The environmental effects involved in recharging the batteries can of course be reduced. The small size of the battery pack on an e-bike, relative to the larger pack used in an electric car, makes them very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots", in which e-bike riders can charge their vehicles while parked under photovoltaic panels.[66]
A new European product safety standard EN 15194 will be published in 2009. EN 15194 contains several new requirements for ebikes to be sold in European Union and European Economic Area, including weight and voltage limitations. EN 15194 also defines a specific name for EU approved electrically-assisted cycles, EPAC - "Electrically Pedal Assisted Cycle".
eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …
Built by a company that’s made cycling equipment for more than four decades, the Vado feels more like a traditional bicycle than almost any other ebike. Its frame and components have been tuned to provide a familiar experience, making it easy for new and long-time cyclists to jump on and start pedaling. Specialized’s heritage shines through nicely, helping separate itself from the competition in an increasingly crowded ebike market.
E-bikes can also provide a source of exercise for individuals who have trouble exercising for an extended time (due to injury or excessive weight, for example) as the bike can allow the rider to take short breaks from pedaling and also provide confidence to the rider that they'll be able to complete the selected path without becoming too fatigued[58] or without having forced their knee joints too hard (people who need to use their knee joints without wearing them out unnecessarily may in some electric bikes adjust the level of motor assistance according to the terrain). A University of Tennessee study provides evidence that energy expenditure (EE) and oxygen consumption (VO2) for e-bikes are 24% lower than that for conventional bicycles, and 64% lower than for walking. Further, the study notes that the difference between e-bikes and bicycles are most pronounced on the uphill segments.[59] Reaching VO2 Max, can really help your body as a whole[60]. Professor Janet Lord of Birmingham University in the UK published a study that looked at older cyclists, ““The study looked at muscle mass, blood cholesterol, their VO2 Max, lung function, and in many of those measures we found they didn’t age! No loss of muscle, their bones were a little thin (but nothing like the general population), their blood pressure didn’t go up.[61]
The aluminum, step-through eJoy is the happy medium between traditional-looking townies that don’t transport much more than the rider and often cumbersome cargo models that are sometimes a challenge to store. With 26-inch wheels, full fenders, a Shimano Alivio nine-speed drivetrain and disc brakes, a wheelbase similar to the average townie, and a big, comfy seat, it has the appearance of a practical everyday cruiser. But its oversize rear rack, silent Bosch Active Line motor, heavy-duty head tube with front-tray mounts (the tray is an add-on), integrated Supernova E3 lights, and roll-over-anything balloon tires hurtle it into hmm-this-could-actually-replace-my-car status. It’s one of the quietest, most convenient, most stylish, and easiest-to-operate e-bikes available.
State and Local Laws dictate your use, but cannot constitutionally supersede the federal law – Any ebike purchased within the 750W/20mph limits has no fear of being under federal motor vehicle classification, nor can any state classify them a motor vehicle. The ebike is considered a ‘bicycle’ for consumer purposes. However, the State Laws on local bike paths and local thruways may prohibit or limit ebike access. When bike path signs use word such as ‘motor vehicles’ and ‘motorbikes’ , the laws are likely referring to gas-ICE motorbikes/dirt bikes/scooters, and not ebikes. Other references to ‘motorized bicycles’ or ‘motorized vehicles’ sound more inclusive and probably are intended for either ebikes or gas mopeds. If in doubt, you always have the option to pedal unassisted by completely powering your bike down. Even though Federal law grant ebikes a bicycle status, the common consensus found in my research allows local and state law to add additional regulation to pathway and road access, just because “it has a motor”. So the Federal laws protects the consumer from the burden of motor vehicle requirements, but not the restrictions to local and state right of ways enjoyed by all non-motored bicycles.
Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle's crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle's standard drive train.
Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[68]
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
For many bikes, battery range is more important than total power (because they’re all pretty powerful). You want a bike that delivers a range long enough for your rides at the power levels you want. Most e-bikes will have three to five levels of assist that kick in anywhere from 25 percent of your pedal power to 200 percent. Consider how fast the battery takes to recharge, especially if you’ll be using your bike for long commutes.
Rad Power’s lineup of 2019 bikes start at $1,699 (there’s also a Cyber Monday special on their 2018 models), proving that electric bikes don’t have to be over $2,000 to have the amenities and quality you need for daily commuting. Of course, that’s still a steep price for some. But as prices keep dropping in the e-bike industry, affordability breeds better access, and this might be the key that our cities—and their traffic—so desperately need.
Attitudes to electric bikes have changed in recent years. For a long time they were seen by cyclists as 'cheating' and by non-cyclists as being just like a bike, but uglier and far more expensive. This new breed of best-in-class electric bikes feel more natural, look more normal, and people are coming around to the idea that a ride with the convenience of a bike but without all the sweat and effort is a Very Good Thing. 
No person may drive either a two-wheeled or a three-wheeled motorcycle, or a motor-driven cycle unless such person has a valid driver's license specially endorsed by the director to enable the holder to drive such vehicles. No driver's license is required for operation of an electric-assisted bicycle if the operator is at least sixteen years of age. Persons under sixteen years of age may not operate an electric-assisted bicycle. Persons operating electric-assisted bicycles shall comply with all laws and regulations related to the use of bicycle helmets. Electric-assisted bicycles and motorized foot scooters may have access to highways of the state to the same extent as bicycles. Electric-assisted bicycles and motorized foot scooters may be operated on a multipurpose trail or bicycle lane, but local jurisdictions may restrict or otherwise limit the access of electric-assisted bicycles and motorized foot scooters, and state agencies may regulate the use of motorized foot scooters on facilities and properties under their jurisdiction and control.
The recommendation depends a lot on what you plan to use the bike for and how you plan to ride. That said, I would recommend at least a 750 (if not 1,000) watt motor, and, if you want reasonable range, 48 or 52v cells with a minimum rating of 19ah. For shorter rides, you can use a smaller battery. Multiply battery voltage by amp hour rating to get battery watt hours. Divide the watt hours by the motors power rating to get a general idea of how many hours of heavy use you might get. I’d also recommend a mid drive as opposed to a hub drive, or to find a hub drive wheel rated to take your and the bicycle's combined weight.

