That aside, the Axis is a fantastic e-bike. At 'only' 16kg, it's almost lively by e-bike standards, but it also feels rock solid. It's geared too low in my opinion – I think it's fair to say I am not the target market – but in 8th, you can breeze on past the legally mandated, electrically-assisted 15.5mph. The hydraulic disk brakes will then bring you to a pleasingly rapid dead stop. The range and charging time are good, too. Cheap it is not, mind you.
I do not recommend hacking a bike into s-pedelec, i.e. make a 25km/h bike go at 45 or faster. If you have an accident you will be in trouble. Just get a legal version. In addition you will have good insurance. Of course, in countries like France or the UK that so far do not know S-Pedelecs, you will have to make a difficult moral choice.... At least, make sure that your rig is safe...
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.
Thanks for your excellent article. I’ve been riding ebike for about 16 years. My first electric bike was a Meridian pedal assist bike. I just up graded to a new bike. I’m 73, so I wanted a pedal assist bike that had a throttle. I researched for several months and bought what I think is the best bike for the money. It’s a Rad Rover 2017 fat bike. It has a 750 watt mother with a 48 volt 11.6 amp battery. It’s a fantastic bike, that is a lot of fun to ride. You might want to check it out and add it to your list of bikes. Rad Rover also make a city commuter bike, a cargo bike and a folding bike. You can’t beat their price for a quality bike. Thanks again for both of your articles. They were very informative.
The list below should be complete with both a literature analysis and by mining course materials. In principle, everything that can be research also can be education. Therefore we also listed a few items found in the literature. There are some interesting issues that refer to organizational and informal learning, i.e. users participating in design and policy making.
I would add that the point of the article seems to encourage ebikers to “know the state laws” and be confident within those boundaries. To D McCarthy’s question, if your state has a definition for ebikes and classifies them as bicycles and affords access as bicycles, AND, your particular ebike is built within those specifications, then you should be able to ride that section of road with confidence. Just my 2C.
Our hope is that this plug will become to motors in the 500-1500 watt power range what the 9pin Z910 became for the low power geared motors, with all motor manufacturers agreeing to the same pinout standard for easy swapping and interchangeability . We have an L10 version of the Phaserunner motor controller available now and will soon be expanding this to a Grinfineon offering as well.
"Electric-assisted bicycle" means a bicycle with two or three wheels, a saddle, fully operative pedals for human propulsion, and an electric motor. The electric-assisted bicycle's electric motor must have a power output of no more than one thousand watts, be incapable of propelling the device at a speed of more than twenty miles per hour on level ground, and be incapable of further increasing the speed of the device when human power alone is used to propel the device beyond twenty miles per hour.[66]
Another big upgrade here is the 36V battery. Instead of the 8Ah that the Ancheer had, Rattan has a 10.4Ah battery. The battery actually looks a lot like this one that goes for $190 on ebay or a little more on Amazon. Rattan tells me it is full of genuine LG cells which seem to perform quite well. On cold days, my 15 km (10 mile) very hilly commute would use up about half of the battery (Ancheer would be dying on the way back home). I imagine someone significantly under my 200+lbs could approach the 25 miles Rattan says you can get on throttle alone or up to 50 miles of pedal assist. I’ll just say it was significantly more than the Ancheer.

