Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]

No endorsement is required on a driver license in order to operate a motorized bicycle, thus the motorized bicycle may be operated by anyone with a valid driver license. Goggles, windshields and other special equipment required for motorcycles and motor-driver cycles are not required for operation of a motorized bicycle. However, crash helmets are required regardless of operators age. Minors between the ages of 14 and 16 may apply for a restricted license to operate a motorized bicycle, just as they would to operate a motor-driver cycle. For instance, they must take a written test, vision tests and demonstrate their ability to operate the motorized bicycle. The license issued will be restricted to a motorized bicycle only. The license is valid only during daylight hours and within a seven-mile (11 km) radius of the driver's home. Applicants for any type of license less than eighteen (18) years old, must complete a Minor/Teen-age Affidavit and Cancellation form making the parent or legal guardian financially liable for the applicants action. [57]
Photo: Could solar power be the future of electric bicycles? The large solar panel mounted over the back wheel of this experimental bike powers an electric motor connected by a chain drive to the back wheel, helping the rider when he doesn't feel like pedaling. Using clean, green solar power would remove the problem of having to charge electric bikes with electricity generated from fossil fuels—and help to extend their range significantly. Photo by Warren Gretz courtesy of US DOE/NREL.
We bought 2 of these to go along with our AW 26"x1.75" Front Wheel Electric Bicycle Motor Kits and they work perfectly! The batteries that came with and were recommended by the wheel manufacturer were "clunky", had to be mounted in hanging bags and just didn't work well. These Li-ion Battery with Battery Holders are sleek, fit our Beach Cruisers perfectly, give us a rack to carry our "beach stuff" and one of the best features is how easy they are to charge! They lock in place when we are out and about, but I can unlock them, slide them both out and take them into the RV for charging when we return. Very happy with these and would recommend to anyone looking to convert their current bike into e-bikes!

European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.


Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3-wheeled bicycle that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Canadian Motor Vehicle Safety Standards (CMVSS) for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1–5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for each. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities.[31]
Even with cheaper or heavier bikes, once you accept that you are really meant to pedal gently and let the motor do the work, non-speed freaks will get into it. E-bikes are great for commuting and for places that aren't pancake flat. They'll pull you away from the lights quickly, iron out hills and stop you getting sweaty, so you can bin the Lycra and ride in jeans, a suit, or a winter coat.
Electric powered bicycles slower than 20 km/h without pedaling are legally recognized as a non-mechanically operated vehicle in China.[32] According to "TECHNOLOGY WATCH", this should help promote its widespread use.[33] Electric bicycles were banned in some areas of Beijing from August 2002 to January 2006 due to concerns over environmental, safety and city image issues. Beijing has re-allowed use of approved electric bicycles as of January 4, 2006.[34] Some cities in China still ban electric bikes.
Put the wheel with the electric hub on your bike and connect the brake components. Simply reverse the process you used to remove the wheel in order to reinstall it. Be sure to adjust the chain so it fits properly if you’re replacing the back wheel. If the bike has rim or cantilever brakes, simply close them over the new wheel using the lever. If the bike has disc brakes, put the pads back in place and secure them using the clips, springs, or cotter or retaining pin.[11]
The other is our first foray into the larger 45mm wide motor series, similar to those sold by MXUS, QS, Leafbike etc. as 3KW or 5kW hubs. We got these made up to properly fit either a standard 135mm dropout with a single speed freewheel, or a 150mm dropout with a 7-8 speed freewheel and some spacers. As expected from Grin they are sealed, include a 10K thermistor for temperature sensing, and have a disk hole injection port for Statorade, and are hubsink compatible. Check out the performance on our simulator both with and without statorade. Unlike so many other direct drive motors, both of these have the proper alignment for disk rotor position and room for disk calipers without shimming things out.
About Terry Brightwater. Terry lives in the Afan Forest, South Wales, UK, with his wife Jay Brightwater. He is a professional Life Coach, specialising in “Emotional Fitness” for over 18 years. Terry’s passion for health and fitness, has spanned over the last 40 years, mainly being expressed through cycling, weight training and healthy eating. He … Continue reading eBikes as a Wonderful Health and Fitness Tool by Terry Brightwater
Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).

