Would an e-bike that used a trailing generator to power the electric motor still be considered an e-bike? The purpose of the generator is allow greater distances to be traveled and all day riding. The gen-set that I am looking at uses a 49 cc gas engine with a 12 volt generator, this would be from the ground up build using a 1 hp electric motor. This seems to stay within the state laws of AZ. where I reside. Thanks for your thoughts.
Legislative changes in 2012 significantly altered the classification and regulatory structure for e-bikes. The general effect was to establish electric-assisted bicycles as a subset of bicycles and regulate e-bikes in roughly the same manner as bicycles instead of other motorized devices with two (or three) wheels. Laws 2012, ch. 287, art. 3, §§ 15-17, 21, 23-26, 30, 32-33, and 41. The 2012 Legislature also modified and clarified regulation of e-bikes on bike paths and trails. Laws 2012, ch. 287, art. 4, §§ 1-4, 20.
Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! 
GPS Firmware: This net update will be much appreciated by people who have a GPS Analogger device with their CA3. With a simple hardware modification to the Analogger circuit, the GPS data will be transmitted from your existing TRS cable back to the Cycle Analyst. You can then see the time of day, your elevation, position, and direction all on the CA3 screen. The firmware also features additional custom views on the main screen, allowing you to replace or toggle the battery voltage with any of these new parameters to get just the display you are after.
The last 8 months we've been wrapping up some long duration testing of Statorade across different hub motor lines and performing experiments confirming its long term stability. These results have us pumped to introduce this motor cooling solution beyond DIY'ers and into wider markets. As an example, have a look at the video we below showing the effect this has on a small direct drive folding bike motor.
E-bike usage worldwide has experienced rapid growth since 1998. In 2016 there were 210 million electric bikes worldwide used daily. It is estimated that there were roughly 120 million e-bikes in China in early 2010, and sales are expanding rapidly in India, the United States of America, Germany, the Netherlands, and Switzerland. A total of 700,000 e-bikes were sold in Europe in 2010, up from 200,000 in 2007 and 500,000 units in 2009.
Every inch of the bike is thought through, from how the simple, rugged battery connection to the hydraulic disc brakes to the tire choice, to the adorable little bell. The custom battery shape works aesthetically with the frame and is not some obtrusive piece strapped to the down tube of the bike. By putting it down low, it also adds to the stability of the bike, making it handle like a dream, regardless of speed.
Pedelecs are much like conventional bicycles in use and function — the electric motor only provides assistance, for example, when the rider is climbing or struggling against a headwind. Pedelecs are therefore especially useful for people in hilly areas where riding a bike would prove too strenuous for many to consider taking up cycling as a daily means of transport. They are also useful for riders who more generally need some assistance, e.g. for people with heart, leg muscle or knee joint issues.
The company was founded in 2009 by Tora Harris who graduated from Princeton University with a degree in Mechanical and Aerospace Engineering. While at Princeton, Harris ran track and became a 2-time winner of the NCAA Championship in the High Jump and set several Ivy League track records in the process. Harris went on to win 2 USA National Outdoor Championship Titles and competed in the 2004 Athens Olympic Games.
Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.
Bike is awesome, warranty support has so far delivered, but is a hassle to deal with (and hassle is acceptable and better than nightmare, or unresponsive/clueless/unhelpful/not-english-speaking). To be fair, this is the middle of Swag's busy season. Check tire inflation, check and tighten fasteners, seatpost and handlebars and stem out of the box, RTFM, charge the battery and you're out the door riding quickly.
E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
As of 2008 a standard class C license, proof of insurance, and registration (annual fee: $9.00) are required for operation of any motorized pedalcycle in Pennsylvania. Additionally, there are strict equipment standards that must be met for operation, including: handlebars, brakes, tires/wheels, electrical systems/lighting, mirrors, speedometer, and horns/warning devices.
Fast and fun on the trail, the SDURO HardNine handles rough terrain with ease, while its large tires roll over most obstacles without missing a beat. The pedal assist makes for quick, energy-saving climbing and the bike descends surprisingly well, too. Its front suspension provides a nice level of cushion on bumpy trails and while we missed having a full-suspension on this model, that would have added additional weight and costs.
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
I bought this bike from a dealer after extensive research on ebikes. The Elby is on par with European commuter ebikes at a better price point, you get a lot for your $ here. Elby is the complete package commuter: lights & a USB charger (for a phone or whatever) are integrated into the motor’s power supply and wired inside the frame. Rugged fenders have heavy-duty cross braces to attach baskets and whatnot. Thick Continental tires make for a comfy ride. The step-through frame is very convenient, built stout enough to carry me (200#) and two loaded baskets down hills and around curves with perfect stability. The motor on this bike is in the rear hub, and having it behind me makes it virtually soundless. The motor (BionX 500 watt) kicks in as soon as you start pedaling, but there is a