"Bicycle" means either of the following: (1) A device having two wheels and having at least one saddle or seat for the use of a rider which is propelled by human power. (2) A device having two or three wheels with fully operable pedals and an electric motor of less than 750 watts (one horsepower), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden, is less than 20 miles per hour.
Some US companies, notably in the tech sector, are developing both innovative cycle designs and cycle-friendliness in the workplace. Foursquare, whose CEO Dennis Crowley "pedaled to pitch meetings ... [when he] was raising money from venture capitalists" on a two-wheeler, chose a new location for its New York headquarters "based on where biking would be easy". Parking in the office was also integral to HQ planning. Mitchell Moss, who runs the Rudin Center for Transportation Policy & Management at New York University, said in 2012: "Biking has become the mode of choice for the educated high tech worker".
Electric bicycles use rechargeable batteries, electric motors and some form of control. This can be a simple as an on-off switch but is more usually an electronic pulse width modulation control. Electric bicycles developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains. The bicycles were then charged from the mains, as is common today. Battery systems in use include lead-acid, NiCd, NiMH and Li-ion batteries.
Bicycles were introduced in the late 19th century in Europe, and by the early 21st century, more than 1 billion were in existence at a given time. These numbers far exceed the number of cars, both in total and ranked by the number of individual models produced. They are the principal means of transportation in many regions. They also provide a popular form of recreation, and have been adapted for use as children's toys, general fitness, military and police applications, courier services, bicycle racing and bicycle stunts.
Even the humble bicycle hasn't escaped the clutches of modern technology. A whole herd of new e-bikes with electric motors are taking to our cities' streets. Adding a motor to a standard cycle does ramp up the price significantly, but it takes much of the effort out of cycling, making your commute to the office a sweat-free experience and allowing you to sit back and enjoy your suburban cruise.
None of this would matter if the VanMoof Electrified S2 (and its close relative the X2) wasn't fun to ride, but it is a blast. Like the Brompton, it pulls off the neat trick of powering you along but giving the illusion that you're doing the work, reacting quickly and cleverly to the speed of your pedalling and the difficulty of any incline you're on.
The handlebars connect to the stem that connects to the fork that connects to the front wheel, and the whole assembly connects to the bike and rotates about the steering axis via the headset bearings. Three styles of handlebar are common. Upright handlebars, the norm in Europe and elsewhere until the 1970s, curve gently back toward the rider, offering a natural grip and comfortable upright position. Drop handlebars "drop" as they curve forward and down, offering the cyclist best braking power from a more aerodynamic "crouched" position, as well as more upright positions in which the hands grip the brake lever mounts, the forward curves, or the upper flat sections for increasingly upright postures. Mountain bikes generally feature a 'straight handlebar' or 'riser bar' with varying degrees of sweep backwards and centimeters rise upwards, as well as wider widths which can provide better handling due to increased leverage against the wheel.
During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.
Today, China is the world's leading producer of electric bicycles. According to the data of the China Bicycle Association, a government-chartered industry group, in 2004 China's manufacturers sold 7.5 million electric bicycles nationwide, which was almost twice the year 2003 sales; domestic sales reached 10 million in 2005, and 16 to 18 million in 2006. By 2007, electric bicycles were thought to make up 10 to 20 percent of all two-wheeled vehicles on the streets of many major cities. A typical unit requires 8 hours to charge the battery, which provides the range of 25–30 miles (40–50 km), at the speed of around 20 km/h.
Some countries require child and/or adult cyclists to wear helmets, as this may protect riders from head trauma. Countries which require adult cyclists to wear helmets include Spain, New Zealand and Australia. Mandatory helmet wearing is one of the most controversial topics in the cycling world, with proponents arguing that it reduces head injuries and thus is an acceptable requirement, while opponents argue that by making cycling seem more dangerous and cumbersome, it reduces cyclist numbers on the streets, creating an overall negative health effect (fewer people cycling for their own health, and the remaining cyclists being more exposed through a reversed safety in numbers effect).
