In 5 years of working as a bike messenger in Minneapolis, I've ridden all kinds of bikes, in all kinds of weather. I've ridden walmart mountain bikes, 80's classic steel road bikes, kitted out Treks, pretty much everything EXCEPT for fat tire bikes. Such wide tires always seemed... too much. No need for a bike that only makes itself worthwhile maybe two months out of the year, I thought.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.
Simple, convenient, cheap, and economical—bicycles are one of the world's favorite forms of transportation. But they're not for everyone. They can be hard to pedal up and down hills or with heavy loads, and elderly or disabled people may find them impossible to manage. In the last few years, a new generation of electric bicycles has begun to revolutionize our idea of environmentally friendly transportation. These new cycles have all the convenience of cars with all the simple economy of ordinary cycles. Let's take a closer look at how they work.
E-bikes are zero-emissions vehicles, as they emit no combustion by-products. However, the environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, e-bikes are claimed to have a significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.
E-bikes are classified in three different types: Class 1 and Class 3 bikes are powered proportionally to the “input” a rider gives via pedaling. “It feels natural, and you’re still riding a bike, so all your reflexes, skill and comfort you’ve developed over years of riding bikes apply immediately,” says Fritz Rice, sales manager of Gregg’s Cycles, near Greenlake.
In the 1870s many cycling clubs flourished. They were popular in a time when there were not cars on the market and the principal mode of transportation was horse-drawn vehicles, such the horse and buggy or the horsecar. Among the earliest clubs was The Bicycle Touring Club, which has operated since 1878. By the turn of the century, cycling clubs flourished on both sides of the Atlantic, and touring and racing became widely popular. The Raleigh Bicycle Company was founded in Nottingham, England in 1888. It became the biggest bicycle manufacturing company in the world, making over two million bikes per year.
Alberta identifies e-bikes as "power bicycles" and is consistent with the federal definition of "power-assisted bicycle" in MVSR CRC, c 1038 s 2. Motor output must not exceed 500 W (0.671 hp) and e-bikes cannot travel faster than 32 km/h (20 mph). Fully operable pedals are required. No driver's license, vehicle insurance, or vehicle registration is required. Operators must be 12 years of age or older. All operators are required to wear a motorcycle helmet meeting the standards set in AR 122/2009 s 112(2). A passenger is permitted only if the e-bike is equipped with a seat designated for that passenger.
Before you start shopping around for a new e-bike, the first thing you should ask yourself is, “how do I plan on using an electric bicycle?” How far do you plan on traveling? What type of terrain will you be traveling on? How much assistance do you need? Do you plan on pedaling – or do you want the bike to do all the work? Is this bike for daily commuting or casual riding? How fast do you need to go?
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
It’s a topic that many eMTBers are interested in: fast charging. What has long been a reality with electric cars is now also being partly improved for ebikes with high amperage chargers. Bosch has presented a 6A charger this year that can charge a 500 Wh battery in 3 hours, more than a third faster than the standard charger. The new benchmark next year, however, will probably be the 10A charger presented by Haibike and BMZ. It is claimed to be capable of charging a 630 Wh battery in just 1.5 hours.
Since 2001, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs). They are currently defined as a two or three wheeled bicycle with an attached electric motor of 500W or less and which is capable of being propelled manually. Furthermore to meet the safety requirements set down by this legislation it must meet the following; when engaged by muscular power it must cease assistance when muscular power ceases or if powered by an accelerator controller cease power when braking and be incapable of providing assistance above 32 km/h and bear a label that is permanently affixed by the manufacturer and appears in a conspicuous location stating the vehicle is a power-assisted bicycle.
The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations. The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.