In Norway, e-bikes are classified as ordinary bicycles, according to the Vehicle Regulation (kjøretøyforskriften) § 4-1, 5g. Hence, e-bikes are not registered in the Vehicle Registry, and there is no demand for a license to drive them. Still, there are constraints on the bicycle construction. The maximum nominal motor power output can be no more than 250 watts and the maximum performance speed of the vehicle when the engine is running is 25 km per hour (15 mph). A function that reduces motor power when vehicle speed exceeds 25 km per hour is mandatory. However, if the motor is not running, the e-bike, or any other bike, answer only to the constraints of the ordinary speed limits.
Today, China is the world's leading producer of electric bicycles. According to the data of the China Bicycle Association, a government-chartered industry group, in 2004 China's manufacturers sold 7.5 million electric bicycles nationwide, which was almost twice the year 2003 sales; domestic sales reached 10 million in 2005, and 16 to 18 million in 2006. By 2007, electric bicycles were thought to make up 10 to 20 percent of all two-wheeled vehicles on the streets of many major cities. A typical unit requires 8 hours to charge the battery, which provides the range of 25–30 miles (40–50 km), at the speed of around 20 km/h.
I found that by sticking it on 'Turbo' or 'Sport' mode (the upper 2 of the 4 electrical assistance levels) and leaving it in a middle gear, the Centros felt zippy when in full flight, but able to pull away from the lights with no problems. Less lazy riders than me might want to actually use the 10 gears, and will find that in the top gear, it's quite easy to push past the mandated 15.5mph electrical limit.
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
Alberta identifies e-bikes as "power bicycles" and is consistent with the federal definition of "power-assisted bicycle" in MVSR CRC, c 1038 s 2. Motor output must not exceed 500 W (0.671 hp) and e-bikes cannot travel faster than 32 km/h (20 mph). Fully operable pedals are required. No driver's license, vehicle insurance, or vehicle registration is required. Operators must be 12 years of age or older. All operators are required to wear a motorcycle helmet meeting the standards set in AR 122/2009 s 112(2). A passenger is permitted only if the e-bike is equipped with a seat designated for that passenger.
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
In my research about ebikes and the law, I cannot begin to justify how often articles about the laws evolved into the various ways and techniques to sneak around public notice and be stealth with the your ebike. The goal is to ride fast and fun, stay away from public awareness, and ‘Fly under the Radar’. I have been there and I get the drift. Sales and production are up. Electric bike kits, DIY enthusiast, long distance commuters, and a general drive for value is raising the desire for more options for consumers, wanting speed for fun and function, while developing amnesia for the law. People want to ride their new ebikes, and have the same access to safe pathways as they did the week before on their 100% human bike. Rather than deal with the inevitable conflicts over access, behavior and perception within the general public, the typical user will try to blend in with the normal cycling community.
Some prohibitions also apply, such as on: carrying cargo that prevents keeping at least one hand on the handlebars or prevents proper use of brakes, riding no more than two abreast on a roadway or shoulder, and attaching the bicycle to another vehicle. Minn. Stat. § 169.222, subds. 3-5. The vehicles may be operated on a sidewalk except in a business district or when prohibited by a local unit of government, and must yield to pedestrians on the sidewalk. Minn. Stat. § 169.223, subd. 3. By default, electric-assisted bicycles are allowed on road shoulders as well as on bicycle trails, bicycle paths, and bicycle lanes.
About Terry Brightwater. Terry lives in the Afan Forest, South Wales, UK, with his wife Jay Brightwater. He is a professional Life Coach, specialising in “Emotional Fitness” for over 18 years. Terry’s passion for health and fitness, has spanned over the last 40 years, mainly being expressed through cycling, weight training and healthy eating. He … Continue reading eBikes as a Wonderful Health and Fitness Tool by Terry Brightwater
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.
EU: EN15194 (EPAC – Electrically Power Assisted Cycles) defines the use pedal-assisted less than 25k/h bikes: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.”
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers. Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.
In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris. The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind). It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.
It's a solid e-bike, but it's also very heavy one for a folding bike. I found it difficult carry when the bike is folded as the carrying handle is useless, and the center of gravity is towards to the rear wheel so one has to find a place in the rear of the bike to pick it up. Even when the bike is folded, it's bulky and heavy, It's difficult to walk with it while carrying it. It's easy to hurt one's back if he or she is not careful. I would not recommend carrying this bike up or down stairways.
An electric bicycle is a bicycle with an electric motor used to power the vehicle, or to assist with pedaling. In many parts of the world, electric bicycles are classified as bicycles rather than motor vehicles, so they are not subject to the same laws as motor vehicles. Electric bicycles are one type of motorized bicycle. However, electric bicycles are defined separately and treated as a specific vehicle type in many areas of legal jurisdiction.
Bicycle manufacturing proved to be a training ground for other industries and led to the development of advanced metalworking techniques, both for the frames themselves and for special components such as ball bearings, washers, and sprockets. These techniques later enabled skilled metalworkers and mechanics to develop the components used in early automobiles and aircraft.
Pedego’s Nationwide “Sole Source Provider” Program Expedites Bidding FOUNTAIN VALLEY, Calif., March 27, 2019 — Pedego® Electric Bikes, the nation’s Number 1 electric bike brand, presents the Pedego Patroller Edition, a high-performance electric mountain bike designed to empower law enforcement, security and safety personnel as they protect and serve. Pedego
This is a cool eBike fits in your car's trunk or back seat! It's well made. And it only has one rear disc brake, you dont really need the front brake. It's simple to operate and fun to use - just put one foot on one foot attachment while turning the throttle slightly, then as soon as you start to move add the other foot...and let the joy ride begin!
What an experience. I really had no idea what to expect when I first got on. The ride was smooth, and the assisting function was excellent and seamless. It is not like a motorcycle, it is just like a bike with some extra help. I felt completely safe on this bike, as well as comfortable in the seat. Especially in San Francisco with all the hills, going up the ramp felt like I was moving on a flat surface still. For commuters who might be worried about having to change clothes during an arduous commute in on their bike, fear not. This bike makes everything easy, and simple enough that you could ride to work in your work clothes and not fear getting too hot and sweaty. For those who have switched to the bike to decrease their impact on the environment, this bike is a must. Get there fast,
Bicycles helped create, or enhance, new kinds of businesses, such as bicycle messengers, traveling seamstresses, riding academies, and racing rinks. Their board tracks were later adapted to early motorcycle and automobile racing. There were a variety of new inventions, such as spoke tighteners, and specialized lights, socks and shoes, and even cameras, such as the Eastman Company's Poco. Probably the best known and most widely used of these inventions, adopted well beyond cycling, is Charles Bennett's Bike Web, which came to be called the jock strap.
Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.
Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3-wheeled bicycle that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Canadian Motor Vehicle Safety Standards (CMVSS) for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1–5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for each. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities.
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
If you’ve got the cash and want to get into ebikes, don’t buy this Rattan. My best advice if you have the money is buy a bike store bike with a Bosch/Brose/Yamaha/Shimano drivetrain. We review lots of them here but I’m currently riding a $2000 Raleigh. If you only have around $1,000+ to spend, head to Luna/Rad/Sondors or at least something from a company you’ve heard of with a Bafang motor.
The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations. The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.