The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
Ebike definition in Colorado follows the HR 727 National Law: Template:Convert e-power and Template:Convert max, 2 or 3 wheels, pedals that work. Legal low powered Ebikes are allowed on roads and bike lanes unless the city or county has passed laws to the contrary (Boulder city bans ebikes over 400W from bike lanes and all ebikes from bike paths) -none -(except Boulder city) have to date. Bicycles and Ebikes are disallowed on certain high speed highways and all Interstates unless signed as "Allowed" in certain rural Interstate stretches where the Interstate is the ONLY means of travel. [35] Unless the locality has specifically passed laws making ebikes illegal on sidewalks or trails, Ebikes are legal. However most business and shopping districts do not allow riding bikes or ebikes on sidewalks. Boulder and a few other cities specifically dis-allow ebikes on their trail systems through legal statute.
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
"Motor-driven cycle" means any vehicle equipped with two or three wheels, a power source providing up to a maximum of two brake horsepower and having a maximum piston or rotor displacement of 50 cubic centimeters if a combustion engine is used, which will propel the vehicle, unassisted, at a speed not to exceed 30 miles per hour on a level road surface, which does not require clutching or shifting by the operator.[138] The designation is a replacement for "scooter" and "moped;"[139] Vermont doesn't seem to have laws specifically for e-bikes.[140]
Tires vary enormously depending on their intended purpose. Road bicycles use tires 18 to 25 millimeters wide, most often completely smooth, or slick, and inflated to high pressure in order to roll fast on smooth surfaces. Off-road tires are usually between 38 and 64 mm (1.5 and 2.5 in) wide, and have treads for gripping in muddy conditions or metal studs for ice.

I bought this bike from a dealer after extensive research on ebikes. The Elby is on par with European commuter ebikes at a better price point, you get a lot for your $ here. Elby is the complete package commuter: lights & a USB charger (for a phone or whatever) are integrated into the motor’s power supply and wired inside the frame. Rugged fenders have heavy-duty cross braces to attach baskets and whatnot. Thick Continental tires make for a comfy ride. The step-through frame is very convenient, built stout enough to carry me (200#) and two loaded baskets down hills and around curves with perfect stability. The motor on this bike is in the rear hub, and having it behind me makes it virtually soundless. The motor (BionX 500 watt) kicks in as soon as you start pedaling, but there is a
Oregon Law (ORS 801.258]) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed greater than 20 miles per hour on level ground.[124]

Controllers for brushed motors: Brushed motors are also used in e-bikes but are becoming less common due to their intrinsic lower efficiency. Controllers for brushed motors however are much simpler and cheaper due to the fact they don't require hall sensor feedback and are typically designed to be open-loop controllers. Some controllers can handle multiple voltages.


Solar Shunt firmware: With this firmware the Cycle Analyst can use the auxilliary input as a second current sensor for measuring and showing the solar amps and watts. You can not only see in realtime how much solar power is coming into the pack, you also get combined statistics such as the %solar recharge and the net wh/km mileage taking into account the solar input for the day. This is the ideal instrument for looking at solar ebike performance, consolodating all measurements in a single device.

I did my commute a few times with the Rattan and while I would never give up my “bike store” e-bike for this, it was a worthy substitute. It never gave out on the big hills, nor did I have to brake because I felt the bike was falling apart. The frame is a little small for 6-foot me but it only comes in one size. I really miss the low rolling drag of having road tires however and this is something that both Rattan and Ancheer could improve upon. I don’t think many people are seriously off-roading with these bikes. Put some Schwalbe Big Bens on there!
Earlier UK regulations required that the motor has an average power output limited to 200 W (250 W for tricycles and tandems) and weight limited to 40 kg (60 kg for tricycles and tandems). These regulations must come in-line with the EU regulations by (find deadline). For models sold before June 2003, e-bikes conforming to the speed, weight and power limits may also be considered pedal cycles. Electric bikes with higher power outputs, or those not meeting the "pedelec" definition are now treated as motorcycles and require a license.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]
Motor-driven cycles may be operated on the roadway without registration, but the operator must have a driver's license.[85] The cycle may not be operated on any sidewalk, limited access highway or turnpike. If the maximum speed of the cycle is less than the speed limit of the road, the cycle must operate in the right hand lane available for traffic or upon a usable shoulder on the right side of the road unless the operator is making a left turn.
In 5 years of working as a bike messenger in Minneapolis, I've ridden all kinds of bikes, in all kinds of weather. I've ridden walmart mountain bikes, 80's classic steel road bikes, kitted out Treks, pretty much everything EXCEPT for fat tire bikes. Such wide tires always seemed... too much. No need for a bike that only makes itself worthwhile maybe two months out of the year, I thought.
This Class 3 (28 mph), utilitarian, road e-bike is smooth and torquey thanks to its Bosch Performance Speed motor. With a drop bar and traditional road-bike position and handling, the CrossRip+ is more suited to longer rides on mixed terrain than navigating congested city streets. It comes with a rear rack—for mounting bags, not for attaching cargo directly—full fenders, a kickstand, and integrated front and rear lights (which are powered by a Bosch 500Wh battery). It features a SRAM Force 1x11 drivetrain, hydraulic disc brakes, and wide 700x38mm tires.
It appears Tennessee has not passed any legislation that applies to electric bicycles. Some people think the laws pertaining to a Motorized Bicycle should be used for an electric bicycle. However, a Motorized bicycle would be a gasoline powered device per state law as it is defined as "means a vehicle with two (2) or three (3) wheels, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters (50cc) which produces no more than two (2) brake horsepower and is capable of propelling the vehicle at a maximum design speed of no more than thirty miles per hour (30 mph) on level ground." [56] 

