China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008, and reaching an estimated fleet of 120 million e-bikes in early 2010. This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities. Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car. Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007. By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.
Riding position: You also may wish to check out an e-bike’s riding position before investing in it. For short trips, the riding position might not make much difference, but for long journeys, the upright "Dutch" style with pulled-back handlebars is very comfortable – particularly for tall riders. The same goes for mountain bike styles, though these bikes are not often designed to actually go off-road.
Bicycle suspensions are used primarily on mountain bicycles, but are also common on hybrid bicycles, as they can help deal with problematic vibration from poor surfaces. Suspension is especially important on recumbent bicycles, since while an upright bicycle rider can stand on the pedals to achieve some of the benefits of suspension, a recumbent rider cannot.
Depending on local laws, many e-bikes (e.g., pedelecs) are legally classified as bicycles rather than mopeds or motorcycles. This exempts them from the more stringent laws regarding the certification and operation of more powerful two-wheelers which are often classed as electric motorcycles. E-bikes can also be defined separately and treated under distinct Electric bicycle laws.
The Super Commuter is very aptly named. The 350w Bosch motor will help you sustain speeds of up to 28mph, and the burly, 2.4-inch wide, Schwalbe Super Moto-X 650b tires will keep you secure on even the roughest city streets, and Shimano Deore hydraulic brakes provide ample stopping power. Fenders provide welcome protection from road spray so you arrive at your destination fresh, integrated lights are critical for post-sunset riding, and a side-view mirror hanging on the left side of the handlebar gives a great view of traffic around you. After all, you can ride at the speed of urban traffic on the Super Commuter.
Because I am in an area with quite a lot of hills and steep inclines, some very steep, and the motor on the bike handles these hills effortlessly along with pedal assist. I will say I am not fit in anyway and there is no way I would have got up half of the hills I got up if it were not for the 250 watt motor on this bike, the low , medium and high pedal assist options are great and it is easy to assess which option you'll need depending on the hill.The battery was a lot heavier than I expected when holding it, feels like holiding a 3 LTR bottle of coca cola but I can forgive that
"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,  written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
The Dew-E packs functionality and fun into a rather traditional and conservative package. Front and rear fenders, integrated Busch & Müller front and rear lights, and a built-in Abus wheel lock make this a very practical commuter bike. An 11-34, 9-speed cassette and 1.75-inch tires provide versatility: You’ll ride smooth over rough city streets and zip down gravel bike paths with confidence. Front and rear rack mounts also give you the chance to outfit this bike for carrying more cargo or supplies for a longer day on the bike.
E-bikes use rechargeable batteries, electric motors and some form of control. Battery systems in use include sealed lead-acid (SLA), nickel-cadmium (NiCad), nickel-metal hydride (NiMH) or lithium-ion polymer (Li-ion). Batteries vary according to the voltage, total charge capacity (amp hours), weight, the number of charging cycles before performance degrades, and ability to handle over-voltage charging conditions. The energy costs of operating e-bikes are small, but there can be considerable battery replacement costs. The lifespan of a battery pack varies depending on the type of usage. Shallow discharge/recharge cycles will help extend the overall battery life.
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
A new European product safety standard EN 15194 will be published in 2009. EN 15194 contains several new requirements for ebikes to be sold in European Union and European Economic Area, including weight and voltage limitations. EN 15194 also defines a specific name for EU approved electrically-assisted cycles, EPAC - "Electrically Pedal Assisted Cycle".
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.
I do not recommend hacking a bike into s-pedelec, i.e. make a 25km/h bike go at 45 or faster. If you have an accident you will be in trouble. Just get a legal version. In addition you will have good insurance. Of course, in countries like France or the UK that so far do not know S-Pedelecs, you will have to make a difficult moral choice.... At least, make sure that your rig is safe...
Federal law in the United States states that an electric bicycle must have a top speed under 20 mph and a motor which produces less than 750 watts/1 hp. They are not considered motor vehicles by the federal government and are subject to the same consumer safety laws as unassisted bicycles. Their legality on public roads is under state jurisdiction, and varies. See the main Electric bicycle laws article for details on the law in individual states.
Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.
At 42 pounds for a size medium frame (exceptionally light for an urban e-bike), this step-through model’s silent, mid-drive Bosch Active Line motor provides pedal assist up to 20 mph. And its 400Wh battery lasts a claimed 30 to a whopping 110 miles, depending on mode, speed, terrain, rider weight, cargo—all the usual stuff. With 26-inch wheels, 2-inch tires, round aluminum tubes, a swept-back handlebar, Shimano Sora 9-speed components, and an 11-32 cassette, the Parkway looks like an everyday, non-motorized city bike at first glance. But with an array of Bosch e-components—motor, battery, and Purion display—it has the zip to take you farther faster.
