The electric bike revolution is spreading across the continent, 2017 data clearly underlines that eBikes are the preferred mode of mobility. 720,000 eBikes were sold in Germany, and KTM are one of the largest producers in their native country. As the market prospers, more and more manufacturers are jumping on the bandwagon than ever. KTM … Continue reading Best KTM eBikes 2018 – The Fully Charged Picks
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and completely legal in Canada since early 2001. In November 2005 "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4 2006 the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario. 
Electric bikes are here in a big way. Liberated from some of the normal constraints of standard bike design like weight and gearing, e-bike design has exploded; if you can imagine it, someone has built it. From cargo bikes to city bikes, messenger bikes to mountain bikes, road bikes, folding bikes, and even beach cruisers, there is something for everyone. The beauty of e-bikes is that they make the joy of cycling accessible to so many people in so many ways.
The two most common electric motor styles used in today’s e-bikes are hub motors and mid-drive motors. The Freedom uses a hub motor, which was located in the center of the rear wheel. Hub motors typically don’t offer the same natural maneuverability as the increasingly more common (and more expensive) mid-drive motors because their weight is concentrated in the rear of the bike. It can be jarring when the motor prevents you from going faster than the allotted speed, especially when cruising downhill, but 20 mph is the legal maximum for e-bikes in the US. (In the EU, it’s even lower: 25 km/h, or 15.5 mph.)
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.
State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.
It is very important that sensors work well and that they are integrated/tuned for good usability. Although ebikes do need some initial mental adjustment from riders, some model do much better then others, e.g. most testers seem to prefer the TDS Impluse over the Stöckli E.T. over the Stromer (which model?) with respect to reactivity. Of course, usability is subjective and some people may prefer one behavior over an other. However, cheap bikes may be just plain bad and this is why test driving is important.
Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.
Vehicles with an electric power and power of less than 300W are classified as "not a motor vehicle". Such electric bicycles must comply with the same rules as bicycles. You must wear a helmet even on a scooter or bike under 300W. If the power is over 300W or a combustion engine is used it is a "low powered vehicle" and the moped rules apply. Specifically, a drivers license and registration are required.
E-bikes use rechargeable batteries, electric motors and some form of control. Battery systems in use include sealed lead-acid (SLA), nickel-cadmium (NiCad), nickel-metal hydride (NiMH) or lithium-ion polymer (Li-ion). Batteries vary according to the voltage, total charge capacity (amp hours), weight, the number of charging cycles before performance degrades, and ability to handle over-voltage charging conditions. The energy costs of operating e-bikes are small, but there can be considerable battery replacement costs. The lifespan of a battery pack varies depending on the type of usage. Shallow discharge/recharge cycles will help extend the overall battery life.
Dryft is a robust, energetic mountain bike, painted in the hues of the setting sun and evening sky. This electric vehicle is designed to take you to those places where no other vehicle can. LightSpeed Dryft an e-Bike that is as fond of adventure as you are. The ideal companion to the thrill seeker in you — wherever you decide to ride, your Dryft always has your back.
Under the doctrine of One Country, Two Systems, Hong Kong has independent traffic law from mainland China. Electric bike are considered as motorcycles in Hong Kong, and therefore needs type approval from the Transport Department as other automobiles. All electric bike availble in Hong Kong fail to meet the type approval requirement, and Transport Department has never granted any type approval for electric bike, making all electric bike effectively illegal in Hong Kong. Even if they got type approved, the driver would need a motorcycle driving license to ride. As a side note, Hong Kong doesn't have a moped vehicle class (and therefore moped driving license), and mopeds are consided as motorcycles too.
During testing—and unlike some of the other bikes I’ve tried—this range held true, with the Rad Wagon handling a 20-plus mile round trip with ease. This is helped by a regenerative braking system that automatically charges the battery whenever you engage the brake levels. It’s also relatively quick to charge back up—taking around four hours in my garage—although Rad Power reports that average time is five to six hours.
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.
In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.