Most consumers want an e-bike that will accommodate its motor without being too cumbersome and will remain stable in spite of its electronic components. Some consumers want only the most basic of e-bike features, including lights, a cargo rack/basket, and a water bottle holder. Others are focused more heavily on safety features, such as brake type. And still others are concerned with convenience and portability.
The E-bike is everything it was advertised to be. It's big and fast and fun to ride especially when riding uphill with pedal assist you have the superhuman ability to get up those tuff climbs that would normally leave you winded and probably walking the bike. The setup was fairly simple however the frame had a couple of serious deep scratch marks in the otherwise impeccable paint job. And even though it's purely cosmetic it was still very disappointing to receive a brand new bike in this condition. It's not clear to me what if anything I can do about it but I still love the bike.
To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.
Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).
The E-bike is everything it was advertised to be. It's big and fast and fun to ride especially when riding uphill with pedal assist you have the superhuman ability to get up those tuff climbs that would normally leave you winded and probably walking the bike. The setup was fairly simple however the frame had a couple of serious deep scratch marks in the otherwise impeccable paint job. And even though it's purely cosmetic it was still very disappointing to receive a brand new bike in this condition. It's not clear to me what if anything I can do about it but I still love the bike.
The Ohio Revised Code 4511.01 [121] distinguishes motorized bicycles and mopeds from motorcycles or scooters by describing them as "...any vehicle having either two tandem wheels or one wheel in the front and two wheels in the rear, that is capable of being pedaled and is equipped with a helper motor of not more than fifty cubic centimeters piston displacement that produces no more than one brake horsepower and is capable of propelling the vehicle at a speed of no greater than twenty miles per hour on a level surface." One brake horsepower converts to 0.75 kW, or (rounded) 750W. Thus, a bicycle with an electric helper motor operating under 750W, and not propelling the bicycle over 20 mph, does not qualify to be registered under Ohio state law. Local jurisdictions may have other regulations.
Solar Shunt firmware: With this firmware the Cycle Analyst can use the auxilliary input as a second current sensor for measuring and showing the solar amps and watts. You can not only see in realtime how much solar power is coming into the pack, you also get combined statistics such as the %solar recharge and the net wh/km mileage taking into account the solar input for the day. This is the ideal instrument for looking at solar ebike performance, consolodating all measurements in a single device.
My homeowners (State Farm) covers bikes , but assumes $500 per bike. They will add the bikes as personal property, but the premium is excessive (about $300/year per bike, and we have four bikes). I did increase our personal umbrella liability coverage, and it covers us if family members any sort of accident on our e-bikes that injures us or others or others' property, though only covers $500 each for our own bikes (under the homeowners coverage). It was not very expensive to increase the umbrella policy (as it resulted also in a reduced rate on our car insurance).
The Tidalforce Electric Bicycle was an electric bicycle manufactured by Wavecrest Labs from 2003 until the company went out of business in 2006. All models of Wavecrest Tidalforce electric bikes have a 36 volt electric hub motor built into the rear wheel hub and a 36 volt battery pack built into the front wheel hub. Wavecrest Labs manufactured three models of Tidalforce bikes: The Wavecrest Tidalforce M-750, the S-750 Traditional hard tail mountain bike and the iO-750 Cruiser. Any of the three bikes with an X suffix denotes that the motor is a 1000 watt motor without a set speed restriction as compared to the speed limited 750 watt version.
While falling gas prices have temporarily halted years of gains in the number of bicycle commuters, more and more of us are using the bicycle to get around. It’s economical, provides good exercise, and is much cheaper than owning a car. But unless you’re in really good shape, you aren’t going to get very far. Enter the electric bike: a glorious new contraption allows us to get around without having to worry about arriving at our destinations a sweaty mess.
There are specialized bicycle tools for use both in the shop and on the road. Many cyclists carry tool kits. These may include a tire patch kit (which, in turn, may contain any combination of a hand pump or CO2 Pump, tire levers, spare tubes, self-adhesive patches, or tube-patching material, an adhesive, a piece of sandpaper or a metal grater (for roughing the tube surface to be patched), Special, thin wrenches are often required for maintaining various screw fastened parts, specifically, the frequently lubricated ball-bearing "cones".[57][58] and sometimes even a block of French chalk.), wrenches, hex keys, screwdrivers, and a chain tool. There are also cycling specific multi-tools that combine many of these implements into a single compact device. More specialized bicycle components may require more complex tools, including proprietary tools specific for a given manufacturer.
Unrelated to the show but also of local interest. The BC government is soliciting input on what is meant by "active transportation" which could hopefully help to direct policy and regulation governing not just ebikes but all kinds of human scaled transport. If you think electric skateboards should be on their radar or faster S-Pedalec class ebikes then this is a chance to have your voice heard. Electric bicycles have been an entirely grass roots phenomenon for most of their trajectory and it's encouraging to see the entire scope of personal mobility finally being acknowledged and discussed at this level.
Put the wheel with the electric hub on your bike and connect the brake components. Simply reverse the process you used to remove the wheel in order to reinstall it. Be sure to adjust the chain so it fits properly if you’re replacing the back wheel. If the bike has rim or cantilever brakes, simply close them over the new wheel using the lever. If the bike has disc brakes, put the pads back in place and secure them using the clips, springs, or cotter or retaining pin.[11]
Range is a key consideration with e-bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider.[36][37] Some manufacturers, such as the Canadian BionX or American Vintage Electric Bikes,[38] have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[39] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS. E-bikes developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains.[40] The bicycles were then charged from the mains, as is common today. While ebike batteries were produced mainly by bigger companies in past, many small to medium companies have started using innovative new methods for creating more durable batteries. State of the art, custom built automated precision CNC spot welding machines[41] created 18650 battery packs[42] are commonly used among Do-it-yourself ebike makers.
For many ebike owners, doing their ebike thing usually becomes more than a hobby and good exercise on the weekend with the riding club. It becomes a lifestyle, a utility machine, a darn fun piece of technology on two wheels. As the industry grows and becomes more popular, these unique bikes will be a daily part of many lives and mold into the framework of legal society.
Toe-clips and toestraps and clipless pedals help keep the foot locked in the proper pedal position and enable cyclists to pull and push the pedals. Technical accessories include cyclocomputers for measuring speed, distance, heart rate, GPS data etc. Other accessories include lights, reflectors, mirrors, racks, trailers, bags, water bottles and cages, and bell.[52] Bicycle lights, reflectors, and helmets are required by law in some geographic regions depending on the legal code. It is more common to see bicycles with bottle generators, dynamos, lights, fenders, racks and bells in Europe. Bicyclists also have specialized form fitting and high visibility clothing.
I'm wondering if renter's insurance will cover my eBike while I'm out cycling around town to work, shopping, or even on long distance eBike tours ….. And what exactly will the insurance cover … only the bicycle …. all of the extra features …. gadgets … gear ….. This beast will cost me around $9,500.00 (US) when finished. At times I will be carrying as much as $3,000.00+ worth of gear !!!
Motor-driven cycles may be operated on the roadway without registration, but the operator must have a driver's license.[85] The cycle may not be operated on any sidewalk, limited access highway or turnpike. If the maximum speed of the cycle is less than the speed limit of the road, the cycle must operate in the right hand lane available for traffic or upon a usable shoulder on the right side of the road unless the operator is making a left turn.

