Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3-wheeled bicycle that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Canadian Motor Vehicle Safety Standards (CMVSS) for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1–5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for each. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities.
The great majority of modern bicycles have a frame with upright seating that looks much like the first chain-driven bike. These upright bicycles almost always feature the diamond frame, a truss consisting of two triangles: the front triangle and the rear triangle. The front triangle consists of the head tube, top tube, down tube, and seat tube. The head tube contains the headset, the set of bearings that allows the fork to turn smoothly for steering and balance. The top tube connects the head tube to the seat tube at the top, and the down tube connects the head tube to the bottom bracket. The rear triangle consists of the seat tube and paired chain stays and seat stays. The chain stays run parallel to the chain, connecting the bottom bracket to the rear dropout, where the axle for the rear wheel is held. The seat stays connect the top of the seat tube (at or near the same point as the top tube) to the rear fork ends.
I would advocate you ride legal within the laws of your state. I would also look into some kind of liability rider or umbrella policy with your home owner’s policy, which covers your personal liability and theft. Get your bike registered; wear your helmet, eye protection, whatever is required by state law so that if an accident occurs and you are at fault, there is no legal recourse. Even if you own a 750W/20mph ebike that meets the definition of a bicycle, any at-fault cyclist may still be denied coverage by stingy insurance companies who want to support their clients. Your health insurance will usually cover your medical bills, but the costs of an expensive ebike may be lost.
The last 8 months we've been wrapping up some long duration testing of Statorade across different hub motor lines and performing experiments confirming its long term stability. These results have us pumped to introduce this motor cooling solution beyond DIY'ers and into wider markets. As an example, have a look at the video we below showing the effect this has on a small direct drive folding bike motor.
If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
^ Consumer Product Safety Act, Pub. L. 107–319, December 4, 2002; codified at 15 U.S.C. 2085(b): The CPSC regulations do not differentiate between commercially manufactured low speed electric bicycles and those converted from ordinary bicycles by their owners using an aftermarket electric motor and battery kit, nor do they regulate the construction of electric-power bicycles using owner-built or sourced components.
Electric bikes are considered motorcycles in Hong Kong, and therefore need type approval from the Transport Department, just as automobiles. All electric bikes available in Hong Kong fail to meet the type approval requirement, and the Transport Department has never granted any type approval for an electric bike, making all electric bikes effectively illegal in Hong Kong. Even if they got type approval, the driver would need a motorcycle driving license to ride. As a side note, Hong Kong doesn't have a moped vehicle class (and therefore no moped driving license), and mopeds are considered motorcycles too.
Having spent some quality time with Wing’s e-bike, I understand why so many people are excited about the growing popularity of electric-powered vehicles like bikes and scooters. They take a lot of the work out of getting from point A to point B, while retaining all of the joy. They can give you more confidence when navigating a treacherous city terrain that prioritizes cars over people. And let’s face it: bikes are cool, and always will be.
The word bicycle first appeared in English print in The Daily News in 1868, to describe "Bysicles and trysicles" on the "Champs Elysées and Bois de Boulogne". The word was first used in 1847 in a French publication to describe an unidentified two-wheeled vehicle, possibly a carriage. The design of the bicycle was an advance on the velocipede, although the words were used with some degree of overlap for a time.
The Riese & Müller Load Touring HS is billed as “the ultimate minivan of e-bikes,” and it holds up to that claim. With a low center of gravity (aided by the 20-inch front and 26-inch rear wheels), the Load is easy to handle. Tektro hydraulic disc brakes add control, and front and rear suspension provide comfort. The Bosch motor offers an assist up to 275 percent of your effort until you hit 28 mph, when it cuts out. Two 500Wh batteries give you 12 hours or more of range at full power. It’s capable of toting up to 220 pounds of pets, people, and less-animate cargo. R&M also sells a double child seat for kids up to age 6 and a child-seat fastener for your youngest passengers.