As long as you can do without some of the perks that pricier models offer—like a detailed display unit, integrated lights, and a torque-sensor motor—the August Live! LS is a solid, stable, comfortable, and really freakin’ cute (have you see those polka-dot fenders?) e-bike. Its 8-speed twist shifter, chopper-style handlebar, Touch Down Geometry (for a more laid-back ride), and three levels of assist keep this bike within the realm of “cruiser.” But with a 250-watt Bafang rear-hub motor, a top pedal-assisted speed of 20 mph, and reliable disc brakes, the August is no joke. It’ll get you to the top of relatively steep climbs without forcing you out of the saddle, and it feels super stable on the way back down. It has a battery range of 20 miles, but that’s enough to take it where it’s happiest: tootling along at the beach, around town, and through the park.
A KS LEV Integra dropper post, 130mm of front and rear travel, 27.5-inch wheels, and trail-grabbing 2.8-inch tires make this pedal-assist mountain bike a great option if you want to climb farther to shred longer, but don’t want to lug your bike uphill for ages. The 250-watt motor, placed slightly farther forward than most other bikes to optimize weight distribution and handling, provides a nice boost so you can enjoy the ride up and not be too gassed when you get to the top.
In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear wheel, or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.
The safety bicycle gave women unprecedented mobility, contributing to their emancipation in Western nations. As bicycles became safer and cheaper, more women had access to the personal freedom that bicycles embodied, and so the bicycle came to symbolize the New Woman of the late 19th century, especially in Britain and the United States. The bicycle craze in the 1890s also led to a movement for so-called rational dress, which helped liberate women from corsets and ankle-length skirts and other restrictive garments, substituting the then-shocking bloomers.
The Super Commuter is very aptly named. The 350w Bosch motor will help you sustain speeds of up to 28mph, and the burly, 2.4-inch wide, Schwalbe Super Moto-X 650b tires will keep you secure on even the roughest city streets, and Shimano Deore hydraulic brakes provide ample stopping power. Fenders provide welcome protection from road spray so you arrive at your destination fresh, integrated lights are critical for post-sunset riding, and a side-view mirror hanging on the left side of the handlebar gives a great view of traffic around you. After all, you can ride at the speed of urban traffic on the Super Commuter.
When last checked, no E-bikes satisfied this requirement, so ebikes cannot be registered in New Jersey. However, NJ Bill A2581, introduced March 22, 2010, would permit the use of low-speed electric bicycles upon the roadways and bicycle paths in NJ, where a low-speed electric bicycle is defined as a two-wheeled vehicle with fully operable pedals for human propulsion and an electric motor of less than 100 pounds and 750 watts, whose maximum speed on a paved level surface is less than 20 miles per hour. The bill has been referred to the state's Assembly Transportation, Public Works and Independent Authorities Committee.
I do not recommend hacking a bike into s-pedelec, i.e. make a 25km/h bike go at 45 or faster. If you have an accident you will be in trouble. Just get a legal version. In addition you will have good insurance. Of course, in countries like France or the UK that so far do not know S-Pedelecs, you will have to make a difficult moral choice.... At least, make sure that your rig is safe...
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.
Included in this shipment are the much awaited 3540 motors with their slick "UFO" design. These are the replacements for the older square style "H" motors, you may have noticed that this change was implemented last year with the 3525 front and rear motors. As always, we have the motors customized with a 10K NTC thermistor for thermal rollback using the CA3.
Electrically-assisted cycles are usually classified as either pedelecs or e-bikes. Under European Union regulations adopted in the UK in June 2003, only power-assisted cycles meeting the pedelec classification are considered to be pedal cycles. The maximum power allowed in the European Union for (pedelec) electric bicycles is 250 W, with a maximum assisted speed of 25 km/h.. To meet the pedelec specification the electric motor must be activated by the rider's pedalling effort and the power must cut out completely whenever the rider stops pedalling. Control of the motor by pedalling is often the key difference between a pedelec and e-bike.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
Most of you are likely here for the electric bits, though. Those consist of a 500Wh user-swappable Bosch Powerpack battery and a 250W Bosch Active Line Plus motor that delivers 37lb-ft (50Nm) of torque and speeds of up to 20mph (32km/h). The battery takes up to 4.5 hours to reach a 100-percent charge and offers a range of up to 134 miles. With the battery and motor, it's markedly heavier than a comparable urban bike, weighing in at 46lb (20.8kg).
