In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.

Since 2001, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs). They are currently defined as a two or three wheeled bicycle with an attached electric motor of 500W or less and which is capable of being propelled manually. Furthermore to meet the safety requirements set down by this legislation it must meet the following; when engaged by muscular power it must cease assistance when muscular power ceases or if powered by an accelerator controller cease power when braking and be incapable of providing assistance above 32 km/h and bear a label that is permanently affixed by the manufacturer and appears in a conspicuous location stating the vehicle is a power-assisted bicycle.[5][6]


"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,[133][134][135][136][137] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.


The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].
eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …
In 2012, two e-bike advocates completed the first 4,000-mile (6,400 km) transcontinental e-bike tour from New York to San Francisco to advocate for e-bikes in major cities across the U.S.[81] Pedego Electric Bikes is the best selling brand in the U.S. Many e-bikes in the United States are standard bicycles converted using a kit. In general, the kits include the motor (the majority of which are hub motors built into the front or rear wheel), a speed controller, throttle (usually twist-grip or thumb throttle), necessary wiring and connectors, and a battery. Several U.S. companies offer conversion kits which also offer advanced lithium battery packs. Major manufacturers also offer complete e-bikes. Trek offers a line of e-bikes using the Bionx system in which the rider programs the controller to determine how much effort the motor will give in response to rider effort, from 25% up to 200% of the rider's power. This system ensures a minimum level of rider participation and is also used to comply with many European laws mandating partial human effort before the motor engages.
We are kicking off this series with a quick look at Keith Forbes. Keith showed up unannounced at our shop a year and a half ago, asking if there may be any work opportunities as he was considering a move to Vancouver from Trinidad and had something of a personal interest in transportation technology. We'll let the video show what he's been up to since then!
The last 8 months we've been wrapping up some long duration testing of Statorade across different hub motor lines and performing experiments confirming its long term stability. These results have us pumped to introduce this motor cooling solution beyond DIY'ers and into wider markets. As an example, have a look at the video we below showing the effect this has on a small direct drive folding bike motor.

The 1968 Vienna Convention on Road Traffic of the United Nations considers a bicycle to be a vehicle, and a person controlling a bicycle (whether actually riding or not) is considered an operator. The traffic codes of many countries reflect these definitions and demand that a bicycle satisfy certain legal requirements before it can be used on public roads. In many jurisdictions, it is an offense to use a bicycle that is not in a roadworthy condition.[citation needed]


The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead. 
Addmotor MOTAN 1000W Electric Bicycle 14.5Ah Lithium Battery Electric Bike 26 Inch Fat Tire Ebike Front Fork Suspension Mountain Beach Snow Pedal Assist M-5500 for Adults Men (Black) Price: $2,699.00 BUY NOW ON AMAZON Full Disclosure: We earn a commission if you click this link and make a purchase, at no additional cost to you. Last Updated: 01/02/2019
Some US companies, notably in the tech sector, are developing both innovative cycle designs and cycle-friendliness in the workplace. Foursquare, whose CEO Dennis Crowley "pedaled to pitch meetings ... [when he] was raising money from venture capitalists" on a two-wheeler, chose a new location for its New York headquarters "based on where biking would be easy". Parking in the office was also integral to HQ planning. Mitchell Moss, who runs the Rudin Center for Transportation Policy & Management at New York University, said in 2012: "Biking has become the mode of choice for the educated high tech worker".[66]
During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.
Many newer or smaller companies only design and market their products; the actual production is done by Asian companies. For example, some 60% of the world's bicycles are now being made in China. Despite this shift in production, as nations such as China and India become more wealthy, their own use of bicycles has declined due to the increasing affordability of cars and motorcycles.[102] One of the major reasons for the proliferation of Chinese-made bicycles in foreign markets is the lower cost of labor in China.[103]
By 1898 a rear wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel was patented by Mathew J. Steffens. Also, the 1899 Template:US Patent by John Schnepf depicted a rear wheel friction “roller-wheel” style drive electric bicycle.[5] Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his Template:US Patent. Wood’s device used 4 fractional horsepower motors; each rated less than ½ horsepower and connected through a series of gears.[6]
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
A new European product safety standard EN 15194 will be published in 2009. EN 15194 contains several new requirements for ebikes to be sold in European Union and European Economic Area, including weight and voltage limitations. EN 15194 also defines a specific name for EU approved electrically-assisted cycles, EPAC - "Electrically Pedal Assisted Cycle".
Template:Cleanup Template:Split Many countries have Electric bicycle laws which legislated to one extent or another the legality of Electric Bicycles. Countries Like the United States and Canada have Federal regulations governing the safety requirements and standards of manufacture. Other countries like the Signatories of the European Union have agreed to wider ranging legislation covering use and safety for what they term EPAC(Electric pedal assisted cycles).
Riding position: You also may wish to check out an e-bike’s riding position before investing in it. For short trips, the riding position might not make much difference, but for long journeys, the upright "Dutch" style with pulled-back handlebars is very comfortable – particularly for tall riders. The same goes for mountain bike styles, though these bikes are not often designed to actually go off-road.
The Shift S1 isn’t going to blow anyone away with amazing performance, but it is peppy enough to have a lot of fun on. And if you mostly travel by rideshares like Uber or scootershares like Bird, you can probably pay for the S1 after just a few months of cutting out app-based transportation. It’s hard to ask for too much more from such an inexpensive e-bike.
The Shift S1 isn’t going to blow anyone away with amazing performance, but it is peppy enough to have a lot of fun on. And if you mostly travel by rideshares like Uber or scootershares like Bird, you can probably pay for the S1 after just a few months of cutting out app-based transportation. It’s hard to ask for too much more from such an inexpensive e-bike.
If you’ve got the cash and want to get into ebikes, don’t buy this Rattan. My best advice if you have the money is buy a bike store bike with a Bosch/Brose/Yamaha/Shimano drivetrain. We review lots of them here but I’m currently riding a $2000 Raleigh. If you only have around $1,000+ to spend, head to Luna/Rad/Sondors or at least something from a company you’ve heard of with a Bafang motor.
While falling gas prices have temporarily halted years of gains in the number of bicycle commuters, more and more of us are using the bicycle to get around. It’s economical, provides good exercise, and is much cheaper than owning a car. But unless you’re in really good shape, you aren’t going to get very far. Enter the electric bike: a glorious new contraption allows us to get around without having to worry about arriving at our destinations a sweaty mess.

