In the 1890s, electric bicycles were documented within various U.S. patents. For example, on 31 December 1895, Ogden Bolton Jr. was granted U.S. Patent 552,271 for a battery-powered bicycle with "6-pole brush-and-commutator direct current (DC) hub motor mounted in the rear wheel". There were no gears and the motor could draw up to 100 amperes (A) from a 10-volt battery.
Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface." This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
GPS Firmware: This net update will be much appreciated by people who have a GPS Analogger device with their CA3. With a simple hardware modification to the Analogger circuit, the GPS data will be transmitted from your existing TRS cable back to the Cycle Analyst. You can then see the time of day, your elevation, position, and direction all on the CA3 screen. The firmware also features additional custom views on the main screen, allowing you to replace or toggle the battery voltage with any of these new parameters to get just the display you are after.
The oldest patent for an electric bike I've been able to find at the US Patent and Trademark Office is this one, by Ogden Bolton, Jr. of Canton Ohio, which was filed in September 1895 and granted three months later. You can see from these original diagrams that it bears an amazingly close resemblance to modern electric bikes. In the general picture on the left, you can see there's a hub motor on the rear wheel (blue), a battery suspended from the frame (red), and a simple handlebar control to make the thing stop and go. In the more detailed cutaway of the hub motor on the right, you can see there's a six-pole magnet in the center (orange) bolted to the frame and an armature (made from coiled wire, yellow) that rotates around it when the current is switched on. It's quite a hefty motor even by modern standards; Ogdon mentions "a heavy current at low voltage—for instance, to carry one hundred amperes at ten volts." So that's 1000 watts, which is about twice the power of a typical modern bike hub motor.
Further innovations increased comfort and ushered in a second bicycle craze, the 1890s Golden Age of Bicycles. In 1888, Scotsman John Boyd Dunlop introduced the first practical pneumatic tire, which soon became universal. Willie Hume demonstrated the supremacy of Dunlop's tyres in 1889, winning the tyre's first-ever races in Ireland and then England. Soon after, the rear freewheel was developed, enabling the rider to coast. This refinement led to the 1890s invention of coaster brakes. Dérailleur gears and hand-operated Bowden cable-pull brakes were also developed during these years, but were only slowly adopted by casual riders.
Even the humble bicycle hasn't escaped the clutches of modern technology. A whole herd of new e-bikes with electric motors are taking to our cities' streets. Adding a motor to a standard cycle does ramp up the price significantly, but it takes much of the effort out of cycling, making your commute to the office a sweat-free experience and allowing you to sit back and enjoy your suburban cruise.
This was the first ebike I ever bought. I've since become a builder and make my own. But this was a really reliable vehicle. I used it everyday for transportation. The company sent me any part I needed. It's got a power motor on it so it's super reliable. I wouldn't hesitate to buy this bike especially if you're new into the ebike world. If your looking to have some real fun buy this bike.. If your looking to meet new people buy this bike. If looking to go more green buy this bike. This bike is so much fun you well want to ride all day. This bike should be twice the price . I love love love it .
State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.
Saddles also vary with rider preference, from the cushioned ones favored by short-distance riders to narrower saddles which allow more room for leg swings. Comfort depends on riding position. With comfort bikes and hybrids, cyclists sit high over the seat, their weight directed down onto the saddle, such that a wider and more cushioned saddle is preferable. For racing bikes where the rider is bent over, weight is more evenly distributed between the handlebars and saddle, the hips are flexed, and a narrower and harder saddle is more efficient. Differing saddle designs exist for male and female cyclists, accommodating the genders' differing anatomies and sit bone width measurements, although bikes typically are sold with saddles most appropriate for men. Suspension seat posts and seat springs provide comfort by absorbing shock but can add to the overall weight of the bicycle.
In most jurisdictions, bicycles must have functioning front and rear lights when ridden after dark. As some generator or dynamo-driven lamps only operate while moving, rear reflectors are frequently also mandatory. Since a moving bicycle makes little noise, some countries insist that bicycles have a warning bell for use when approaching pedestrians, equestrians, and other cyclists, though sometimes a car horn can be used when a 12 volt battery is available.