China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008,[72] and reaching an estimated fleet of 120 million e-bikes in early 2010.[2][73] This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities.[72] Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car.[2] Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007.[73] By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.[72][73]
Speed Pedelec ebikes – A new classification of bikes called ‘Speed Pedelecs’ have emerged which technically meet the bicycle definition for a 20 mph ebike. These ebikes are designed to max out at 28 mph. Pedelecs are pedal activated vs throttle activated. The weasel words within the definition says, “20mph on motor alone”. Thus, a person who adds their leg power to the motor assist and happens to cruise at 28mph is NOT doing it by motor alone, and therefore the bike is considered to be compliant with the Federal Law. If the rider stops pedaling, the speed pedelec cannot maintain speed. Speed Pedelecs are becoming more popular in Europe and America, which means more models are being offered.
The safety bicycle gave women unprecedented mobility, contributing to their emancipation in Western nations. As bicycles became safer and cheaper, more women had access to the personal freedom that bicycles embodied, and so the bicycle came to symbolize the New Woman of the late 19th century, especially in Britain and the United States.[8][73] The bicycle craze in the 1890s also led to a movement for so-called rational dress, which helped liberate women from corsets and ankle-length skirts and other restrictive garments, substituting the then-shocking bloomers.[8]
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
Photo: Could solar power be the future of electric bicycles? The large solar panel mounted over the back wheel of this experimental bike powers an electric motor connected by a chain drive to the back wheel, helping the rider when he doesn't feel like pedaling. Using clean, green solar power would remove the problem of having to charge electric bikes with electricity generated from fossil fuels—and help to extend their range significantly. Photo by Warren Gretz courtesy of US DOE/NREL.
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
Uniparts eyeing overseas acquisition to expand hydraulic cylinder biz / Maruti Suzuki launches new Alto with BS VI engine; price starts at Rs 2.93 lakh / Top 10 selling two-wheelers in FY19: Honda Activa retains the top spot / KPIT Tech back on exchanges, scrip races to ₹105 / Maruti Suzuki doubles market share in LCV goods carrier segment in FY'19 / Mercedes-Benz partners the first-ever international esport competition ‘ESL One’ in India / Audi opens service facility in Vijayawada / KPIT Technologies gets listed on BSE and NSE / Honda launches new CBR650R at Rs 7.7 lakh / Hiroshi Ii joins JTEKT India as new chairman

Saddles also vary with rider preference, from the cushioned ones favored by short-distance riders to narrower saddles which allow more room for leg swings. Comfort depends on riding position. With comfort bikes and hybrids, cyclists sit high over the seat, their weight directed down onto the saddle, such that a wider and more cushioned saddle is preferable. For racing bikes where the rider is bent over, weight is more evenly distributed between the handlebars and saddle, the hips are flexed, and a narrower and harder saddle is more efficient. Differing saddle designs exist for male and female cyclists, accommodating the genders' differing anatomies and sit bone width measurements, although bikes typically are sold with saddles most appropriate for men. Suspension seat posts and seat springs provide comfort by absorbing shock but can add to the overall weight of the bicycle.
Visually, the Pedego City Commuter Classic Electric Bike is stunning – a smart blend of yesteryear's style and today's technology. Pleasantly high handlebars, a sprung seat, and lovely Schwalbe Fat Frank tires make it very comfortable. Stopping is taken care of by powerful disk brakes, front and rear. Lights are included, as is a useful cargo rack. From an e-bike standpoint, the Pedego Classic City Commuter sports a reliable, hub-mounted motor driven by a 36-volt, 10-amp battery. There's a digital display with a trip computer, odometer, speedometer, pedal assist level, and battery charge information.

One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.

Firstly there's a magnetically-fired locking pin in the rear wheel, triggered by kicking a button on the hub. This is fairly secure in itself and almost impossible to remove without destroying the bike. In London, we'd pair it with a more traditional bike lock so there's a more obvious visual deterrent, though a LED matrix screen on the frame does issue a warning to would-be tea-leafs.
Bicycle shall mean (1) every device propelled solely by human power, upon which any person may ride, and having two tandem wheels either of which is more than fourteen inches in diameter or (2) a device with two or three wheels, fully operative pedals for propulsion by human power, and an electric motor with a capacity not exceeding seven hundred fifty watts which produces no more than one brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than twenty miles per hour on level ground.
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.
×