There's no question that electric bikes are far better for the environment than petrol-powered car engines. But that doesn't mean they're completely perfect. Making and disposing of batteries can be very polluting. Not only that, but an electric bicycle is still using energy that has to come from somewhere. You may think you're using clean green power, but the electricity you use for getting about might have come from a filthy old, coal-fired power plant or one driven by nuclear energy. (If you're lucky, of course, it might have come from solar panels or a wind turbine!) Electric bikes are nowhere near as environmentally friendly as ordinary push bikes, but nothing is ever perfect—and, as people often say, "the perfect is the enemy of the good." Electric bikes are certainly a step in the right direction. If everyone used them to get about instead of cars, global warming might be less of a problem, and the world would be a far cleaner and healthier place!
UPDATE (2019-03-15): I've now got more than 110 miles on the bike and still loving it. The longest ride I did was 28.5 miles and the display was still showing about two bars left on the battery. But the battery gauge is not accurate. Even when it went down to two bars it would also jump back up to 4 bars and stay that way for awhile. So it's really hard to tell how much power you have left. On one ride, after 14 miles the pedal assist stopped working all of a sudden. I stopped and re-seated the cadence sensor and it started working again. Even when PAS didn't work the throttle was still working. It hasn't happened since. There was also a lot of rattling noises which I found was the battery rattling around in the mounting bracket.
If you have dynamo-powered bicycle lights, you already own an electric-powered bicycle! Consider: as you pump your legs up and down on the pedals, you make the wheels rotate. A small dynamo (generator) mounted on the rear wheel produces a tiny current of electricity that keeps your back safety lamp lit in the dark. Now suppose you could run this process backward. What if you removed the lamp and replaced it with a large battery. The battery would kick out a steady electric current, driving the dynamo in reverse so that it spun around like an electric motor. As the dynamo/motor turned, it would rotate the tire and make the bike go along without any help from your pedaling. Hey presto: an electric bike! It may sound a bit far-fetched, but this is more or less exactly how electric bikes work.
Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.
In 5 years of working as a bike messenger in Minneapolis, I've ridden all kinds of bikes, in all kinds of weather. I've ridden walmart mountain bikes, 80's classic steel road bikes, kitted out Treks, pretty much everything EXCEPT for fat tire bikes. Such wide tires always seemed... too much. No need for a bike that only makes itself worthwhile maybe two months out of the year, I thought.
The definition was clearly written with gasoline-powered pedalcycles in mind. The requirement of an automatic transmission is troublesome for those who just want to add an electric-assist motor to a bicycle, for almost all bicycles have transmissions consisting of chains and manually shifted sprockets. The registration form asks for a VIN, making it difficult to register some foreign-made ebikes. The fine for riding an unregistered electric bike is approximately $160.00 per event as of 2007.
Yes, there are less expensive ebikes on the market but most come with a few serious caveats. The Espin Sport delivers on the full promise of an electric bike, but in a more affordable fashion. This bike isn’t going to tow you around for a 60-mile round-trip endeavor but those seeking their first ebike will get plenty of return on their investment with this model.
Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.
But if you're someone who loves riding, commutes to work on a bike, or has a gig that requires you to spend a lot of time in the saddle, you might want to look at electric bikes. You'll be able to go farther, faster, and expend less energy riding one. And if electric bikes are for you, look hard at the Cross E8 Step-Thru. It's an incredibly well-made, well-thought-out electric bike. Strip away the battery, motor, and computer, and you'd still be left with a really good cycle.
It is important to note that if a vehicle has an electric motor greater than 500 watts and is capable of powering the vehicle when traveling at a speed greater than 32 km/h and it does not have a CMVSS compliance label it cannot be registered unless the owner can prove, by having the vehicle certified by an engineer, that it is safe for operation on NB highways. Also, not all vehicles are suitable for operation on NB highways and it could be that the vehicle in question may not be a motor driven cycle or a bicycle and cannot be operated on the highway at all.