The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
But the good times of the stealthy ebike existence will not endure forever. The ebike market is growing steadily and more so, technology is driving performance up and costs down. The market for a green, lifestyle friendly, transportation technology, with GPS, theft ID, cell service and probably skim lattes is alive and driving an emerging market. It is a matter of time before we all must face and respond to the legal demands of the state and local laws. Not to be over obligatory about being legal and duty oriented, but I do call on my fellow ebikers to ride legal, whether ebike, moped or other. Go ahead and build the 1200W ebike of your dreams, but get it insured and licensed if you must. Such compliance will set the precedence for public acceptance of ebikes in general, and build a track record for expansion and mainstreaming of moped-speed ebikes for commuter value driven needs of the future.

Saddles also vary with rider preference, from the cushioned ones favored by short-distance riders to narrower saddles which allow more room for leg swings. Comfort depends on riding position. With comfort bikes and hybrids, cyclists sit high over the seat, their weight directed down onto the saddle, such that a wider and more cushioned saddle is preferable. For racing bikes where the rider is bent over, weight is more evenly distributed between the handlebars and saddle, the hips are flexed, and a narrower and harder saddle is more efficient. Differing saddle designs exist for male and female cyclists, accommodating the genders' differing anatomies and sit bone width measurements, although bikes typically are sold with saddles most appropriate for men. Suspension seat posts and seat springs provide comfort by absorbing shock but can add to the overall weight of the bicycle.
Some of the Rad Wagon’s (small) flaws became apparent once I added more weight to the bike. The integrated rear rack can attach various panniers, platforms, or baskets to cary your cargo, but I was most concerned with hauling my two kiddos to school. Riding the bike with my three year old was a cinch; he held on to the bars in the caboose (available as an accessory add-on) and enjoyed the view. Adding my very tall, almost seven-year-old daughter, however, was a bit more complicated.
Bicycles can be categorized in many different ways: by function, by number of riders, by general construction, by gearing or by means of propulsion. The more common types include utility bicycles, mountain bicycles, racing bicycles, touring bicycles, hybrid bicycles, cruiser bicycles, and BMX bikes. Less common are tandems, low riders, tall bikes, fixed gear, folding models, amphibious bicycles, cargo bikes, recumbents and electric bicycles.
In the 1890s, electric bicycles were documented within various U.S. patents. For example, on 31 December 1895 Ogden Bolton Jr. was granted Template:US Patent for a battery-powered bicycle with “6-pole brush-and-commutator direct current (DC) hub motor mounted in the rear wheel.” There were no gears and the motor could draw up to 100 amperes (A) from a 10-V battery.[3]
By 1898 a rear-wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel, was patented by Mathew J. Steffens. Also, the 1899 U.S. Patent 627,066 by John Schnepf depicted a rear-wheel friction “roller-wheel” style drive electric bicycle.[7] Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his U.S. Patent 3,431,994. Wood’s device used 4 fractional horsepower motors; connected through a series of gears.[8]
Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an e-bike dubbed Zike.[9] The bicycle included NiCd batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial e-bikes were available.
We'll start this off with the latest two Customer Profile videos. In the first one we follow up from the well received Leigh Cross video with a look at his son, Tig Cross. Tig's been refining an original bike concept combining the best parts of an ebike, scooter, and velomobile, and showcases the merits of an electric generator for the human drivertrain.

