An itinerant wordsmith with a broad constellation of interests, Lydia Chipman has turned iconoclasm into a livelihood of sorts. Bearing the scars and stripes of an uncommon diversity of experience -- with the notable exceptions of joining a religious order or becoming an artist -- she still can’t resist the temptation to learn something new. Lydia holds a master of arts in English from Georgia Southern University, and a bachelor of arts cum laude in integrative studies from Clayton College. Her expertise is in the areas of robotics, electronics, toys, and outdoors and computer equipment.
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.
I purchased version 2.0 of this device and the manufacturer has been listening to comments from users and making running changes such as the three speeds and the rear suspension. I am an XL size user (6'2", 230lbs) and recently returned from a 26 day cruise around Europe. I rode this little scooter on cobblestones, miles and miles through the Vatican, inside ancient cities and all over the streets of San Juan upon our return stateside. There was only one time it was less than ideal and that was going uphill, on slick tile that was wet from a drizzle. It still make it, just had to lean way forward to get weight on the front wheel.
In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors. Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.
Since 2001, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs). They are currently defined as a two or three wheeled bicycle with an attached electric motor of 500W or less and which is capable of being propelled manually. Furthermore to meet the safety requirements set down by this legislation it must meet the following; when engaged by muscular power it must cease assistance when muscular power ceases or if powered by an accelerator controller cease power when braking and be incapable of providing assistance above 32 km/h and bear a label that is permanently affixed by the manufacturer and appears in a conspicuous location stating the vehicle is a power-assisted bicycle.
Electric bikes (also known as e bikes) are perfect for long-distance riding, or when you just don’t feel like giving your full effort. What differentiates them from electric motorcycles is the ability for the rider to pedal the bike at any time, so if you’re riding along and your battery dies, you’re not going to stranded. These are often very valuable bikes, but some models can be more affordable than you might expect, especially when you treat them as a form of transportation as opposed to thinking of the price in terms of regular bicycles.
The Pivot Shuttle breaks the mold when it comes to e-mountain bikes. This ballsy, carbon-frame bike, with Shimano Di2, has 140mm of rear travel, 150mm up front, and a 150mm dropper post. A Shimano STePS e8000 drive unit, paired with a 500Wh battery, provides 20 mph of pedal assist, so you can skip the lift line when you hit the bike park and zip right to the good stuff. The 27.5-inch wheels are nimble and eat up nearly anything in their path, and the massive 2.8-inch tires have huge knobs that grip the trail like Velcro.
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
You are not allowed to drive S-Pedelecs in France even if they are registered legally in your country (e.g. Germany or Switzerland). In other words, if you plan to take your 45h bike that is legal in your country on vacation in another where it is not, you may violate traffic law. Remove the license plate or don't do it. People who commute between countries, are known to hack removable plates with magnets ...
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
Electric trikes have also been produced that conform to the e-bike legislation. These have the benefit of additional low speed stability and are often favored by people with disabilities. Cargo carrying tricycles are also gaining acceptance, with a small but growing number of couriers using them for package deliveries in city centres. Latest designs of these trikes resemble a cross-between a pedal cycle and a small van.
Alberta identifies e-bikes as "power bicycles" and is consistent with the federal definition of "power-assisted bicycle" in MVSR CRC, c 1038 s 2. Motor output must not exceed 500 W (0.671 hp) and e-bikes cannot travel faster than 32 km/h (20 mph). Fully operable pedals are required. No driver's license, vehicle insurance, or vehicle registration is required. Operators must be 12 years of age or older. All operators are required to wear a motorcycle helmet meeting the standards set in AR 122/2009 s 112(2). A passenger is permitted only if the e-bike is equipped with a seat designated for that passenger.
Some e-bikes operate in pedal-assist only, others have a throttle, and some have both. Generally, pedal-assist only bikes will provide multiple power settings to choose from to help customize your ride, while bikes with both throttle and pedal-assist will have limited pedal-assist options. With these bikes, the throttle provides full control (when needed) while pedal assist is just a secondary option, great on straightaways or open road.
On the other hand, the battery doesn’t lock into the bike, which means you can’t just leave it on your bike when you park at the bike rack. Anyone could walk by and simply remove your battery. That seems like an oversight to me, though perhaps the designers assumed that such a small battery would just be easy to take with you. And it is. My wife could probably lose this battery in her purse.