An electric bike (also called e-bike, power-assist bike, pedelec…) is a fairly conventional bike combined with a battery and motor that helps out when you are pedaling to make it easier to get uphill or completely takes over driving and allows you to cruise along. Top quality electric bikes, along with electric scooters, are revolutionizing the bicycle industry. Not only is riding an e-bike simple and easy, but a rider can significantly extend their range with minimal cost or effort.
Most European bike rules are tight and restrictive. Right now the California state ebike rules in AB 1096 provide the clearest and cleanest format, and they support ebike riding. No other U.S. regulations come close. The big brand ebikes (Giant, Specialized, Trek) are selling bikes that fit within European rules (250w-300w motors). This gives them economies of scale.
It arrived safely, well packaged. It also shipped really quickly too. If you want to have an ebike for rides, this bike will work. it really helps to get over a couple steep hills. With pedal assist or the throttle it is like riding on a flat surface when it comes to inclines. The bike seems well constructed. The disc brakes work great, and the wheels and tires are very sturdy. For the price I think it was a very good deal.
Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.
Pedelecs are much like conventional bicycles in use and function — the electric motor only provides assistance, for example, when the rider is climbing or struggling against a headwind. Pedelecs are therefore especially useful for people in hilly areas where riding a bike would prove too strenuous for many to consider taking up cycling as a daily means of transport. They are also useful for riders who more generally need some assistance, e.g. for people with heart, leg muscle or knee joint issues.
Visually, the Pedego City Commuter Classic Electric Bike is stunning – a smart blend of yesteryear's style and today's technology. Pleasantly high handlebars, a sprung seat, and lovely Schwalbe Fat Frank tires make it very comfortable. Stopping is taken care of by powerful disk brakes, front and rear. Lights are included, as is a useful cargo rack. From an e-bike standpoint, the Pedego Classic City Commuter sports a reliable, hub-mounted motor driven by a 36-volt, 10-amp battery. There's a digital display with a trip computer, odometer, speedometer, pedal assist level, and battery charge information.
This Class 3 (28 mph), utilitarian, road e-bike is smooth and torquey thanks to its Bosch Performance Speed motor. With a drop bar and traditional road-bike position and handling, the CrossRip+ is more suited to longer rides on mixed terrain than navigating congested city streets. It comes with a rear rack—for mounting bags, not for attaching cargo directly—full fenders, a kickstand, and integrated front and rear lights (which are powered by a Bosch 500Wh battery). It features a SRAM Force 1x11 drivetrain, hydraulic disc brakes, and wide 700x38mm tires.
E-bikes use rechargeable batteries and the lighter ones can travel up to 25 to 32 km/h (16 to 20 mph), depending on local laws, while the more high-powered varieties can often do in excess of 45 km/h (28 mph). In some markets, such as Germany as of 2013, they are gaining in popularity and taking some market share away from conventional bicycles, while in others, such as China as of 2010, they are replacing fossil fuel-powered mopeds and small motorcycles.
An e-bike is identified as a "motor assisted cycle" (MAC) in British Columbia, which differs from electric mopeds and scooters, which are "limited-speed motorcycles." Motor assisted cycles must: have an electric motor of no more than 500 W; have fully operable pedals; not be capable of propelling the device at a speed greater than 32 km/hr [19.9 mph]. The engine must disengage when (a) the operator stops pedaling, (b) an accelerator controller is released, OR (c) a brake is applied. A driver's license, vehicle registration, and insurance are all not required. A bike helmet must be worn.
From the beginning and still today, bicycles have been and are employed for many uses. In a utilitarian way, bicycles are used for transportation, bicycle commuting, and utility cycling. It can be used as a 'work horse', used by mail carriers, paramedics, police, messengers, and general delivery services. Military uses of bicycles include communications, reconnaissance, troop movement, supply of provisions, and patrol. See also: bicycle infantry.
Available products (motors, senors, batteries, control systems. etc.) change fast since the e-bike market shows a strong growth. In principle, get a rear motor if you want a lot of raw power and acceleration (e.g. for a 500W motor). Middle motors are more energy efficient and less subject to problems (e.g. overheating). Middle motors usually are combined with integrated rear hub gears, and rear motors with derailleurs. Both have advantages and disadvantages. E.g. the former require less maintenance, are easy to use in go-and-stop traffic, but require taking off weight on pedals when shifting. Therefore the latter (derailleurs) are better for speedy overland and hills cycling.
