Arkansas does not define E-bikes. The following definition describes a combustion engine. E-bikes being electric do not have a cylinder capacity and thus this law is not technically applicable. The state defines a "Motorized bicycle" as "a bicycle with an automatic transmission and a motor of less than 50cc." Riders require either a certificate to operate a motorized bicycle, a motorcycle license, a motor-driven cycle license, or a license of class A, B, C or D. Certificates cannot be issued to riders under 10 years of age.
Template:Cleanup Template:Split Many countries have Electric bicycle laws which legislated to one extent or another the legality of Electric Bicycles. Countries Like the United States and Canada have Federal regulations governing the safety requirements and standards of manufacture. Other countries like the Signatories of the European Union have agreed to wider ranging legislation covering use and safety for what they term EPAC(Electric pedal assisted cycles).
Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
UPDATE (2019-03-15): I've now got more than 110 miles on the bike and still loving it. The longest ride I did was 28.5 miles and the display was still showing about two bars left on the battery. But the battery gauge is not accurate. Even when it went down to two bars it would also jump back up to 4 bars and stay that way for awhile. So it's really hard to tell how much power you have left. On one ride, after 14 miles the pedal assist stopped working all of a sudden. I stopped and re-seated the cadence sensor and it started working again. Even when PAS didn't work the throttle was still working. It hasn't happened since. There was also a lot of rattling noises which I found was the battery rattling around in the mounting bracket.
Speaking of which, if you're used to non-electric cycles, be aware that e-bikes are heavy and capped at 25kph or 15.5mph. In many cases, that means the bike starts to feel like its actively fighting against you, if you try to push the speed higher than that by pedalling. That's especially true with heavier bikes, for obvious reasons, and can take a while to get used to.
In China, e-bikes currently come under the same classification as bicycles and hence don't require a driver's license to operate. Previously it was required that users registered their bike in order to be recovered if stolen, although this has recently been abolished. Due to a recent rise in electric-bicycle-related accidents, caused mostly by inexperienced riders who ride on the wrong side of the road, run red lights, don't use headlights at night etc., the Chinese government plans to change the legal status of illegal bicycles so that vehicles with an unladen weight of 20 kg (44 lb) or more and a top speed of 30 km/h (19 mph) or more will require a motorcycle license to operate, while vehicles lighter than 20 kg (44 lb) and slower than 30 km/h can be ridden unlicensed. In the southern Chinese cities of Guangzhou, Dongguan and Shenzhen, e-bikes, like all motorcycles, are banned from certain downtown districts. There are also bans in place in small areas of Shanghai, Hangzhou and Beijing. Bans of "Scooter-Style Electric Bikes" (SSEB) were however cancelled and in Shenzhen e-bikes may be seen on the streets nowadays (2010–11).
One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.
Not all e-bikes take the form of conventional push-bikes with an incorporated motor, such as the Cytronex bicycles which use a small battery disguised as a water bottle. Some are designed to take the appearance of low capacity motorcycles, but smaller in size and consisting of an electric motor rather than a petrol engine. For example, the Sakura e-bike incorporates a 200 W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one.
But if you're someone who loves riding, commutes to work on a bike, or has a gig that requires you to spend a lot of time in the saddle, you might want to look at electric bikes. You'll be able to go farther, faster, and expend less energy riding one. And if electric bikes are for you, look hard at the Cross E8 Step-Thru. It's an incredibly well-made, well-thought-out electric bike. Strip away the battery, motor, and computer, and you'd still be left with a really good cycle.
Tires vary enormously depending on their intended purpose. Road bicycles use tires 18 to 25 millimeters wide, most often completely smooth, or slick, and inflated to high pressure in order to roll fast on smooth surfaces. Off-road tires are usually between 38 and 64 mm (1.5 and 2.5 in) wide, and have treads for gripping in muddy conditions or metal studs for ice.
Some US companies, notably in the tech sector, are developing both innovative cycle designs and cycle-friendliness in the workplace. Foursquare, whose CEO Dennis Crowley "pedaled to pitch meetings ... [when he] was raising money from venture capitalists" on a two-wheeler, chose a new location for its New York headquarters "based on where biking would be easy". Parking in the office was also integral to HQ planning. Mitchell Moss, who runs the Rudin Center for Transportation Policy & Management at New York University, said in 2012: "Biking has become the mode of choice for the educated high tech worker".
If you are a regular bicyclist who wants to add some excitement to your rides or wants some help with those hills, a full sized electric bike is the way to go. If you are considering a bike as a means of transportation more than an outlet for amusement, then a smaller, folding electric bike is the convenient choice. In each category, consider the speed and range you want, as these factors impact price.
In conformance with legislation adopted by the U.S. Congress defining this category of electric-power bicycle (15 U.S.C. 2085(b)), CPSC rules stipulate that low speed electric bicycles (to include two- and three-wheel vehicles) are exempt from classification as motor vehicles providing they have fully operable pedals, an electric motor of less than 750W (1 hp), and a top motor-powered speed of less than 20 miles per hour (32 km/h) when operated by a rider weighing 170 pounds. An electric bike remaining within these specifications is subject to the CPSC consumer product regulations for a bicycle. Commercially manufactured e-bikes exceeding these power and speed limits are regulated by the federal DOT and NHTSA as motor vehicles, and must meet additional safety requirements. The legislation enacting this amendment to the CPSC is also known as HR 727. The text of HR 727 includes the statement: "This section shall supersede any State law or requirement with respect to low-speed electric bicycles to the extent that such State law or requirement is more stringent than the Federal law or requirements." (Note that this refers to consumer product regulations enacted under the Consumer Product Safety Act. Preemption of more stringent state consumer product regulations does not limit State authority to regulate the use of electric bicycles, or bicycles in general, under state vehicle codes.)