Arkansas does not define E-bikes. The following definition describes a combustion engine. E-bikes being electric do not have a cylinder capacity and thus this law is not technically applicable. The state defines a "Motorized bicycle" as "a bicycle with an automatic transmission and a motor of less than 50cc." Riders require either a certificate to operate a motorized bicycle, a motorcycle license, a motor-driven cycle license, or a license of class A, B, C or D. Certificates cannot be issued to riders under 10 years of age.
I would add that the point of the article seems to encourage ebikers to “know the state laws” and be confident within those boundaries. To D McCarthy’s question, if your state has a definition for ebikes and classifies them as bicycles and affords access as bicycles, AND, your particular ebike is built within those specifications, then you should be able to ride that section of road with confidence. Just my 2C.
This is an unofficial guide to the laws governing electric bicycles in the United States as of 2016. It was contributed by a guest writer The Smart Ped`aleck who was paid and remains unaffiliated with any electric bicycle company. It may be updated ongoing and is cited throughout with reference links and attributions at the end. It is designed to be an entertaining starting point for understanding the space, digging deeper and in turn choosing the best electric bike platform for your needs.
Over the last few years, I’ve taken my love of the outdoors, hiking, skiing, trekking and exploring to the next level by starting this site. I started a bike shop in Denver, CO, and have seen amazing growth over the last few years. Getting paid to do what I love has been a dream come true for me. That’s also what led me to start BikesReviewed.com. In my shop, I spend a large amount of time helping people find the perfect bike for them and the style of biking they’re going to be doing. It only made sense that I expanded my reach and got online, making it possible for me to help people all over the world. If biking and staying fit is your priority, too, you’ve come to the right place.
Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour Helmets are required.
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
The first mechanically-propelled, two-wheeled vehicle may have been built by Kirkpatrick MacMillan, a Scottish blacksmith, in 1839, although the claim is often disputed. He is also associated with the first recorded instance of a cycling traffic offense, when a Glasgow newspaper in 1842 reported an accident in which an anonymous "gentleman from Dumfries-shire... bestride a velocipede... of ingenious design" knocked over a little girl in Glasgow and was fined five shillings.
However, laws and terminology are diverse. Some countries have national regulations but leave the legality of road use for states and provinces to decide. Municipal laws and restrictions add further complications. Systems of classification and nomenclature also vary. Jurisdictions may address "power-assisted bicycle" (Canada) or "power-assisted cycle" (United Kingdom) or "electric pedal-assisted cycles" (European Union) or simply "electric bicycles". Some classify pedelecs as distinct from other bikes using electric power. Thus, the same hardware may be subject to many different classifications and regulations.
Many newer or smaller companies only design and market their products; the actual production is done by Asian companies. For example, some 60% of the world's bicycles are now being made in China. Despite this shift in production, as nations such as China and India become more wealthy, their own use of bicycles has declined due to the increasing affordability of cars and motorcycles. One of the major reasons for the proliferation of Chinese-made bicycles in foreign markets is the lower cost of labor in China.
The oldest patent for an electric bike I've been able to find at the US Patent and Trademark Office is this one, by Ogden Bolton, Jr. of Canton Ohio, which was filed in September 1895 and granted three months later. You can see from these original diagrams that it bears an amazingly close resemblance to modern electric bikes. In the general picture on the left, you can see there's a hub motor on the rear wheel (blue), a battery suspended from the frame (red), and a simple handlebar control to make the thing stop and go. In the more detailed cutaway of the hub motor on the right, you can see there's a six-pole magnet in the center (orange) bolted to the frame and an armature (made from coiled wire, yellow) that rotates around it when the current is switched on. It's quite a hefty motor even by modern standards; Ogdon mentions "a heavy current at low voltage—for instance, to carry one hundred amperes at ten volts." So that's 1000 watts, which is about twice the power of a typical modern bike hub motor.
There is a lot of information on the internet about electric bikes. Hopefully you have found lots of useful information right here, on this website. Based on this information, you may already have a preference for a specific electric bicycle and / or (technical) components. Your friends that ride e-bikes can also advise you based on their own experiences. But there is only one way you will know if you really make the right choice: take a test drive. During a test drive you will discover how close the riding experience is to your expectations.