On the other hand, the battery doesn’t lock into the bike, which means you can’t just leave it on your bike when you park at the bike rack. Anyone could walk by and simply remove your battery. That seems like an oversight to me, though perhaps the designers assumed that such a small battery would just be easy to take with you. And it is. My wife could probably lose this battery in her purse.
The word bicycle first appeared in English print in The Daily News in 1868, to describe "Bysicles and trysicles" on the "Champs Elysées and Bois de Boulogne".[11] The word was first used in 1847 in a French publication to describe an unidentified two-wheeled vehicle, possibly a carriage.[11] The design of the bicycle was an advance on the velocipede, although the words were used with some degree of overlap for a time.[11][12]
From all the Chinese brands that have come and disappeared, Onway is still standing strong. That means that they have sold enough bikes, and they have been tried and tested enough for customers to know what to expect. So, what can you expect from this Onway bike? Well, for a very affordable price, you will get anything you realistically need in an e-bike – multi-purpose tires for various terrains, LCD display, LED headlights, taillights, a kickstand… Overall build quality and quality of the parts is above average, but there are some things that you will need to change, and seat should be the first on the list. Customer support is not that great, but if you decide to purchase this bike you will get a fun bike, for affordable price that you will be able to assemble and ride in no time.
The frame itself incorporates a series of mounts allowing you to easily trick-out the Road E+1 with a rack, fenders, or panniers to more aptly meet your touring requirements. Again, most touring purists will certainly scoff at the mere notion of pedal-assistance, however, individuals looking for more of a guided tour and less of a tour de force will swoon over the Road E+1.
Bicycles and horse buggies were the two mainstays of private transportation just prior to the automobile, and the grading of smooth roads in the late 19th century was stimulated by the widespread advertising, production, and use of these devices.[9] More than 1 billion bicycles have been manufactured worldwide as of the early 21st century.[1][2][3] Bicycles are the most common vehicle of any kind in the world, and the most numerous model of any kind of vehicle, whether human-powered or motor vehicle, is the Chinese Flying Pigeon, with numbers exceeding 500 million.[1] The next most numerous vehicle, the Honda Super Cub motorcycle, has more than 60 million units made, while most produced car, the Toyota Corolla, has reached 35 million and counting.[4][5][6][32]
Maryland defines an "electric bicycle" as a vehicle that (1) is designed to be operated by human power with the assistance of an electric motor, (2) is equipped with fully operable pedals, (3) has two or three wheels, (4) has a motor with a rating of 500 watts or less, (5) and is capable of a maximum speed of 20 miles per hour on a level surface when powered by the motor. (Senate Bill 379, approved by the Governor 5/5/2014, Chapter 294.) [96] This legislation excludes "electric bicycle" from the definition of "moped", "motorized minibike", and "motor vehicle", and removes the titling and insurance requirements required for electric bicycles under prior Maryland law.

Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.[5]


Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.[16]
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.
Great question… a real world situation from someone doing their best to follow the law but also be realistic about time/distance. What follows is my opinion on the matter based on lots of electric bike riding experience, this is not legal advice. You can probably ride with electric assist across the dirt way with no issues and avoid any negative response that might arise as long as you’re polite to other cyclists and pedestrians and pedal along without going too fast. If someone called you out about it you could easily hop off, walk your bike and explain that you use the assist to help make your commute possible or possibly, like me, you have a knee injury and it’s difficult to pedal through softer terrain like gravel. Another different approach might be to shut the bike off completely before entering the gravel section, you could even take the battery off and put it in a backpack or as mentioned earlier… just walk the bike. Imagine if you had a motorized dirt bike and were just pushing it along a sidewalk… this kind of vehicle definitely is not allowed on sidewalks or most gravel paths like the one you’re describing but if you were escorting it carefully, you’d be honoring the spirit of the law and if an officer or pedestrian jumped out and started questioning you about your “motorized vehicle” it is my feeling that a genuine explanation and apology or request for guidance would go very well. I personally have never had issues riding electric bikes in part because I am thoughtful about how I use them. I do occasionally switch them off and sometimes I get off and walk. I have asked police in many cities across the US what they thought about ebikes and in every case I have received positive interest and support with guidance to ride safe with a helmet and follow traffic laws in the street. I hope this helps and I wish you well, it’s nice that you care enough to ask and I hope you’re treated well by others out on the road. The flip side of this response is that I have been harassed, yelled at and even swerved at by automobiles when riding bicycles and electric bikes. This usually happens in the evening after work lets out when traffic is heavy and I’m riding on the shoulder or in the street (where marked to do so) and I believe it has to do with territory, testosterone and socio-economic standing more so than laws or anything like that.
The release of Garmin’s new Edge 520 Plus GPS bike computer made a big splash in the world of cycling. It was an impressive upgrade, likely a response to increasing competition from the likes of Wahoo. But the Garmin Edge 520 Plus upgrade has caused a little confusion, because it seems to offer the same mapping and navigation capabilities as the more expensive Edge 820 and 1030. We clear up the confusion with two in-depth posts, Garmin Edge 520 vs 520 Plus, and Garmin Edge 1030 vs 820 vs 520 Plus.
The bicycle is also used for recreational purposes, such as bicycle touring, mountain biking, physical fitness, and play. Bicycle competition includes racing, BMX racing, track racing, criterium, roller racing, sportives and time trials. Major multi-stage professional events are the Giro d'Italia, the Tour de France, the Vuelta a España, the Tour de Pologne, and the Volta a Portugal.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885.[7][8][9] However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.[23][24][25]
The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.

