchase this bike you will get a fun bike, for affordable price that you will be able to assemble and ride in no time.
None of this would matter if the VanMoof Electrified S2 (and its close relative the X2) wasn't fun to ride, but it is a blast. Like the Brompton, it pulls off the neat trick of powering you along but giving the illusion that you're doing the work, reacting quickly and cleverly to the speed of your pedalling and the difficulty of any incline you're on. 
Available products (motors, senors, batteries, control systems. etc.) change fast since the e-bike market shows a strong growth. In principle, get a rear motor if you want a lot of raw power and acceleration (e.g. for a 500W motor). Middle motors are more energy efficient and less subject to problems (e.g. overheating). Middle motors usually are combined with integrated rear hub gears, and rear motors with derailleurs. Both have advantages and disadvantages. E.g. the former require less maintenance, are easy to use in go-and-stop traffic, but require taking off weight on pedals when shifting. Therefore the latter (derailleurs) are better for speedy overland and hills cycling.
There are many possible types of electric motorized bicycles with several technologies available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. The power levels of motors used are influenced by available legal categories and are often limited to under 750 watts.
State and Local Laws dictate your use, but cannot constitutionally supersede the federal law – Any ebike purchased within the 750W/20mph limits has no fear of being under federal motor vehicle classification, nor can any state classify them a motor vehicle. The ebike is considered a ‘bicycle’ for consumer purposes. However, the State Laws on local bike paths and local thruways may prohibit or limit ebike access. When bike path signs use word such as ‘motor vehicles’ and ‘motorbikes’ , the laws are likely referring to gas-ICE motorbikes/dirt bikes/scooters, and not ebikes. Other references to ‘motorized bicycles’ or ‘motorized vehicles’ sound more inclusive and probably are intended for either ebikes or gas mopeds. If in doubt, you always have the option to pedal unassisted by completely powering your bike down. Even though Federal law grant ebikes a bicycle status, the common consensus found in my research allows local and state law to add additional regulation to pathway and road access, just because “it has a motor”. So the Federal laws protects the consumer from the burden of motor vehicle requirements, but not the restrictions to local and state right of ways enjoyed by all non-motored bicycles.
European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.

Electric bikes vary widely in price, anywhere from $999 to $2000+, so you’ll have to determine how important certain features are to the overall cost. (However, we made a list of electric bikes under $1.000 here.)The battery used to power an electric bike motor is a key factor in how expensive a particular bike is. In general, the more miles a battery can provide, the more expensive it will be, so it’s important to consider the type of riding you plan on doing. If you know you’ll be using predominantly motor-generated power, then paying a bit more for a battery with a longer range is probably a good idea. Alongside with a good quality battery, motor is the most expensive part of an electric bike. Most standard electric bike motors come with a power rating of 250W, and the industry standard in the US is 500W. Maximum power of the motor you can legally use in the US is 750W. The non-electric components used on an electric bike are almost the same with those used on the conventional bicycles. The quality of the components used will affect the maintenance costs of your electric bike down the road, and more quality components mean higher upfront cost. Lastly, there is the frame. Since the frame is basically the skeleton of your electric bike, it’s wise to select a good material that will be the optimum combination of weight and durability.


Some argue, that an ebike should have some kind of front suspension, i.e. be able to cope with potholes at higher speed or off-road conditions. However, in countries with flat roads (e.g. Switzerland, Germany or Holland) you don't need that extra weight for extra price if you stay on roads and/or drive slowly in difficult terrain. Some makes (like the Stromer) let you choose.
An e-bike is identified as a "motor assisted cycle" (MAC) in British Columbia, which differs from electric mopeds and scooters, which are "limited-speed motorcycles." Motor assisted cycles must: have an electric motor of no more than 500 W; have fully operable pedals; not be capable of propelling the device at a speed greater than 32 km/hr [19.9 mph]. The engine must disengage when (a) the operator stops pedaling, (b) an accelerator controller is released, OR (c) a brake is applied. A driver's license, vehicle registration, and insurance are all not required. A bike helmet must be worn.[22]

The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]

×