DIY Kit ebikes – Ebikes that are home built with a DIY kit, and exceed the 750W/20mph definition, are also allowed to be bought, build, and ridden. DIY kits are throttle activated. Some of the newer systems have PAS options. Ebike kits are not unilaterally prohibited or assigned motor vehicle status, but again, legal classification and road use falls under state law.
The Motan M-150 electric bike is one of the Addmotor’s best selling models. Featuring a 750W high-speed brushless rear hub motor, goes to the top speed of about 25mph. An upgraded 48V 11.6AH Panasonic lithium battery with improved reliability, makes going up a long, steep hills a breeze.  An upgraded 48V 11.6AH Panasonic battery provides improved reliability. This folding bike is designed to fit riders 5’4″-6’4″ and carry a max weight of 300 lbs, making it an ideal option even for larger riders. You can expect to get out 45-55 miles range while using the level one assist. Fully functional pedals also allow you to pedal without motor assist. Collapsible top-tube, frame, and pedals make it portable and easy to store in your car, and unfold in only 10 seconds when you’re ready to use it.
At just 36V and 5.2 Ah, the battery is not designed for long distance travel. GOTRAX claims the Shift S1 has a range of up to 15 miles (25 km), though that’s only with a lower pedal assist level. If you’re going full throttle, 10 miles (15 km) is a better estimate. But with a battery this small, you could easily charge it at your desk or in the corner of the classroom – lengthening your effective range.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
There are individuals who claim to have lost considerable amounts of weight by using an electric bike.[62] A recent prospective cohort study however found that people using e-bikes have a higher BMI.[63] By making the biking terrain less of an issue, people who wouldn't otherwise consider biking can use the electric assistance when needed and otherwise pedal as they are able.[64] This means people of lower fitness levels or who haven't cycled in many years can start enjoying the many health benefits E-bikes have to offer. [1]
Justin and Anne-Sophie have been on the road in Europe for about a week now, catching as much sun as they can on the Suntrip. Since the start of the trip in Lyon and the official start of the race in Chamonix, they have been trending on a more southerly route towards Turkey and Iran. As they get used to the style of travel and the nuances of riding a three-wheeled solar vehicle all day they have had their ups...
I got this bike last week. I loved it! This bicycle is a very good value, since it can be used in either manual or electric mode. Both the handlebar and seat height and inclination are adjustable. The assembly and use instructions are clear. In the manual mode the bike acts like any other six speed, there is a little red button that switches between manual and electric with each push. The electric mode is used either with the handlebar twist throttle or by peddling which activates it. The pedal brings the bike up to full speed while peddling slightly and with the throttle the speed is adjustable. I am very happy with my purchase.
State and Local Laws dictate your use, but cannot constitutionally supersede the federal law – Any ebike purchased within the 750W/20mph limits has no fear of being under federal motor vehicle classification, nor can any state classify them a motor vehicle. The ebike is considered a ‘bicycle’ for consumer purposes. However, the State Laws on local bike paths and local thruways may prohibit or limit ebike access. When bike path signs use word such as ‘motor vehicles’ and ‘motorbikes’ , the laws are likely referring to gas-ICE motorbikes/dirt bikes/scooters, and not ebikes. Other references to ‘motorized bicycles’ or ‘motorized vehicles’ sound more inclusive and probably are intended for either ebikes or gas mopeds. If in doubt, you always have the option to pedal unassisted by completely powering your bike down. Even though Federal law grant ebikes a bicycle status, the common consensus found in my research allows local and state law to add additional regulation to pathway and road access, just because “it has a motor”. So the Federal laws protects the consumer from the burden of motor vehicle requirements, but not the restrictions to local and state right of ways enjoyed by all non-motored bicycles.
Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an e-bike dubbed Zike.[9] The bicycle included NiCd batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial e-bikes were available.

Perhaps the cleverest thing of all about the Electric Brompton is that despite all the extra stuff, it folds up exactly the same as the non-powered variety. It's so simple, and unlike certain folding bikes we could mention, what you're left with is a genuinely small thing, rather than something that's about the size of a bike with the front wheel taken off.
×