Like most electric bikes, the Rad Wagon is also fairly heavy, weighing 72 pounds. The last drawback is that it comes in only one frame size (which I imagine helps to keep costs lower) that fits rider heights between 5 foot 2 inches and 6 foot 2 inches. My 6 foot 4 husband, however, can ride the bike just fine, so there’s some wiggle room to this range.
It’s a topic that many eMTBers are interested in: fast charging. What has long been a reality with electric cars is now also being partly improved for ebikes with high amperage chargers. Bosch has presented a 6A charger this year that can charge a 500 Wh battery in 3 hours, more than a third faster than the standard charger. The new benchmark next year, however, will probably be the 10A charger presented by Haibike and BMZ. It is claimed to be capable of charging a 630 Wh battery in just 1.5 hours.
According to Utah Code 41-6a-102 (17) an electric assisted bicycle is equipped with an electric motor with a power output of not more than 750 watts and is not capable of further assistance at a speed of more than 20 MPH, or at 28 MPH while pedaling and using a speedometer. New laws specifically exclude electric pedal-assisted bicycles as "motorized vehicles" and bicycles are permitted on all state land (but not necessarily on Indian Reservations, nor restrictive municipalities, such as in Park City Code 10-1-4.5 2) if the motor is not more than 750 Watts, and the assistance shuts off at 20 mph (Utah Traffic Code 53-3-202-17-a 1). E-bikes sold in Utah are required to have a sticker that details the performance capacity. Children under 14 can operate an electric bicycle if accompanied by a parent/guardian, but children under 8 may not. (Utah code 41-6a-1115.5) No license, registration, or insurance is required by the State but some municipalities may require these measures (Salt Lake City and Provo require registration).
In Israel, persons above 16 years old are allowed to use pedal-assisted bicycle with power of up to 250W and speed limit of 25 km/hour. The bicycle must satisfy the European Standard EN15194 and be approved by the Standards Institution of Israel. A new law, effective January 10, 2019, states that riders under 18 who have no automobile license will need a special permit. [51] [52] Otherwise, no license or insurance is required. Other motorized bicycles are considered to be motorcycles and should be licensed and insured as such.[53] The maximum weight of the e-bike itself cannot exceed 30 kg.[54]

IZIP ebikes is currently holding their huge annual sale. We know that IZIP makes high quality electric bikes that you can buy and ride with confidence. The current sale is a clearance of their 2018 models. One of the best ways to get a good deal on any bike is to buy a previous year’s model. Plus, IZIP offers free same-day shipping. So we have highlighted two of the best bargains in ebikes available from IZIP right now.
The bicycle's invention has had an enormous effect on society, both in terms of culture and of advancing modern industrial methods. Several components that eventually played a key role in the development of the automobile were initially invented for use in the bicycle, including ball bearings, pneumatic tires, chain-driven sprockets and tension-spoked wheels.[10]
If you want an e-bike that positively sprays tech out you, try the Volt Axis on for size. It takes the GoCycle GS's combo of folding, lightweight frame and disk brakes and adds automatic gears, if you please. These react to your speed and pedalling effort. So you automatically gear down when you stop at traffic lights – although what self-respecting cyclist does that? – and then back up as you accelerate.
At 42 pounds for a size medium frame (exceptionally light for an urban e-bike), this step-through model’s silent, mid-drive Bosch Active Line motor provides pedal assist up to 20 mph. And its 400Wh battery lasts a claimed 30 to a whopping 110 miles, depending on mode, speed, terrain, rider weight, cargo—all the usual stuff. With 26-inch wheels, 2-inch tires, round aluminum tubes, a swept-back handlebar, Shimano Sora 9-speed components, and an 11-32 cassette, the Parkway looks like an everyday, non-motorized city bike at first glance. But with an array of Bosch e-components—motor, battery, and Purion display—it has the zip to take you farther faster.

