This is list of the best performing, best value electric bikes for 2018 / 2019. For each category I list two models, the first recommendation is based on performance and the second is based on affordability. As you explore the list and get to know EBR, check out the ebike community forum for more personalized feedback. Share your height, weight, budget and intended use (along with bikes you like) to get advice from actual owners and moderators.

Electric-assist and other "motorized bicycles"[86] do not need to be inspected, do not require a license, and do not require registration. The vehicle must meet all of the following criteria: a post mounted seat for each person it is designed to carry, two or three wheels which contact the ground, fully operative pedals, wheels at least 16 inches in diameter and a motor not capable of propelling the device at more than 20 mph on level ground. The driver does not need a license, but must be at least 16 years old. DC law prohibits motorized bicycles from traveling anywhere on the sidewalk or in the bike lanes. DC Regulation 18-1201.18 provides: "Except as otherwise permitted for a motor vehicle, no person shall operate a motorized bicycle on any sidewalk or any off-street bikepath or bicycle route within the District. This prohibition shall apply even though the motorized bicycle is being operated solely by human power." So, if cars are prohibited in a particular place, motor-assisted bikes are also prohibited.[87]
In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors.[1] Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.
The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead.  

Electric bicycle usage worldwide has experienced rapid growth since 1998. It is estimated that there were roughly 120 million "ebikes" on the road in China as of early 2010.[1]. The “Electric Bikes Worldwide Reports – 2010 Update”[2] estimates that 1,000,000 electric bicycles will be sold in Europe in 2010. The same report estimates that sales in the USA will reach roughly 300,000 in 2010, doubling the number sold in 2009.

Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.

E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.

A human traveling on a bicycle at low to medium speeds of around 16–24 km/h (10–15 mph) uses only the power required to walk. Air drag, which is proportional to the square of speed, requires dramatically higher power outputs as speeds increase. If the rider is sitting upright, the rider's body creates about 75% of the total drag of the bicycle/rider combination. Drag can be reduced by seating the rider in a more aerodynamically streamlined position. Drag can also be reduced by covering the bicycle with an aerodynamic fairing. The fastest recorded unpaced speed on a flat surface is 144.18 km/h (89.59 mph)[41]

Since cyclists' legs are most efficient over a narrow range of pedaling speeds, or cadence, a variable gear ratio helps a cyclist to maintain an optimum pedalling speed while covering varied terrain. Some, mainly utility, bicycles use hub gears with between 3 and 14 ratios, but most use the generally more efficient dérailleur system, by which the chain is moved between different cogs called chainrings and sprockets in order to select a ratio. A dérailleur system normally has two dérailleurs, or mechs, one at the front to select the chainring and another at the back to select the sprocket. Most bikes have two or three chainrings, and from 5 to 11 sprockets on the back, with the number of theoretical gears calculated by multiplying front by back. In reality, many gears overlap or require the chain to run diagonally, so the number of usable gears is fewer.
Being member of European Economic Area (EEA), Norway implemented the European Union directive 2002/24/EC. This directive defined legal ebikes for all EU and EEA countries to "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.” The definition became part of Norwegian vehicle legislation[17] in 2003. A more detailed specification will become effective when the new European ebike product safety standard EN 15194 is published in 2009.