The electric bike revolution has officially crossed into the arena of off-road motorbikes. For those who prefer riding in nature, Cake introduced a product which not only respects the environment but other riders, as well. Cake’s Kalk is a silent off-road motorbike that releases no emissions into the atmosphere. Additionally, its electric motor means no gear changing or clutching — a silent motorbike that won’t detract from the experience of others. Perhaps the best part is Cake avoided any sacrifice in performance. The Kalk reaches speeds of fifty miles per hour and features three distinct driving modes: Discover, Explore, and Excite.
That aside, the Axis is a fantastic e-bike. At 'only' 16kg, it's almost lively by e-bike standards, but it also feels rock solid. It's geared too low in my opinion – I think it's fair to say I am not the target market – but in 8th, you can breeze on past the legally mandated, electrically-assisted 15.5mph. The hydraulic disk brakes will then bring you to a pleasingly rapid dead stop. The range and charging time are good, too. Cheap it is not, mind you.
Bicycles and horse buggies were the two mainstays of private transportation just prior to the automobile, and the grading of smooth roads in the late 19th century was stimulated by the widespread advertising, production, and use of these devices. More than 1 billion bicycles have been manufactured worldwide as of the early 21st century. Bicycles are the most common vehicle of any kind in the world, and the most numerous model of any kind of vehicle, whether human-powered or motor vehicle, is the Chinese Flying Pigeon, with numbers exceeding 500 million. The next most numerous vehicle, the Honda Super Cub motorcycle, has more than 60 million units made, while most produced car, the Toyota Corolla, has reached 35 million and counting.
You are not allowed to drive S-Pedelecs in France even if they are registered legally in your country (e.g. Germany or Switzerland). In other words, if you plan to take your 45h bike that is legal in your country on vacation in another where it is not, you may violate traffic law. Remove the license plate or don't do it. People who commute between countries, are known to hack removable plates with magnets ...
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.
To be honest, this bike is really designed for city commuters or kids riding around the suburbs. The fact that it’s foldable will let you carry it on the bus, on the train or even on the plane. It’s just not designed for heavy riding, long distances or tough terrains. If you want something sleek and fabulous at a fraction of the cost of most other e-bikes, this baby’s for you.
Regulations appear to deal with Bicycles with helper motors. No person shall ride a bicycle with a helper motor unless that person holds a valid motor vehicle operator's license. No person shall operate a bicycle with a helper motor at a rate of speed exceeding thirty miles per hour; nor shall any bicycle with a helper motor be operated on any sidewalk, limited access highway or turnpike. Driver's licence is required except if a special permit is obtained by havnig a doctor fill out a certificate and shows they are able to drive the bike with and without the motor assisting.
Bicycle includes all vehicles propelled by the person riding the same by foot or hand power or a helper motor; and (3) "helper motor" means a motor having a capacity of less than fifty cubic centimeters piston displacement, rated not more than two brake horsepower, capable of a maximum speed of no more than thirty miles per hour and equipped with automatic transmission. Local jurisdictions can pass law at variance with the state law.
Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.
Let’s face it – Commuting can be a nightmare. Seemingly infinite price hikes, delays to trains, crammed tubes and congested roads dominate the ways of getting to work. The commuter misery is real. But, what if you could transform this part of the day from a chore to a pleasure? Enter the eBike. The clean, … Continue reading Why an eBike is so good for commuting
Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles, including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity. A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.
Introduction A quick of note of my experiences riding a Moustache Dimanche eBike, kindly provided by Fully Charged, on a spectacular 4 day trip, coast-to-coast across Italy. Overall, an amazing experience in terms of the quality of the ride, the scenery and the new experience of quite painless climbing of the many steep hills. I … Continue reading The joys of crossing Italy coast 2 coast on an eBike – by Andreas Credé
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
This was the first ebike I ever bought. I've since become a builder and make my own. But this was a really reliable vehicle. I used it everyday for transportation. The company sent me any part I needed. It's got a power motor on it so it's super reliable. I wouldn't hesitate to buy this bike especially if you're new into the ebike world. If your looking to have some real fun buy this bike.. If your looking to meet new people buy this bike. If looking to go more green buy this bike. This bike is so much fun you well want to ride all day. This bike should be twice the price . I love love love it .
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and completely legal in Canada since early 2001. In November 2005 "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4 2006 the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario. 
I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
Some countries require child and/or adult cyclists to wear helmets, as this may protect riders from head trauma. Countries which require adult cyclists to wear helmets include Spain, New Zealand and Australia. Mandatory helmet wearing is one of the most controversial topics in the cycling world, with proponents arguing that it reduces head injuries and thus is an acceptable requirement, while opponents argue that by making cycling seem more dangerous and cumbersome, it reduces cyclist numbers on the streets, creating an overall negative health effect (fewer people cycling for their own health, and the remaining cyclists being more exposed through a reversed safety in numbers effect).