Maryland defines an "electric bicycle" as a vehicle that (1) is designed to be operated by human power with the assistance of an electric motor, (2) is equipped with fully operable pedals, (3) has two or three wheels, (4) has a motor with a rating of 500 watts or less, (5) and is capable of a maximum speed of 20 miles per hour on a level surface when powered by the motor. (Senate Bill 379, approved by the Governor 5/5/2014, Chapter 294.) [96] This legislation excludes "electric bicycle" from the definition of "moped", "motorized minibike", and "motor vehicle", and removes the titling and insurance requirements required for electric bicycles under prior Maryland law.
Bicycle shall mean (1) every device propelled solely by human power, upon which any person may ride, and having two tandem wheels either of which is more than fourteen inches in diameter or (2) a device with two or three wheels, fully operative pedals for propulsion by human power, and an electric motor with a capacity not exceeding seven hundred fifty watts which produces no more than one brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than twenty miles per hour on level ground.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
In a friction drive motor, a small, solid wheel rotates against the side of the tire in order to drive it. The first motorcycles used the same concept, with a motor mounted above the front wheel. The problem is that the drive rubs at the side of the tire. It's inefficient, and it quickly wears the sidewall away. Tires need to be replaced every couple hundred miles. For this reason, you'll seldom see electric bikes with this type of drive anymore.
Rear-Mounted Hub Motor, installed on the rear wheel, are more common on pre-built bikes because they’re easily installed at the factory. For a conversion, it’s a little harder to install than a front hub motor because of the chain, gearing and derailleur. Plus, you may be limited to a 6 or 7-speed freewheel. However, rear wheel drive will provide more torque and is less noticeable than a front hub.
I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.

The Registrar will permit an electric motor driven cycle to be registered if it meets Canada Motor Vehicle Safety Standards (CMVSS) as a Limited Speed Motorcycle, or Scooter as is done with gas powered motor driven cycles. If the vehicle was manufactured after 1988 it will bear a compliance label stating that it meets these standards. The operator will be subject to all the requirements placed on operators of motor driven cycles.
DON'T BUY THIS BIKE!!!!! Worst customer service ever!!! I bought this bike for my 18 year old son to commute to school. It worked well for the first 2 months but the battery is cheap and stated to wear out. I tried going on the website, but they battery shows as out of stock, and has been for 3 months now. I left 5 emails with customer service, never got a reply. Also there is no number listed on their website to even speak to a real person. Now I have a worthless 5 month old bike..... horrible this company should be ashamed.
Electric bikes aren’t just a practical and environmentally conscious solution to gridlock, they also are really fun to ride. On top of all of the persuasive arguments to get an electric bike, I think the Rad Wagon’s best-selling point comes down to enjoyment. Zooming down the street each morning I wasn’t angrily yelling at fellow drivers or rushing not to be late. The bike commute was part of the journey each day, and not just the means I used to get around. There’s a reason so many people loved biking as a kid, and it can be just as fun as an adult.
Even the humble bicycle hasn't escaped the clutches of modern technology. A whole herd of new e-bikes with electric motors are taking to our cities' streets. Adding a motor to a standard cycle does ramp up the price significantly, but it takes much of the effort out of cycling, making your commute to the office a sweat-free experience and allowing you to sit back and enjoy your suburban cruise.
This 150mm-travel e-mtb tackles big descents, shines on flowy trails, and provides the boost you need for the trip back. Pedal assist comes from Shimano’s 6.2-pound STePS E8000 motor with a 20mph boost. Shifting is motorized too, with Shimano’s exemplary XT Di2 drivetrain providing the most precise and consistent shifts a mountain bike can have. The fun comes from the E-Core’s 150mm of front and rear travel courtesy of a RockShox Yari fork and Deluxe RT shock. Both can be locked out for long, fire-road type climbs, though on an e-bike that feature feels less necessary.
The great majority of modern bicycles have a frame with upright seating that looks much like the first chain-driven bike.[7][8][9] These upright bicycles almost always feature the diamond frame, a truss consisting of two triangles: the front triangle and the rear triangle. The front triangle consists of the head tube, top tube, down tube, and seat tube. The head tube contains the headset, the set of bearings that allows the fork to turn smoothly for steering and balance. The top tube connects the head tube to the seat tube at the top, and the down tube connects the head tube to the bottom bracket. The rear triangle consists of the seat tube and paired chain stays and seat stays. The chain stays run parallel to the chain, connecting the bottom bracket to the rear dropout, where the axle for the rear wheel is held. The seat stays connect the top of the seat tube (at or near the same point as the top tube) to the rear fork ends.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
However, Emu sells a little foldable number if that's your bag. The Emu Crossbar is for  town commuters that require a sweet ride that's backed up by solid Shimano Nexus hub gears and Tektro brakes, which are adequate if not the best on the market. Riding is smooth and easy, with the crank moving sensor doing its best to iron out any gaps in power delivery. 
×