But the whole is also influenced by the sensory systems which are very different from model to model. E.g. A typical 2013 Panasonic system requires pedalling for optimal support (55/minute?) and has both a pedalling frequency and a speed sensor. You don't get much assistance if you pedal very slowly or very fast. Typically, a rear motor has a force sensor, i.e. you get lots of support fast when you start pedalling in a low gear, i.e. it will "feel" your need for assistance.
None of this would matter if the VanMoof Electrified S2 (and its close relative the X2) wasn't fun to ride, but it is a blast. Like the Brompton, it pulls off the neat trick of powering you along but giving the illusion that you're doing the work, reacting quickly and cleverly to the speed of your pedalling and the difficulty of any incline you're on. 
An itinerant wordsmith with a broad constellation of interests, Lydia Chipman has turned iconoclasm into a livelihood of sorts. Bearing the scars and stripes of an uncommon diversity of experience -- with the notable exceptions of joining a religious order or becoming an artist -- she still can’t resist the temptation to learn something new. Lydia holds a master of arts in English from Georgia Southern University, and a bachelor of arts cum laude in integrative studies from Clayton College. Her expertise is in the areas of robotics, electronics, toys, and outdoors and computer equipment.
The Footloose has no chain, however -- it's entirely electrically driven. It takes very little effort to get to your destination, meaning you arrive at work without having broken a sweat. The downside is that when you run out of power, you're not going anywhere. And pedalling from a standstill, waiting for the motor to kick in, is an odd sensation that takes some getting used to.
At just 36V and 5.2 Ah, the battery is not designed for long distance travel. GOTRAX claims the Shift S1 has a range of up to 15 miles (25 km), though that’s only with a lower pedal assist level. If you’re going full throttle, 10 miles (15 km) is a better estimate. But with a battery this small, you could easily charge it at your desk or in the corner of the classroom – lengthening your effective range.
DIY enthusiasts, with tens of thousands of converted bikes using throttle-only, 20+ mph kits, are now officially labeled Moped class. While these bikes handle and pedal-ride just as safely as the class 3 speed pedelecs in many cases, our DIY counterparts will be officially kicked out and left on their own for advocacy and legal acceptance in California. This is a big deal, without a class sticker, any DIY electric bike conversion kit is considered a Moped and not a bicycle.
Range is a key consideration with electric bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. The range of an electric bike is usually stated as somewhere between 7 km (uphill on electric power only) to 70 km (minimum assistance) and is highly dependent on whether or not the bike is tested on flat roads or hills.[14] Some manufacturers, such as the Canadian BionX or American E+ (manufactured by Electric Motion Systems), have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[15] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS.
Beginning January 1, 2017, manufacturers and distributors of electric bicycles will be required to apply a label that is permanently affixed, in a prominent location, to each electric bicycle, indicating its class. Should a user "tamper with or modify" an electric bicycle, changing the speed capability, they must replace the label indicating the classification.
Powered by a 250-watt Brose Centerdrive system, the Redux is capable of reaching speeds of up to 28 mph, which comes in handy when dodging traffic. The lithium-ion battery provides enough juice to give the bike a range of up to 80 miles between recharges, making it a great option for daily commuters. Raleigh even outfitted the bike with wide tires which provide stability and traction, even when the road gets wet. Other key features include a 10-speed Shimano crankset and shifters and a built-in LCD screen that displays all the usual information.
The aluminum, step-through eJoy is the happy medium between traditional-looking townies that don’t transport much more than the rider and often cumbersome cargo models that are sometimes a challenge to store. With 26-inch wheels, full fenders, a Shimano Alivio nine-speed drivetrain and disc brakes, a wheelbase similar to the average townie, and a big, comfy seat, it has the appearance of a practical everyday cruiser. But its oversize rear rack, silent Bosch Active Line motor, heavy-duty head tube with front-tray mounts (the tray is an add-on), integrated Supernova E3 lights, and roll-over-anything balloon tires hurtle it into hmm-this-could-actually-replace-my-car status. It’s one of the quietest, most convenient, most stylish, and easiest-to-operate e-bikes available.

Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.

In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.

Speed Pedelec ebikes – A new classification of bikes called ‘Speed Pedelecs’ have emerged which technically meet the bicycle definition for a 20 mph ebike. These ebikes are designed to max out at 28 mph. Pedelecs are pedal activated vs throttle activated. The weasel words within the definition says, “20mph on motor alone”. Thus, a person who adds their leg power to the motor assist and happens to cruise at 28mph is NOT doing it by motor alone, and therefore the bike is considered to be compliant with the Federal Law. If the rider stops pedaling, the speed pedelec cannot maintain speed. Speed Pedelecs are becoming more popular in Europe and America, which means more models are being offered.
If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
Electric motorized bicycles can be power-on-demand, where the motor is activated by a handlebar mounted throttle, and/or a pedelec (from pedal electric), also known as electric assist, where the electric motor is regulated by pedaling. These have a sensor to detect the pedaling speed, the pedaling force, or both. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. Most controllers also provide for manual adjustment.
An electric bicycle is a bicycle with an electric motor used to power the vehicle, or to assist with pedaling. In many parts of the world, electric bicycles are classified as bicycles rather than motor vehicles, so they are not subject to the same laws as motor vehicles. Electric bicycles are one type of motorized bicycle. However, electric bicycles are defined separately and treated as a specific vehicle type in many areas of legal jurisdiction.
E-bikes mostly use motors and battery options from a few major suppliers: Bosch, Yamaha, Shimano, and Brose. A few other brands exist, but are less reliable or powerful. Some, like the Yamaha system, have more torque, and others, like Bosch’s Active Line, are nearly silent. But, generally, all four make good options. Look for motor output (in torque), which will give you an idea of total power. Just like car engines, more torque equals more power off the line and more boost to your pedaling. But watt hours (Wh) is perhaps a more important figure to use—it takes into account battery output and life to give a more accurate reflection of power (higher Wh equals bigger range).
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2 [123] as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
Haibike ships the HardNine with 29-inch tires, 180-millimeter hydraulic disc brakes, a 100-millimeter front suspension fork, and a nine-speed Shimano shifting system. The bike’s LCD readout is affixed to the handlebars and displays the current speed, level of charge, remaining range, and current pedal assist mode. The company says the battery can be completely recharged in just four hours, minimizing downtime between rides.