For people wanting to push the effects of Statorade to the max, the Australian made Hubsinks can clamp on to your motor shell and provide additional cooling fins to shed heat to ambient air. These fit our new MXUS Cassette motors, and the 9C, Crystalyte H, and many others. These are listed on our new store category for motor cooling mods. And like other small products, we try to keep a stock of 10mL Statorade syringes on Amazon for easy shipping to US customers. They are sold out now but another shipment is inbound.
Haibike ships the HardNine with 29-inch tires, 180-millimeter hydraulic disc brakes, a 100-millimeter front suspension fork, and a nine-speed Shimano shifting system. The bike’s LCD readout is affixed to the handlebars and displays the current speed, level of charge, remaining range, and current pedal assist mode. The company says the battery can be completely recharged in just four hours, minimizing downtime between rides.
The electric bike revolution has officially crossed into the arena of off-road motorbikes. For those who prefer riding in nature, Cake introduced a product which not only respects the environment but other riders, as well. Cake’s Kalk is a silent off-road motorbike that releases no emissions into the atmosphere. Additionally, its electric motor means no gear changing or clutching — a silent motorbike that won’t detract from the experience of others. Perhaps the best part is Cake avoided any sacrifice in performance. The Kalk reaches speeds of fifty miles per hour and features three distinct driving modes: Discover, Explore, and Excite.
Alberta identifies e-bikes as "power bicycles" and is consistent with the federal definition of "power-assisted bicycle" in MVSR CRC, c 1038 s 2. Motor output must not exceed 500 W (0.671 hp) and e-bikes cannot travel faster than 32 km/h (20 mph). Fully operable pedals are required. No driver's license, vehicle insurance, or vehicle registration is required. Operators must be 12 years of age or older. All operators are required to wear a motorcycle helmet meeting the standards set in AR 122/2009 s 112(2). A passenger is permitted only if the e-bike is equipped with a seat designated for that passenger.
This dexterous electric dirt bike is recommended for anyone over the age of 14. It’s fitted with double suspension and big tyres to help you tackle tough terrain. You also get a good selection of gears, that gives you optimal control. The Razor can go as fast as 15 mph on average, and comes with an excellent braking system. The aesthetics are on point, and the racer look is sure to impress. Don’t forget your helmet!
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
As of 2008 a standard class C license, proof of insurance, and registration (annual fee: $9.00) are required for operation of any motorized pedalcycle in Pennsylvania. Additionally, there are strict equipment standards that must be met for operation, including: handlebars, brakes, tires/wheels, electrical systems/lighting, mirrors, speedometer, and horns/warning devices.
(15.5) "Electric assisted bicycle" means a device with two or three wheels which has a saddle and fully operative pedals for human propulsion and also has an electric motor. For such a device to be considered an electric assisted bicycle, it shall meet the requirements of the Federal Motor Vehicle Safety Standards, as set forth in 49 C.F.R. Section 571, et seq., and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied. The electric motor in an electric assisted bicycle shall:
At just 36V and 5.2 Ah, the battery is not designed for long distance travel. GOTRAX claims the Shift S1 has a range of up to 15 miles (25 km), though that’s only with a lower pedal assist level. If you’re going full throttle, 10 miles (15 km) is a better estimate. But with a battery this small, you could easily charge it at your desk or in the corner of the classroom – lengthening your effective range.
Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles, including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity. A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.
Hmm, I think it depends on the forest. My experience has been that if you have a Class 1 ebike and are riding respectfully, most places allow it. I have a sensitive knee and carry a doctor’s note citing disability laws in Colorado and have never been approached or asked by a ranger or fellow rider about the legality of my bike. That said, I have been using the really quiet and hidden Brose motor and I ride carefully and am friendly with everyone
About Terry Brightwater. Terry lives in the Afan Forest, South Wales, UK, with his wife Jay Brightwater. He is a professional Life Coach, specialising in “Emotional Fitness” for over 18 years. Terry’s passion for health and fitness, has spanned over the last 40 years, mainly being expressed through cycling, weight training and healthy eating. He … Continue reading eBikes as a Wonderful Health and Fitness Tool by Terry Brightwater
The "Dandy horse", also called Draisienne or Laufmaschine, was the first human means of transport to use only two wheels in tandem and was invented by the German Baron Karl von Drais. It is regarded as the modern bicycle's forerunner; Drais introduced it to the public in Mannheim in summer 1817 and in Paris in 1818. Its rider sat astride a wooden frame supported by two in-line wheels and pushed the vehicle along with his or her feet while steering the front wheel.
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers. If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.