While we're still fairly new to the solar ebike game, Mark is among the (suprisingly numerous) Grin customers who've been thinking about and experimenting with solar bikes for many years. After he shared pictures of his latest project and mentioned his round the world touring ambitions, we thought we had to do a small feature on this guy. A quick last minute trip to Maker Faire was arranged to meet up, and here we present, Mark Havran:
It should be noted that the definition as written does not define the power of the motor in Watts as is conventionally done for electric bicycles but rather in brake horsepower. Thus for an electric bicycle, motor kit, or electric bicycle motor that is not rated by the manufacture in brake horsepower but rather in Watts a conversion must be made in the units a conversion which is not given in the code of the law and thus the court will have to consider a factor of conversion that is not directly encoded in the law. Industry standard conversion for Watts to horsepower for electric motors is 1 horsepower = 746 watts. Acceptance of that conversion factor from industry, however, as interpretation of the law is subject to the process of the courts since it is not defined specifically in the law.
For those who missed seeing it live, we've also uploaded a youtube video of our live demonstration of a regular bike being converted over to electric assist. We hope that this helps demystify the process for some considering their first kit purchase. It was a fun opportunity as the owner of the bike was at the show and could ride it away the next day.
“Changes in production and consumption patterns are a crucial element of the sustainability agenda. Communication between product developers and users, and user integration in product development, can serve as a means for organizational as well as individual learning processes, resulting in sustainable product development. [...] Improved methods, such as INNOCOPE (innovating through consumer-integrated product development), tested in this study with a cycle manufacturer and resulting in a new product, a pedelec, are needed for effective communication, activating consumers and enabling them to promote sustainability goals. Through co-operative product development processes key factors facilitating and obstructing the adoption of sustainable innovations may be identified. Such processes can enhance the emergence and diffusion of sustainable product innovations and different forms and bodies of knowledge can be combined. Integrating users' contextual everyday knowledge of the product with the technical knowledge of companies may lead to mutual learning, technical innovations and changes in consumer behaviour.” (Hoffmann, 2007).
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.
Maryland defines an "electric bicycle" as a vehicle that (1) is designed to be operated by human power with the assistance of an electric motor, (2) is equipped with fully operable pedals, (3) has two or three wheels, (4) has a motor with a rating of 500 watts or less, (5) and is capable of a maximum speed of 20 miles per hour on a level surface when powered by the motor. (Senate Bill 379, approved by the Governor 5/5/2014, Chapter 294.)  This legislation excludes "electric bicycle" from the definition of "moped", "motorized minibike", and "motor vehicle", and removes the titling and insurance requirements required for electric bicycles under prior Maryland law.
The Tidalforce Electric Bicycle was an electric bicycle manufactured by Wavecrest Labs from 2003 until the company went out of business in 2006. All models of Wavecrest Tidalforce electric bikes have a 36 volt electric hub motor built into the rear wheel hub and a 36 volt battery pack built into the front wheel hub. Wavecrest Labs manufactured three models of Tidalforce bikes: The Wavecrest Tidalforce M-750, the S-750 Traditional hard tail mountain bike and the iO-750 Cruiser. Any of the three bikes with an X suffix denotes that the motor is a 1000 watt motor without a set speed restriction as compared to the speed limited 750 watt version.
Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).
And let’s not forget the economic advantages of owning an e-bike. The annual cost of running a new family car is, on average, about $9,000 per year. Running an electric bike costs around $400 per year. And while filling a gas tank costs around $30, recharging an electric bike battery costs only about 50 cents. A tank of gas may get you further, but not 60 times further!
The Class 3 Aventon Pace 500 urban e-bike has five levels of pedal assist and tops out at 28 mph. But the Pace has something not found on a lot of modern e-bikes. In addition to pedal power, it also has a throttle—in the case of the Pace, a small thumb paddle on the left side of the handlebar next to the control unit that holds at a steady 20 mph, no pedaling required. The bike itself has an aluminum frame, a swept-back handlebar, ergo grips, a sturdy kickstand, hydraulic disc brakes, 8-speed Shimano Altus shifting and gearing, 27.5x2.2-inch Kenda e-bike-rated tires, a saddle the size of Texas, and good ol’ classic city/commuter-bike geometry. It doesn’t come equipped with fenders or a rear rack, but you can add them. Power comes in the form of a 500-watt rear-hub motor, a semi-integrated battery on the down tube (with a range of up to 50 miles), and a backlit display unit mounted on the stem.