In most jurisdictions, bicycles must have functioning front and rear lights when ridden after dark. As some generator or dynamo-driven lamps only operate while moving, rear reflectors are frequently also mandatory. Since a moving bicycle makes little noise, some countries insist that bicycles have a warning bell for use when approaching pedestrians, equestrians, and other cyclists, though sometimes a car horn can be used when a 12 volt battery is available.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015. The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.
The Freedom’s motor gives you five different levels of boost, and the 36-volt battery offers up to 35 miles of range. You can track your power level and speed, as well as your battery life, on a digital display mounted to the handlebar. I have to admit I spent nearly all my time on the Freedom riding in the highest level, where I could pedal up to 19 mph to 20 mph without even breaking a sweat.
E-bikes can boost bike usage, offer health benefits and use “an order of magnitude less carbon dioxide than a car traveling the same distance,” according to a 2016 research review published in the journal Transport Reviews. In fact, access to an e-bike increased cycling trips and distances traveled – and nearly doubled the bike as a mode of transportation, observed one Norwegian study.
Hmm, that’s unfortunate. I actually have a doctors note that I carry along which recommends the use of an assisted bicycle. I ride thoughtfully and have never been asked to show it. I cannot comment on the federal parks, perhaps they are not aware of the federal law classifying electric assist bikes that perform at or below 20 mph and 750 watts as bicycles. Having a note and this information would be a good response if you were questioned.
This is one of the most incredible eBikes on the market today! The Riese and Muller SuperCharger Rohloff GX is one of our most popular models and we know they are being put through thousands of miles across the Southeast. From the coastal areas to the Appalachian mountains, we have customers buying and riding these highly engineered eBikes. These eBikes …
There's no question that electric bikes are far better for the environment than petrol-powered car engines. But that doesn't mean they're completely perfect. Making and disposing of batteries can be very polluting. Not only that, but an electric bicycle is still using energy that has to come from somewhere. You may think you're using clean green power, but the electricity you use for getting about might have come from a filthy old, coal-fired power plant or one driven by nuclear energy. (If you're lucky, of course, it might have come from solar panels or a wind turbine!) Electric bikes are nowhere near as environmentally friendly as ordinary push bikes, but nothing is ever perfect—and, as people often say, "the perfect is the enemy of the good." Electric bikes are certainly a step in the right direction. If everyone used them to get about instead of cars, global warming might be less of a problem, and the world would be a far cleaner and healthier place!
Beginning January 1, 2017, manufacturers and distributors of electric bicycles will be required to apply a label that is permanently affixed, in a prominent location, to each electric bicycle, indicating its class. Should a user "tamper with or modify" an electric bicycle, changing the speed capability, they must replace the label indicating the classification.
When last checked, no E-bikes satisfied this requirement, so ebikes cannot be registered in New Jersey. However, NJ Bill A2581, introduced March 22, 2010, would permit the use of low-speed electric bicycles upon the roadways and bicycle paths in NJ, where a low-speed electric bicycle is defined as a two-wheeled vehicle with fully operable pedals for human propulsion and an electric motor of less than 100 pounds and 750 watts, whose maximum speed on a paved level surface is less than 20 miles per hour. The bill has been referred to the state's Assembly Transportation, Public Works and Independent Authorities Committee.
Experiments done in Uganda, Tanzania, and Sri Lanka on hundreds of households have shown that a bicycle can increase a poor family's income as much as 35%.[better source needed] Transport, if analyzed for the cost-benefit analysis for rural poverty alleviation, has given one of the best returns in this regard. For example, road investments in India were a staggering 3–10 times more effective than almost all other investments and subsidies in rural economy in the decade of the 1990s. What a road does at a macro level to increase transport, the bicycle supports at the micro level. The bicycle, in that sense, can be an important poverty-eradication tool in poor nations.
What's the Centros like? Big and heavy, but with enough power to overcome that, it really reminded me of a more upmarket Volt Pulse. You do tend to find that the weightier e-bikes give more of a feeling of speed, even though you're only doing 20mph or so at the absolute most (only up to 15mph with electrical assistance so you'll need leg muscles or a downward incline to get to that outlandish velocity).
Haibike ships the HardNine with 29-inch tires, 180-millimeter hydraulic disc brakes, a 100-millimeter front suspension fork, and a nine-speed Shimano shifting system. The bike’s LCD readout is affixed to the handlebars and displays the current speed, level of charge, remaining range, and current pedal assist mode. The company says the battery can be completely recharged in just four hours, minimizing downtime between rides.