The great majority of modern bicycles have a frame with upright seating that looks much like the first chain-driven bike. These upright bicycles almost always feature the diamond frame, a truss consisting of two triangles: the front triangle and the rear triangle. The front triangle consists of the head tube, top tube, down tube, and seat tube. The head tube contains the headset, the set of bearings that allows the fork to turn smoothly for steering and balance. The top tube connects the head tube to the seat tube at the top, and the down tube connects the head tube to the bottom bracket. The rear triangle consists of the seat tube and paired chain stays and seat stays. The chain stays run parallel to the chain, connecting the bottom bracket to the rear dropout, where the axle for the rear wheel is held. The seat stays connect the top of the seat tube (at or near the same point as the top tube) to the rear fork ends.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885. However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
Both the Stromer and the Stoeckli are very nice looking designs and easy to handle. Reliability for both does not seem to be up to Swiss standards, e.g. some of the 2012 Stöcklis seem to have bad contacts. However, as of 2013, most of these problems should be fixed. The Cube got criticized for its battery/saddle system, but this has probably been fixed in more recent edition and it has less "punch" then the other's since the motor is smaller (324W?). I don't know about the BH Neo Nitro. Given the relatively low price of the BH Nitro, it may be the best buy in this category if you plan to cover smaller distances (the battery is limited to 9Ah, and Spain's industry does need some help ;) Anyhow, all of these models come with a variety of motors and country-specific modifications. E.g. in France, the BH Nitro comes with a 350W motor and is electronically limited to 25km/h, whereas in Switzerland you either can get a 500W - 45 km/h version or a 250W? - 25km/h version.
I got this bike last week. I loved it! This bicycle is a very good value, since it can be used in either manual or electric mode. Both the handlebar and seat height and inclination are adjustable. The assembly and use instructions are clear. In the manual mode the bike acts like any other six speed, there is a little red button that switches between manual and electric with each push. The electric mode is used either with the handlebar twist throttle or by peddling which activates it. The pedal brings the bike up to full speed while peddling slightly and with the throttle the speed is adjustable. I am very happy with my purchase.
Some US companies, notably in the tech sector, are developing both innovative cycle designs and cycle-friendliness in the workplace. Foursquare, whose CEO Dennis Crowley "pedaled to pitch meetings ... [when he] was raising money from venture capitalists" on a two-wheeler, chose a new location for its New York headquarters "based on where biking would be easy". Parking in the office was also integral to HQ planning. Mitchell Moss, who runs the Rudin Center for Transportation Policy & Management at New York University, said in 2012: "Biking has become the mode of choice for the educated high tech worker".
Speaking of which, if you're used to non-electric cycles, be aware that e-bikes are heavy and capped at 25kph or 15.5mph. In many cases, that means the bike starts to feel like its actively fighting against you, if you try to push the speed higher than that by pedalling. That's especially true with heavier bikes, for obvious reasons, and can take a while to get used to.
E-bikes are classified in three different types: Class 1 and Class 3 bikes are powered proportionally to the “input” a rider gives via pedaling. “It feels natural, and you’re still riding a bike, so all your reflexes, skill and comfort you’ve developed over years of riding bikes apply immediately,” says Fritz Rice, sales manager of Gregg’s Cycles, near Greenlake.
While we're still fairly new to the solar ebike game, Mark is among the (suprisingly numerous) Grin customers who've been thinking about and experimenting with solar bikes for many years. After he shared pictures of his latest project and mentioned his round the world touring ambitions, we thought we had to do a small feature on this guy. A quick last minute trip to Maker Faire was arranged to meet up, and here we present, Mark Havran:
There are two basic categories of electric bike, and their uses don't offer equal crossover value. The first category is essentially a normal bicycle that has been outfitted with an electric motor. These bikes are the same size as a standard bicycle, and handle almost identically, save for the obvious benefit of added motive power thanks to a motor and battery.
Would an e-bike that used a trailing generator to power the electric motor still be considered an e-bike? The purpose of the generator is allow greater distances to be traveled and all day riding. The gen-set that I am looking at uses a 49 cc gas engine with a 12 volt generator, this would be from the ground up build using a 1 hp electric motor. This seems to stay within the state laws of AZ. where I reside. Thanks for your thoughts.
We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).