As with all these bikes, the assisted speed is capped at 15mph, but unlike some of them, the Gtech eBike City or its identical (spec-wise) sibling the eBike Sport (this just has a standard frame rather than a step-through one) is light and agile enough for you to be able pedal harder without feeling like the weight is fighting you back down to 15mph. You can even, at a push, use it without the motor on flatter roads.
My one complaint is the bike’s weight. This sucker is heavy! The aluminum frame looks light, but the the hub motor (4 pounds) and battery (5 pounds) add up. The bike’s total weight is 39 pounds, which is about average for e-bikes but not something you’d want to lug around all day. “This is not a solution for everybody,” Miller admits. “If you live in a fifth floor walkup this is probably not going to work.”
I found that by sticking it on 'Turbo' or 'Sport' mode (the upper 2 of the 4 electrical assistance levels) and leaving it in a middle gear, the Centros felt zippy when in full flight, but able to pull away from the lights with no problems. Less lazy riders than me might want to actually use the 10 gears, and will find that in the top gear, it's quite easy to push past the mandated 15.5mph electrical limit.
The bicycle was recognized by 19th-century feminists and suffragists as a "freedom machine" for women. American Susan B. Anthony said in a New York World interview on February 2, 1896: "I think it has done more to emancipate woman than any one thing in the world. I rejoice every time I see a woman ride by on a wheel. It gives her a feeling of self-reliance and independence the moment she takes her seat; and away she goes, the picture of untrammelled womanhood.":859 In 1895 Frances Willard, the tightly laced president of the Woman’s Christian Temperance Union, wrote A Wheel Within a Wheel: How I Learned to Ride the Bicycle, with Some Reflections by the Way, a 75-page illustrated memoir praising "Gladys", her bicycle, for its "gladdening effect" on her health and political optimism. Willard used a cycling metaphor to urge other suffragists to action.
One of the profound economic implications of bicycle use is that it liberates the user from oil consumption.(Ballantine, 1972) The bicycle is an inexpensive, fast, healthy and environmentally friendly mode of transport. Ivan Illich stated that bicycle use extended the usable physical environment for people, while alternatives such as cars and motorways degraded and confined people's environment and mobility. Currently, two billion bicycles are in use around the world. Children, students, professionals, laborers, civil servants and seniors are pedaling around their communities. They all experience the freedom and the natural opportunity for exercise that the bicycle easily provides. Bicycle also has lowest carbon intensity of travel.
A "class 1 electric bicycle," or "low-speed pedal-assisted electric bicycle," is a bicycle equipped with a motor that provides assistance only when the rider is pedaling, and that ceases to provide assistance when the bicycle reaches the speed of 20 miles per hour. (2) A "class 2 electric bicycle," or "low-speed throttle-assisted electric bicycle," is a bicycle equipped with a motor that may be used exclusively to propel the bicycle, and that is not capable of providing assistance when the bicycle reaches the speed of 20 miles per hour. A "class 3 electric bicycle," or "speed pedal-assisted electric bicycle," is a bicycle equipped with a motor that provides assistance only when the rider is pedaling, (no throttle) and that ceases to provide assistance when the bicycle reaches the speed of 28 miles per hour, and equipped with a speedometer. Local government ordinances are allowed to permit or ban any class of electric bicycles on dedicated bicycle paths and trails, with Class 1 & 2 permitted, and Class 3 banned, by default.
An electric bike (also called e-bike, power-assist bike, pedelec…) is a fairly conventional bike combined with a battery and motor that helps out when you are pedaling to make it easier to get uphill or completely takes over driving and allows you to cruise along. Top quality electric bikes, along with electric scooters, are revolutionizing the bicycle industry. Not only is riding an e-bike simple and easy, but a rider can significantly extend their range with minimal cost or effort.
Vehicles exceeding any of the criteria above must be registered and titled as a motorcycle. Other types of vehicles, such as electric scooters, "pocket rockets" and mini-choppers, may fit the definition of a moped or a motorcycle, but cannot be registered by the Department of State if they lack the equipment required by law to legally drive on public roads.
Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.