After you decide which style of e-bike you want, consider the class. In the U.S., there are three classes defined by the type of assist and how fast the motor will propel you. Most electric bikes sold are class 1 or 3. Class 1 bikes have a motor (max 750w) that assists while you’re pedaling, up to 20 mph. Class 3, also known as “speed pedelec,” can also have up to a 750w motor, but it can assist you up to 28 mph. Both are allowed in most states and cities without requiring a license. Class 2 models have throttles that don’t require the rider to pedal in order to get a boost. They’re allowed on most streets, bike lanes, and paths, but are less popular than the other classes and not covered much here (because not only do we still love to pedal, we also prefer the greater distances that pedal-assist bikes can cover).
Electric trikes have also been produced that conform to the e-bike legislation. These have the benefit of additional low speed stability and are often favored by people with disabilities. Cargo carrying tricycles are also gaining acceptance, with a small but growing number of couriers using them for package deliveries in city centres. Latest designs of these trikes resemble a cross-between a pedal cycle and a small van.
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2  as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
This Class 3 (28 mph), utilitarian, road e-bike is smooth and torquey thanks to its Bosch Performance Speed motor. With a drop bar and traditional road-bike position and handling, the CrossRip+ is more suited to longer rides on mixed terrain than navigating congested city streets. It comes with a rear rack—for mounting bags, not for attaching cargo directly—full fenders, a kickstand, and integrated front and rear lights (which are powered by a Bosch 500Wh battery). It features a SRAM Force 1x11 drivetrain, hydraulic disc brakes, and wide 700x38mm tires.
Electric bikes are here in a big way. Liberated from some of the normal constraints of standard bike design like weight and gearing, e-bike design has exploded; if you can imagine it, someone has built it. From cargo bikes to city bikes, messenger bikes to mountain bikes, road bikes, folding bikes, and even beach cruisers, there is something for everyone. The beauty of e-bikes is that they make the joy of cycling accessible to so many people in so many ways.
As of 2008 a standard class C license, proof of insurance, and registration (annual fee: $9.00) are required for operation of any motorized pedalcycle in Pennsylvania. Additionally, there are strict equipment standards that must be met for operation, including: handlebars, brakes, tires/wheels, electrical systems/lighting, mirrors, speedometer, and horns/warning devices.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
Massachusetts General Laws define three classes of motorized two-wheeled vehicles: Motorcycle, Motorized bicycle, and Motorized scooter. Although the definition of motorized scooter includes two-wheeled vehicles propelled by electric motors with or without human power, motorized scooter specifically excludes anything which falls under the definitions of motorized bicycle and motorcycle. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. Motorcycle includes any bicycle with a motor or driving wheel attached, with the exception of vehicles that fall under the specific definition of motorized bicycle. Thus, a pedal bicycle with an electric motor or a non-pedal bicycle with an electric motor, automatic transmission, and maximum speed of 30 miles an hour would fall under the definition of motorized bicycle. An electric bicycle that did not meet those restrictions would be either a motorized scooter or motorcycle, depending on specific characteristics.
We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).
One of the most important categories of ebikes is the low-cost, entry-level sector. What I call the eBigBox models. Obviously, not everyone can’t afford a $7500 Riese and Muller and frankly a lot of people are skeptical on how much they will use and enjoy an ebike. So even if they can afford a few thousand dollars for an ebike, they might not want to put it all down on a category they aren’t sure about.
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.
Both the Stromer and the Stoeckli are very nice looking designs and easy to handle. Reliability for both does not seem to be up to Swiss standards, e.g. some of the 2012 Stöcklis seem to have bad contacts. However, as of 2013, most of these problems should be fixed. The Cube got criticized for its battery/saddle system, but this has probably been fixed in more recent edition and it has less "punch" then the other's since the motor is smaller (324W?). I don't know about the BH Neo Nitro. Given the relatively low price of the BH Nitro, it may be the best buy in this category if you plan to cover smaller distances (the battery is limited to 9Ah, and Spain's industry does need some help ;) Anyhow, all of these models come with a variety of motors and country-specific modifications. E.g. in France, the BH Nitro comes with a 350W motor and is electronically limited to 25km/h, whereas in Switzerland you either can get a 500W - 45 km/h version or a 250W? - 25km/h version.