OK, here we go. This electric scooter is also known as the DYU D1 over-seas, if you want to research it a little more, google that instead of Ancheer. This little thing is great. Once you put ten miles, or 16 kilometers on the odometer, the limiter turns off and this thing will hit in the ballpark of 20 mph! (I'm light so I've done 22 on a flat plane.) It has enough torque to go up hills, has functioning headlights and a brake-light, there's two apps you can download on the app store that will allow you to lock, change the speed settings, and see a digital speedometer of the bike. Very impressive in my opinion, even the handlebars fold over to make it easier to carry. The bike does not feel cheap, that outer tubular frame you're seeing is real metal. I'm 6' tall and I
The Shift S1 isn’t going to blow anyone away with amazing performance, but it is peppy enough to have a lot of fun on. And if you mostly travel by rideshares like Uber or scootershares like Bird, you can probably pay for the S1 after just a few months of cutting out app-based transportation. It’s hard to ask for too much more from such an inexpensive e-bike.
On a trip to Palo Alto last year, we had the chance to ride Specialized’s pedal-assisted Turbo Vado and the model is still our favorite ebike on the market. Utilizing a 350-watt motor and 604-watt-hour lithium-ion battery, the Turbo Vado is capable of traveling a whopping 80 miles on a single charge, which should be more than enough for any daily commute with plenty of miles left over.
If you need an ebike that can provide a full-on mountain bike experience, but you are also on a limited budget, this bike is an excellent choice for you. We doubt you can find a double suspension bike, jam-packed with features for a better price. Large wheels and low-rise handlebars provide more control and easier ride, but the powerful 500W brushless motor attached directly to the rear wheel hub will give you plenty of “umph”.
Massachusetts General Laws define three classes of motorized two-wheeled vehicles: Motorcycle, Motorized bicycle, and Motorized scooter. Although the definition of motorized scooter includes two-wheeled vehicles propelled by electric motors with or without human power, motorized scooter specifically excludes anything which falls under the definitions of motorized bicycle and motorcycle. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. Motorcycle includes any bicycle with a motor or driving wheel attached, with the exception of vehicles that fall under the specific definition of motorized bicycle. Thus, a pedal bicycle with an electric motor or a non-pedal bicycle with an electric motor, automatic transmission, and maximum speed of 30 miles an hour would fall under the definition of motorized bicycle. An electric bicycle that did not meet those restrictions would be either a motorized scooter or motorcycle, depending on specific characteristics.
We need to support and put our purchasing power behind ebikes sold in the U.S. that are trying to comply with the California rules which allow 500w and 750w nominal motors and establish 3 classes. If these bikes can create a big enough footprint in the market then future U.S. bike rules may universally adopt these standards. It is better than engaging in regulation showdowns without any standardized and unified proposal on the part of the Electric Bike Community.
An electric bicycle is a bicycle with an electric motor used to power the vehicle, or to assist with pedaling. In many parts of the world, electric bicycles are classified as bicycles rather than motor vehicles, so they are not subject to the same laws as motor vehicles. Electric bicycles are one type of motorized bicycle. However, electric bicycles are defined separately and treated as a specific vehicle type in many areas of legal jurisdiction.
Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.
Bicycles helped create, or enhance, new kinds of businesses, such as bicycle messengers, traveling seamstresses, riding academies, and racing rinks. Their board tracks were later adapted to early motorcycle and automobile racing. There were a variety of new inventions, such as spoke tighteners, and specialized lights, socks and shoes, and even cameras, such as the Eastman Company's Poco. Probably the best known and most widely used of these inventions, adopted well beyond cycling, is Charles Bennett's Bike Web, which came to be called the jock strap.
Brock had been running his esoteric shop on Cambie St. for over 30 years, pioneering the sale and production of recumbent bikes, tricycles, velomobiles, unicycles, and of course electric bicycles well before any of these things were popular. He was dabbling with early ebike conversions in the 1990's when we were still in grade school and has been for many years one of the few shops always willing to say yes to electric retrofits. We hope to still see him riding around streets of Vancouver in a white velomobile.
^ Consumer Product Safety Act, Pub. L. 107–319, December 4, 2002; codified at 15 U.S.C. 2085(b): The CPSC regulations do not differentiate between commercially manufactured low speed electric bicycles and those converted from ordinary bicycles by their owners using an aftermarket electric motor and battery kit, nor do they regulate the construction of electric-power bicycles using owner-built or sourced components.
Before you start shopping around for a new e-bike, the first thing you should ask yourself is, “how do I plan on using an electric bicycle?” How far do you plan on traveling? What type of terrain will you be traveling on? How much assistance do you need? Do you plan on pedaling – or do you want the bike to do all the work? Is this bike for daily commuting or casual riding? How fast do you need to go?
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.