For many ebike owners, doing their ebike thing usually becomes more than a hobby and good exercise on the weekend with the riding club. It becomes a lifestyle, a utility machine, a darn fun piece of technology on two wheels. As the industry grows and becomes more popular, these unique bikes will be a daily part of many lives and mold into the framework of legal society.


To qualify as an electric-assisted bicycle under state law they need to have a seat and fully operable pedals for human propulsion, meet federal motor vehicle safety standards, an electric motor that has a power output of not more than 1,000 watts, maximum speed of not more than 20 mph (electric motor and human power combined), disengages or ceases to function when the vehicle’s brakes are applied, two or three wheels
Some electric bikes claim to use a neat trick called regenerative braking. If you start pedaling the bicycle or going downhill, the spinning wheels turn the electric motor in the hub in reverse and start charging up the batteries. In practice, regenerative braking is nowhere near as useful on an electric bicycle as it is on an electric train or car. An electric bike has much less mass and velocity than either a train or car, so it never gains (or loses) anything like as much kinetic energy when it starts and stops. You'd have to go down an awful lot of hills to charge up the batteries completely and that's usually not practical. And what's the point in pedaling the wheels simply to charge the battery? You might as well have bought an ordinary bicycle to start with!
Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.

Front-Mounted Hub Motor can be found on pre-built bikes or on custom conversions. Mounted to the front wheel, this is the easiest configuration to setup if you’re converting a standard bicycle since there’s no derailleur or chain to worry about. And since most e-bike conversions include batteries mounted to the rear rack, using a front hub motor helps equalize the weight of the bike and makes it easier to handle. But there’s a small risk the motor could cause the front forks to brake. That’s why it’s vital you only use a front hub motor on a steel fork. For pre-built bikes, this shouldn’t be an issue since the motors are usually lower-powered on steel forks.
The bicycle's invention has had an enormous effect on society, both in terms of culture and of advancing modern industrial methods. Several components that eventually played a key role in the development of the automobile were initially invented for use in the bicycle, including ball bearings, pneumatic tires, chain-driven sprockets and tension-spoked wheels.[10]
I would add that the point of the article seems to encourage ebikers to “know the state laws” and be confident within those boundaries. To D McCarthy’s question, if your state has a definition for ebikes and classifies them as bicycles and affords access as bicycles, AND, your particular ebike is built within those specifications, then you should be able to ride that section of road with confidence. Just my 2C.
It’s a topic that many eMTBers are interested in: fast charging. What has long been a reality with electric cars is now also being partly improved for ebikes with high amperage chargers. Bosch has presented a 6A charger this year that can charge a 500 Wh battery in 3 hours, more than a third faster than the standard charger. The new benchmark next year, however, will probably be the 10A charger presented by Haibike and BMZ. It is claimed to be capable of charging a 630 Wh battery in just 1.5 hours.