For those who missed seeing it live, we've also uploaded a youtube video of our live demonstration of a regular bike being converted over to electric assist. We hope that this helps demystify the process for some considering their first kit purchase. It was a fun opportunity as the owner of the bike was at the show and could ride it away the next day.
I did my commute a few times with the Rattan and while I would never give up my “bike store” e-bike for this, it was a worthy substitute. It never gave out on the big hills, nor did I have to brake because I felt the bike was falling apart. The frame is a little small for 6-foot me but it only comes in one size. I really miss the low rolling drag of having road tires however and this is something that both Rattan and Ancheer could improve upon. I don’t think many people are seriously off-roading with these bikes. Put some Schwalbe Big Bens on there!
Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).
It's a solid e-bike, but it's also very heavy one for a folding bike. I found it difficult carry when the bike is folded as the carrying handle is useless, and the center of gravity is towards to the rear wheel so one has to find a place in the rear of the bike to pick it up. Even when the bike is folded, it's bulky and heavy, It's difficult to walk with it while carrying it. It's easy to hurt one's back if he or she is not careful. I would not recommend carrying this bike up or down stairways.
But the good times of the stealthy ebike existence will not endure forever. The ebike market is growing steadily and more so, technology is driving performance up and costs down. The market for a green, lifestyle friendly, transportation technology, with GPS, theft ID, cell service and probably skim lattes is alive and driving an emerging market. It is a matter of time before we all must face and respond to the legal demands of the state and local laws. Not to be over obligatory about being legal and duty oriented, but I do call on my fellow ebikers to ride legal, whether ebike, moped or other. Go ahead and build the 1200W ebike of your dreams, but get it insured and licensed if you must. Such compliance will set the precedence for public acceptance of ebikes in general, and build a track record for expansion and mainstreaming of moped-speed ebikes for commuter value driven needs of the future.
At 42 pounds for a size medium frame (exceptionally light for an urban e-bike), this step-through model’s silent, mid-drive Bosch Active Line motor provides pedal assist up to 20 mph. And its 400Wh battery lasts a claimed 30 to a whopping 110 miles, depending on mode, speed, terrain, rider weight, cargo—all the usual stuff. With 26-inch wheels, 2-inch tires, round aluminum tubes, a swept-back handlebar, Shimano Sora 9-speed components, and an 11-32 cassette, the Parkway looks like an everyday, non-motorized city bike at first glance. But with an array of Bosch e-components—motor, battery, and Purion display—it has the zip to take you farther faster.
"Electric-assisted bicycle" means a bicycle with two or three wheels, a saddle, fully operative pedals for human propulsion, and an electric motor. The electric-assisted bicycle's electric motor must have a power output of no more than one thousand watts, be incapable of propelling the device at a speed of more than twenty miles per hour on level ground, and be incapable of further increasing the speed of the device when human power alone is used to propel the device beyond twenty miles per hour.
Electrically-assisted cycles are usually classified as either pedelecs or e-bikes. Under European Union regulations adopted in the UK in June 2003, only power-assisted cycles meeting the pedelec classification are considered to be pedal cycles. The maximum power allowed in the European Union for (pedelec) electric bicycles is 250 W, with a maximum assisted speed of 25 km/h.. To meet the pedelec specification the electric motor must be activated by the rider's pedalling effort and the power must cut out completely whenever the rider stops pedalling. Control of the motor by pedalling is often the key difference between a pedelec and e-bike.
Electric bikes vary widely in price, anywhere from $999 to $2000+, so you’ll have to determine how important certain features are to the overall cost. (However, we made a list of electric bikes under $1.000 here.)The battery used to power an electric bike motor is a key factor in how expensive a particular bike is. In general, the more miles a battery can provide, the more expensive it will be, so it’s important to consider the type of riding you plan on doing. If you know you’ll be using predominantly motor-generated power, then paying a bit more for a battery with a longer range is probably a good idea. Alongside with a good quality battery, motor is the most expensive part of an electric bike. Most standard electric bike motors come with a power rating of 250W, and the industry standard in the US is 500W. Maximum power of the motor you can legally use in the US is 750W. The non-electric components used on an electric bike are almost the same with those used on the conventional bicycles. The quality of the components used will affect the maintenance costs of your electric bike down the road, and more quality components mean higher upfront cost. Lastly, there is the frame. Since the frame is basically the skeleton of your electric bike, it’s wise to select a good material that will be the optimum combination of weight and durability.