I called Geico earlier today. They could insure me with Renters Insurance, but … I would need to have a Renter's Policy first, before the secondary insurance company they deal would insure my two bikes (Surly Long Haul Trucker and Yuba Sweet Curry custom eBike). BUT … unfortunately …. The company that would insure my bicycles will NOT insure me because we have a Pitbull !!! Can you believe that … !!!
Having spent some quality time with Wing’s e-bike, I understand why so many people are excited about the growing popularity of electric-powered vehicles like bikes and scooters. They take a lot of the work out of getting from point A to point B, while retaining all of the joy. They can give you more confidence when navigating a treacherous city terrain that prioritizes cars over people. And let’s face it: bikes are cool, and always will be.
Your local state may have very definite rules as to what is an e-bike, what is a moped, and what is a motorcycle. While ebikes enthusiast don’t want the motor vehicle label, it is certain that each state will define some power level and speed where that classification will apply. Your best source of information is to go directly to your state motor vehicle department website, and get a copy of the your local state vehicle codes, with NO EDITING. Only recently updated official state vehicle codes will contain all the latest changes to the laws.1 For a link to your state MVA, look here:2 http://eco-wheelz.com/electric-bike-laws.php
Motor-driven cycles may be operated on the roadway without registration, but the operator must have a driver's license. The cycle may not be operated on any sidewalk, limited access highway or turnpike. If the maximum speed of the cycle is less than the speed limit of the road, the cycle must operate in the right hand lane available for traffic or upon a usable shoulder on the right side of the road unless the operator is making a left turn.
Controllers for brushed motors: Brushed motors are also used in e-bikes but are becoming less common due to their intrinsic lower efficiency. Controllers for brushed motors however are much simpler and cheaper due to the fact they don't require hall sensor feedback and are typically designed to be open-loop controllers. Some controllers can handle multiple voltages.
I'm one of the hardcore cyclists at Ars, along with Jay Timmer and his new-as-of-last-fall road bike as well as copyeditor Kerry Staurseth. I love cycling, and it was a major factor in my dropping 120lb over a 12-month period starting in the summer of 2009. My daily rider/errand-runner is a 1998 Gary Fisher Marlin mountain bike. For longer rides, I use my 2009 Trek XO2 cyclecross bike. I've made a few modifications to it, including removing the bumpy cyclecross tires and swapping out the front 46-tooth chainring for a 50-tooth one. I went with a cross bike over a road bike because I'm still a Clydesdale, and I like the slightly longer wheelbase of a cross bike. I've also briefly owned a 2011 Trek Madone 5.9, which I sold not long after I bought it due to severely screwing up my right knee.
To legally operate a motorized bicycle or electric-assisted bicycle the operator must be licensed, the motorized bicycle/electric-assisted bicycle must be registered in one of the following definitions and meet the required safety equipment. If the operator or the motorized bicycle/electric- assisted bicycle does not meet all requirements, they will not be legal for street/highway use (including the sidewalk).To qualify as a motorized bicycle under state law they need to have motor of a piston displacement capacity of 50 cubic centimeters or less, maximum of two brake horsepower, maximum speed of not more than Template:Convert on a flat surface, fully operable pedals for human propulsion are not required, but may be a part of the machine.
One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.
An affordable GPS enabled bike security alarm device with text and email updates, runs on the 2G Verizon network to send notifications about location and status, includes iPhone, Android and web apps to control the device, track, and download ride data. Mounts to any standard bottle cage bosses if there is enough horizontal room, the device is 10" long and 3/4" thick with rubberized contacts to reduce vibration, rear rack and quick clamp mounting accessories available to work with just about any bike...
Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.
Rear-Mounted Hub Motor, installed on the rear wheel, are more common on pre-built bikes because they’re easily installed at the factory. For a conversion, it’s a little harder to install than a front hub motor because of the chain, gearing and derailleur. Plus, you may be limited to a 6 or 7-speed freewheel. However, rear wheel drive will provide more torque and is less noticeable than a front hub.
However, Emu sells a little foldable number if that's your bag. The Emu Crossbar is for town commuters that require a sweet ride that's backed up by solid Shimano Nexus hub gears and Tektro brakes, which are adequate if not the best on the market. Riding is smooth and easy, with the crank moving sensor doing its best to iron out any gaps in power delivery.