At $799, it is one of the most affordable full-size folding electric bicycles on the market. There are cheaper folding e-bikes out there, but they generally have much smaller wheels and lower top speeds. With 16″ wheels and a max speed of 32 km/h (20 mph), the Shift S1 combines the specs of higher priced e-bikes with the affordability of a budget folder.


In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.

Some of the Rad Wagon’s (small) flaws became apparent once I added more weight to the bike. The integrated rear rack can attach various panniers, platforms, or baskets to cary your cargo, but I was most concerned with hauling my two kiddos to school. Riding the bike with my three year old was a cinch; he held on to the bars in the caboose (available as an accessory add-on) and enjoyed the view. Adding my very tall, almost seven-year-old daughter, however, was a bit more complicated.
Flyer Vollblut. A new rear motor bike from one of the most reliable E-bike makers. This model doesn't look as "heavy" as most other Flyer models. The Vollblut 500 has the 500W new Panasonic rear motor, front fork suspension, 28 inch wheels. It is in the same price range as the Stöckli and the Stromer. Flyer is known for top service and reliability, but it's a new model with a new motor ....
A motorized bicycle shall not be operated by any person under sixteen years of age, nor at a speed in excess of twenty-five miles per hour, upon any public highway, private way laid out under authority of statute, way dedicated to public use, or way under the control of park commissioners or body having like powers, within the commonwealth.[99] A motorized bicycle shall not be operated on any way by any person not possessing a valid driver's license or learner's permit. Every person operating a motorized bicycle upon a way shall have the right to use all public ways in the commonwealth except limited access or express state highways where signs specifically prohibiting bicycles have been posted, and shall be subject to the traffic laws and regulations of the commonwealth and the regulations contained in this section, except that the motorized bicycle operator may keep to the right when passing a motor vehicle which is moving in the travel lane of the way, and the motorized bicycle operator shall signal by either hand his intention to stop or turn. Motorized bicycles may be operated on bicycle lanes adjacent to the various ways, but shall be excluded from off-street recreational bicycle paths. Every person operating a motorized bicycle or riding as a passenger on a motorized bicycle shall wear protective headgear conforming with such minimum standards of construction and performance as the registrar may prescribe, and no person operating a motorized bicycle shall permit any other person to ride a passenger on such motorized bicycle unless such passenger is wearing such protective headgear.
In cities where bicycles are not integrated into the public transportation system, commuters often use bicycles as elements of a mixed-mode commute, where the bike is used to travel to and from train stations or other forms of rapid transit. Some students who commute several miles drive a car from home to a campus parking lot, then ride a bicycle to class. Folding bicycles are useful in these scenarios, as they are less cumbersome when carried aboard. Los Angeles removed a small amount of seating on some trains to make more room for bicycles and wheel chairs.[65]
Since fat tire electric bikes are suitable for a wider variety of situations than a standard cruiser or commuter e-bike, they have the potential to appeal to more people. For example, hunters and campers are ideal candidates for fat tire e-bikes, as they’ll benefit greatly from the heavy-duty tires and powerful motor when they’re navigating difficult wooded trails with lots of gear.
Eight provinces of Canada allow electric power assisted bicycles. In all eight provinces, e-bikes are limited to 500 W output, and cannot travel faster than 32 km/h (20 mph) on motor power alone on level ground.[12] In Alberta prior to July 1, 2009, the limits were 750 W and 35 km/h (22 mph), but presently match federal legislation.[13] Age restrictions vary in Canada. All require an approved helmet. Regulations may or may not require an interlock to prevent use of power when the rider is not pedaling. Some versions (e.g., if capable of operating without pedaling) of e-bikes require drivers' licenses in some provinces and have age restrictions. Vehicle licenses and liability insurance are not required. Generally, they are considered vehicles (like motorcycles and pedal cycles), so are subject to the same rules of the road as regular bicycles. In some cases, regulatory requirements have been complicated by lobbying in respect of the Segway PT.
Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! [14]
EU: EN15194 (EPAC – Electrically Power Assisted Cycles) defines the use pedal-assisted less than 25k/h bikes: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.”
These small complaints prove that the Rad Wagon isn’t perfect. But its overwhelmingly positive qualities clearly outweigh the drawbacks. The Rad Wagon handled beautifully on city streets, accelerating with ease and maintaining a charge for extended range. Rad Power bikes also offers an array of helpful accessories—think racks, baskets, panniers, and platforms—that make the bike nearly as convenient as a car. Time and time again I passed cars stuck in traffic on their daily commute and couldn’t help but wondering: Why don’t more people switch from cars to an e-bike?
At the top end, the 20mph speed limit isn't an absolute, like the speed of light. It's just the most you'll get from the motor. I was able to get it up to 28mph on a flat road (there are no other roads where I live) in Turbo mode and 8th gear, but it took hard work to get there and maintain the speed. The easiest comparison is my mountain bike, where I've hit 23mph on that same stretch of road—and that took a heck of a lot of effort. Exactly how much effort does it take to ride? I have a 15-mile route that I ride on both my mountain bike and cyclecross bike. According to my Apple Watch, I generally burn around 1,400 or so calories on a brisk ride. I'll probably average around 13mph or so on my Marlin and between 16 and 17.5mph on my XO2. I averaged 14.9mph and burned a hair over 1,000 calories with the Bulls Cross E8.
What's the Centros like? Big and heavy, but with enough power to overcome that, it really reminded me of a more upmarket Volt Pulse. You do tend to find that the weightier e-bikes give more of a feeling of speed, even though you're only doing 20mph or so at the absolute most (only up to 15mph with electrical assistance so you'll need leg muscles or a downward incline to get to that outlandish velocity).
The Freedom’s motor gives you five different levels of boost, and the 36-volt battery offers up to 35 miles of range. You can track your power level and speed, as well as your battery life, on a digital display mounted to the handlebar. I have to admit I spent nearly all my time on the Freedom riding in the highest level, where I could pedal up to 19 mph to 20 mph without even breaking a sweat.
In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.
As with all these bikes, the assisted speed is capped at 15mph, but unlike some of them, the Gtech eBike City or its identical (spec-wise) sibling the eBike Sport (this just has a standard frame rather than a step-through one) is light and agile enough for you to be able pedal harder without feeling like the weight is fighting you back down to 15mph. You can even, at a push, use it without the motor on flatter roads.
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:

Solar Shunt firmware: With this firmware the Cycle Analyst can use the auxilliary input as a second current sensor for measuring and showing the solar amps and watts. You can not only see in realtime how much solar power is coming into the pack, you also get combined statistics such as the %solar recharge and the net wh/km mileage taking into account the solar input for the day. This is the ideal instrument for looking at solar ebike performance, consolodating all measurements in a single device.
In Quebec power-assisted bicycles are often classified similarly to standard pedal bicycles. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles. The Quebec Highway Safety Code defines a power-assisted bicycle as a bicycle(2 or 3 wheels that touch the ground) with an electric motor with a maximum power of 500W and a top speed of 32 km/h bearing a specific compliance label permanently attached by the manufacturer[30]. PABs are permitted on the road in the province of Quebec, but riders have to be 14 and over to ride the electric bicycle and if they're under the age of 18, must have a moped or scooter license.
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]

With hand-operated brakes, force is applied to brake levers mounted on the handlebars and transmitted via Bowden cables or hydraulic lines to the friction pads, which apply pressure to the braking surface, causing friction which slows the bicycle down. A rear hub brake may be either hand-operated or pedal-actuated, as in the back pedal coaster brakes which were popular in North America until the 1960s.


European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation. 

The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.
Electric motor assisted bicycles have been banned in the State of New York and are not permitted for on-road use.[50][51] It appears the only known allowance of an electric bicycle is if it is an electric powered moped, at this time. There is a proposed bill to allow ebikes. As of May 2009, Bill A2393("Defines the term electric assisted bicycle") has been passed in the NY State Assembly[52] and its corresponding Bill S4014, sponsored by Senator Thomas Morahan, is before the NY State Senate.[53]
Play it Safe, Make it Easy – E-bike manufacturers will offer you a large variety of styles, types, colors and utility, but the base specifications will be a bike producing less than 750 watts of power (1 horsepower = 746W) , and have its speed limited to 20mph on motor power alone. The majority of US ebikes meet that specification. Manufacturers do this for their own liability. Going this route assures you that your bike was built and sold legally. As a result, you will have about every privilege that a normal bicycle can expect. However, state and local laws may dictate reduced speeds and limited access to bike paths.
Front-Mounted Hub Motor can be found on pre-built bikes or on custom conversions. Mounted to the front wheel, this is the easiest configuration to setup if you’re converting a standard bicycle since there’s no derailleur or chain to worry about. And since most e-bike conversions include batteries mounted to the rear rack, using a front hub motor helps equalize the weight of the bike and makes it easier to handle. But there’s a small risk the motor could cause the front forks to brake. That’s why it’s vital you only use a front hub motor on a steel fork. For pre-built bikes, this shouldn’t be an issue since the motors are usually lower-powered on steel forks.
As of 2005, where Federal funds have been used in the construction of bicycle or pedestrian paths motor vehicles including electric bicycles (here defined as having a motor weighing less than Template:Convert) are not permitted unless State or Local regulations permit [25]. This was known as the Transportation Equity Act for the 21st Century (TEA-21), or Public Law 105-178, or by its 2003 re-authorization which expired in 2005 the Safe, Accountable, Flexible, Efficient Transportation Equity Act (SAFETEA-LU).[26][27]
Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! [14]