On a trip to Palo Alto last year, we had the chance to ride Specialized’s pedal-assisted Turbo Vado and the model is still our favorite ebike on the market. Utilizing a 350-watt motor and 604-watt-hour lithium-ion battery, the Turbo Vado is capable of traveling a whopping 80 miles on a single charge, which should be more than enough for any daily commute with plenty of miles left over.
"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Chapter 551., titled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D. The following definition of electric bicycle was passed by the Texas legislature in 2001. "Electric bicycle" means a bicycle that is designed to be propelled by an electric motor, exclusively or in combination with the application of human power, cannot attain a speed of more than 20 miles per hour without the application of human power; and does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle on a highway that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle on a highway used primarily by pedestrians.
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.
Fast and fun on the trail, the SDURO HardNine handles rough terrain with ease, while its large tires roll over most obstacles without missing a beat. The pedal assist makes for quick, energy-saving climbing and the bike descends surprisingly well, too. Its front suspension provides a nice level of cushion on bumpy trails and while we missed having a full-suspension on this model, that would have added additional weight and costs.
After you decide which style of e-bike you want, consider the class. In the U.S., there are three classes defined by the type of assist and how fast the motor will propel you. Most electric bikes sold are class 1 or 3. Class 1 bikes have a motor (max 750w) that assists while you’re pedaling, up to 20 mph. Class 3, also known as “speed pedelec,” can also have up to a 750w motor, but it can assist you up to 28 mph. Both are allowed in most states and cities without requiring a license. Class 2 models have throttles that don’t require the rider to pedal in order to get a boost. They’re allowed on most streets, bike lanes, and paths, but are less popular than the other classes and not covered much here (because not only do we still love to pedal, we also prefer the greater distances that pedal-assist bikes can cover).
Being member of European Economic Area (EEA), Norway implemented the European Union directive 2002/24/EC. This directive defined legal ebikes for all EU and EEA countries to cycle "with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling." The definition became part of Norwegian vehicle legislation in 2003. A more detailed specification will become effective when the new European ebike product safety standard EN 15194 is published in 2009.
The rest of the bike is equally impressive. Integrated lights in the front and the rear run directly off the main battery, so you’re never replacing coin cells or AAA batteries. And the disc brakes give you plenty of stopping power. The 36-volt battery attaches to the down tube and is designed to be easily removed for recharging. A key-lock at the top of the mount ensures that no one can steal your battery if your bike is left in a public place. And a built-in alarm system, activated with a car-like key fob, is ear-splitting enough to keep thieves away altogether. (Miller promises the alarm’s sensitivity is tuned so it shouldn’t go off if the bike is jostled at a public bike rack, but I didn’t have the bike long enough to test this out.)
They also served to teach the industrial models later adopted, including mechanization and mass production (later copied and adopted by Ford and General Motors), vertical integration (also later copied and adopted by Ford), aggressive advertising (as much as 10% of all advertising in U.S. periodicals in 1898 was by bicycle makers), lobbying for better roads (which had the side benefit of acting as advertising, and of improving sales by providing more places to ride), all first practiced by Pope. In addition, bicycle makers adopted the annual model change (later derided as planned obsolescence, and usually credited to General Motors), which proved very successful.
The Registrar will permit an electric motor driven cycle to be registered if it meets Canada Motor Vehicle Safety Standards (CMVSS) as a Limited Speed Motorcycle, or Scooter as is done with gas powered motor driven cycles. If the vehicle was manufactured after 1988 it will bear a compliance label stating that it meets these standards. The operator will be subject to all the requirements placed on operators of motor driven cycles.
To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885. However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.