Bicycles offer an important mode of transport in many developing countries. Until recently, bicycles have been a staple of everyday life throughout Asian countries. They are the most frequently used method of transport for commuting to work, school, shopping, and life in general. In Europe, bicycles are commonly used. They also offer a degree of exercise to keep individuals healthy.
By 1898 a rear wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel was patented by Mathew J. Steffens. Also, the 1899 Template:US Patent by John Schnepf depicted a rear wheel friction “roller-wheel” style drive electric bicycle. Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his Template:US Patent. Wood’s device used 4 fractional horsepower motors; each rated less than ½ horsepower and connected through a series of gears.
As long as the electric bicycle meets three criteria it is considered a low-speed electric bicycle, or simply a "bicycle." Three criteria: must travel less than 20 mph on flat ground without pedaling, must have functional pedals and must have less than a 750 watt motor. This is the same criteria as Federal Public Law 107-319. I checked my facts with the law office of Spohn, Spohn & Zeigler at 144 East Center Street, Marion, OH 43302 on August 21, 2009. A low-speed electric bicycle does not require registration, insurance, license plates (tags), or a driver's license. The rules of an electric bicycle are the same as a traditional bicycle. There is some confusion caused by Ohio interchanging the word Moped with "motorized bicycle." If a dealer sells you a bike that follows the guidelines of Federal Public Law 107-319, then you have a bicycle. If the bike has no pedals or has a higher wattage motor than 750 watts or can travel faster than 20mph you have a moped or scooter; Ohio requires tags and registration for mopeds and scooters.
This is a virtual hello to all the people who came by our booth last weekend at the BC Bike Show and are just now visiting our webpage for the first time. We had a great time and were delighted to see how much this event has grown recently. (And to those who lament that the bike show is now totally taken over by ebikes, well it's been over 15 years now that we've been trying to tell you all this day was coming!)
This article did a good job of trying to justify the assist speed limits but fell short of detailing how that can ever be effectively enforced. In reality the only enforcement that is going to work is applied speed limits to use of bikes and ebikes. For example, it makes sense that a bike lane on a street that the speed limit of vehicles is the speed limit of the bikes/ebikes. On sidewalks and shared pedestrian paths the speed limit probably does need to be in the 15-20mph range to match traditional bikes speeds on those paths.
But in Great Britain, the European Union definition is applicable, and the tighter restrictions of the Electrically Assisted Pedal Cycle Regulations 1983 (including a 200 kg weight limit on solo bicycles) were removed on 6 April 2015 by the Electrically Assisted Pedal Cycles (Amendment) Regulations 2015. Riders must be at least 14 years of age, but no driving licence is required.
Because e-bikes are capable of greater speeds for longer periods of time than standard bikes, you want extra control. Wider tires provide traction and some bump absorption with little penalty. You also want strong brakes to slow you (and all that extra weight) easily. It’s worth looking at the quality of the brakes and investing in bikes with better ones if you can.
Electric powered bicycles slower than 20 km/h without pedaling are legally recognized as a non-mechanically operated vehicle in China. According to "TECHNOLOGY WATCH", this should help promote its widespread use. Electric bicycles were banned in some areas of Beijing from August 2002 to January 2006 due to concerns over environmental, safety and city image issues. Beijing has re-allowed use of approved electric bicycles as of January 4, 2006. Some cities in China still ban electric bikes.
Most electric bicycles can be locked using keys supplied by the manufacturer. The key is usually inserted into a switch, which is commonly found on the bicycle's handlebars or on one side of the motor compartment. When switched to the "Off" position, the electrical drive system cannot be turned on. In areas of high risk for bicycle theft, these locking mechanisms are used in conjunction with coil or U locks.
Perhaps the cleverest thing of all about the Electric Brompton is that despite all the extra stuff, it folds up exactly the same as the non-powered variety. It's so simple, and unlike certain folding bikes we could mention, what you're left with is a genuinely small thing, rather than something that's about the size of a bike with the front wheel taken off.