Bicycle brakes may be rim brakes, in which friction pads are compressed against the wheel rims; hub brakes, where the mechanism is contained within the wheel hub, or disc brakes, where pads act on a rotor attached to the hub. Most road bicycles use rim brakes, but some use disk brakes.[49] Disc brakes are more common for mountain bikes, tandems and recumbent bicycles than on other types of bicycles, due to their increased power, coupled with an increased weight and complexity.[50]
Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.

Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.
Play it Safe, Make it Easy – E-bike manufacturers will offer you a large variety of styles, types, colors and utility, but the base specifications will be a bike producing less than 750 watts of power (1 horsepower = 746W) , and have its speed limited to 20mph on motor power alone. The majority of US ebikes meet that specification. Manufacturers do this for their own liability. Going this route assures you that your bike was built and sold legally. As a result, you will have about every privilege that a normal bicycle can expect. However, state and local laws may dictate reduced speeds and limited access to bike paths.
Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.[16]
We bought 2 of these to go along with our AW 26"x1.75" Front Wheel Electric Bicycle Motor Kits and they work perfectly! The batteries that came with and were recommended by the wheel manufacturer were "clunky", had to be mounted in hanging bags and just didn't work well. These Li-ion Battery with Battery Holders are sleek, fit our Beach Cruisers perfectly, give us a rack to carry our "beach stuff" and one of the best features is how easy they are to charge! They lock in place when we are out and about, but I can unlock them, slide them both out and take them into the RV for charging when we return. Very happy with these and would recommend to anyone looking to convert their current bike into e-bikes!

This thing is also kitted out with a full SRAM groupset, RockShox Yari RC front shocks, Custom Fox Float suspension at the rear and enormously punchy SRAM disc brakes at the front and rear. Fundamentally, it's a mighty off-road machine with pro-spec kit that introduces a new style of trail riding, allowing adrenaline junkies to ride further, climb harder and descend faster than ever before.
E-bikes can boost bike usage, offer health benefits and use “an order of magnitude less carbon dioxide than a car traveling the same distance,” according to a 2016 research review published in the journal Transport Reviews.  In fact, access to an e-bike increased cycling trips and distances traveled – and nearly doubled the bike as a mode of transportation, observed one Norwegian study.
An affordable GPS enabled bike security alarm device with text and email updates, runs on the 2G Verizon network to send notifications about location and status, includes iPhone, Android and web apps to control the device, track, and download ride data. Mounts to any standard bottle cage bosses if there is enough horizontal room, the device is 10" long and 3/4" thick with rubberized contacts to reduce vibration, rear rack and quick clamp mounting accessories available to work with just about any bike...

Bicycles and horse buggies were the two mainstays of private transportation just prior to the automobile, and the grading of smooth roads in the late 19th century was stimulated by the widespread advertising, production, and use of these devices.[9] More than 1 billion bicycles have been manufactured worldwide as of the early 21st century.[1][2][3] Bicycles are the most common vehicle of any kind in the world, and the most numerous model of any kind of vehicle, whether human-powered or motor vehicle, is the Chinese Flying Pigeon, with numbers exceeding 500 million.[1] The next most numerous vehicle, the Honda Super Cub motorcycle, has more than 60 million units made, while most produced car, the Toyota Corolla, has reached 35 million and counting.[4][5][6][32]


The first mechanically-propelled, two-wheeled vehicle may have been built by Kirkpatrick MacMillan, a Scottish blacksmith, in 1839, although the claim is often disputed.[20] He is also associated with the first recorded instance of a cycling traffic offense, when a Glasgow newspaper in 1842 reported an accident in which an anonymous "gentleman from Dumfries-shire... bestride a velocipede... of ingenious design" knocked over a little girl in Glasgow and was fined five shillings.[21]

"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Chapter 551., titled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D.[58] The following definition of electric bicycle was passed by the Texas legislature in 2001. "Electric bicycle" means a bicycle that is designed to be propelled by an electric motor, exclusively or in combination with the application of human power, cannot attain a speed of more than 20 miles per hour without the application of human power; and does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle[0] on a highway that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle[0] on a highway used primarily by pedestrians.
×