Electric motorized bicycles can be power-on-demand, where the motor is activated by a handlebar mounted throttle, and/or a pedelec (from pedal electric), also known as electric assist, where the electric motor is regulated by pedaling. These have a sensor to detect the pedaling speed, the pedaling force, or both. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. Most controllers also provide for manual adjustment.
Range is a key consideration with electric bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. The range of an electric bike is usually stated as somewhere between 7 km (uphill on electric power only) to 70 km (minimum assistance) and is highly dependent on whether or not the bike is tested on flat roads or hills.[14] Some manufacturers, such as the Canadian BionX or American E+ (manufactured by Electric Motion Systems), have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[15] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS.
With a chain drive transmission, a chainring attached to a crank drives the chain, which in turn rotates the rear wheel via the rear sprocket(s) (cassette or freewheel). There are four gearing options: two-speed hub gear integrated with chain ring, up to 3 chain rings, up to 11 sprockets, hub gear built into rear wheel (3-speed to 14-speed). The most common options are either a rear hub or multiple chain rings combined with multiple sprockets (other combinations of options are possible but less common).
Most electric bicycles can be locked using keys supplied by the manufacturer. The key is usually inserted into a switch, which is commonly found on the bicycle's handlebars or on one side of the motor compartment. When switched to the "Off" position, the electrical drive system cannot be turned on. In areas of high risk for bicycle theft, these locking mechanisms are used in conjunction with coil or U locks.
The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop.  They were among the early shops to embrace family friendly cargo bikes and  appreciated the role that electric would play in making cycling more broadly appealing.
Saddles also vary with rider preference, from the cushioned ones favored by short-distance riders to narrower saddles which allow more room for leg swings. Comfort depends on riding position. With comfort bikes and hybrids, cyclists sit high over the seat, their weight directed down onto the saddle, such that a wider and more cushioned saddle is preferable. For racing bikes where the rider is bent over, weight is more evenly distributed between the handlebars and saddle, the hips are flexed, and a narrower and harder saddle is more efficient. Differing saddle designs exist for male and female cyclists, accommodating the genders' differing anatomies and sit bone width measurements, although bikes typically are sold with saddles most appropriate for men. Suspension seat posts and seat springs provide comfort by absorbing shock but can add to the overall weight of the bicycle.

But unlike other battery mounted controllers, the Baserunner also stands on its own too. If you upgrade to a different battery model in the future that doesn't fit the cradle, simply remove the Baserunner from the base and use it as a miniature stand alone controller with your new battery pack. That's Grin thinking about your future options for you.


This year was busy at Haibike’s EUROBIKE stand. The reason: the new FLYON series, which we could only admire behind glass. The new bikes are the spearhead of Haibike’s eMTB development with an exciting and unprecedented level of integration and connectivity. They have a specially developed display, their own remote and, thanks to a 5,000 lumen headlight, are able to turn night into day. To make the rider visible at all times, taillights are neatly integrated into the frame. The bikes also come with the most powerful motor currently available on the market, from TQ Systems. We are sure that many will buy this bike not only for its performance but also as a status symbol.
An electric bicycle is a bicycle with an electric motor used to power the vehicle, or to assist with pedaling. In many parts of the world, electric bicycles are classified as bicycles rather than motor vehicles, so they are not subject to the same laws as motor vehicles. Electric bicycles are one type of motorized bicycle. However, electric bicycles are defined separately and treated as a specific vehicle type in many areas of legal jurisdiction.
×