Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles,[77] including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity.[78] A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.[79]
Both the Stromer and the Stoeckli are very nice looking designs and easy to handle. Reliability for both does not seem to be up to Swiss standards, e.g. some of the 2012 Stöcklis seem to have bad contacts. However, as of 2013, most of these problems should be fixed. The Cube got criticized for its battery/saddle system, but this has probably been fixed in more recent edition and it has less "punch" then the other's since the motor is smaller (324W?). I don't know about the BH Neo Nitro. Given the relatively low price of the BH Nitro, it may be the best buy in this category if you plan to cover smaller distances (the battery is limited to 9Ah, and Spain's industry does need some help ;) Anyhow, all of these models come with a variety of motors and country-specific modifications. E.g. in France, the BH Nitro comes with a 350W motor and is electronically limited to 25km/h, whereas in Switzerland you either can get a 500W - 45 km/h version or a 250W? - 25km/h version.
There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.
The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.

Electric bikes are becoming a convenient and fun way to commute around a city, but they can be pricey. The average e-bike can cost $3,000, with some models getting up to $5,000 or more. But these prices are dropping, as new models come onto the market — and if you don’t mind giving up some of the glossier, high-tech features like embedded digital displays, retractable cable locks, and and theft tracking and recovery, you can find a really good quality e-bike for under $1,500.
As of 2008 a standard class C license, proof of insurance, and registration (annual fee: $9.00) are required for operation of any motorized pedalcycle in Pennsylvania. Additionally, there are strict equipment standards that must be met for operation, including: handlebars, brakes, tires/wheels, electrical systems/lighting, mirrors, speedometer, and horns/warning devices.[127]
This slick-looking commuter features a clean and quiet Gates Carbon Drive belt, which eliminates the maintenance that comes with a derailleur, and an internally geared Enviolo Trekking hub, which provides a 380 percent gear range. The Embark has 650b wheels, 47mm WTB gumwall tires, full fenders with mudflaps, and integrated lights—meaning you can ride long after the sun sets—or before it rises. A Bosch Active Line Plus mid-drive motor is light and quiet and provides pedal assist up to 20 mph, and the Bosch 400Wh battery has a claimed range of 50 miles. Everything about the Embark frame screams clean, stylish, and organic.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885.[7][8][9] However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
Electric Motorcycles News (EMN) has been launched in March 2017 and is a personal initiative from graphic designer Guy Salens (Belgium) to inform you about electric motorcycles, electric scooters and some offroad performance e-bikes. EMN collects and publishes all kind of info from available sources on the internet: press releases, existing website content from manufacturers. EMN has also developed a search engine where you can search for e-dealers with your specific keywords, in different countries, different brands and/or categories.
To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.
Equipped with a powerful motor, a portable Li-ion Battery, and all the other magic that goes into building a LightSpeed Electric Bicycle… It’s lighter than it looks, strong yet agile, and feels like flying.This beast is truly larger than life. To bring it home, you need a special invite. Follow this space for more information on how to get invited.

Rose Heyer and Josie Tabor of Dept Tech, Department of State Information Center, the Secretary of State and the office of ROCK AND BORGELT, P.C., Attorneys at Law, 24500 FORD ROAD, SUITE 10 DEARBORN HEIGHTS, MI 48127-3106, determined electric bicycles are considered mopeds and need registered and licensed. In order to operate an electric bicycle on public streets, the driver must have a valid operator, chauffeur, or special moped license. However, not all electric bicycles are street legal unless they have the following safety equipment: operating brake light, headlight, and turn signals. The local police department must inspect the bicycle using Form TR-54 which is taken with proof of purchase to the DMV. The fee for the plate is $15 for a three year decal, whereas the fine for no decal is $150 per incident.


Urban riding will never be the same, and cars will be in your way when you climb aboard the Specialized Turbo Vado 3.0. The zippy 28mph pedal-assist motor will leave you feeling invincible as you’re ripping along in turbo mode (which adds up to 320 percent of your power output). Although designed with female riders in mind—it comes with a women-specific saddle and grips, and a lower standover—the step-through frame is extremely convenient for anyone who doesn’t want to swing their leg over the back of a saddle while wearing street clothes. Slick, integrated lights, as well as fenders and a rear rack, add to the already-awesome features of this bike to make it the ideal combination of value, performance, and pep.
Visually, the Pedego City Commuter Classic Electric Bike is stunning – a smart blend of yesteryear's style and today's technology. Pleasantly high handlebars, a sprung seat, and lovely Schwalbe Fat Frank tires make it very comfortable. Stopping is taken care of by powerful disk brakes, front and rear. Lights are included, as is a useful cargo rack. From an e-bike standpoint, the Pedego Classic City Commuter sports a reliable, hub-mounted motor driven by a 36-volt, 10-amp battery. There's a digital display with a trip computer, odometer, speedometer, pedal assist level, and battery charge information.

First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead. 
I purchased version 2.0 of this device and the manufacturer has been listening to comments from users and making running changes such as the three speeds and the rear suspension. I am an XL size user (6'2", 230lbs) and recently returned from a 26 day cruise around Europe. I rode this little scooter on cobblestones, miles and miles through the Vatican, inside ancient cities and all over the streets of San Juan upon our return stateside. There was only one time it was less than ideal and that was going uphill, on slick tile that was wet from a drizzle. It still make it, just had to lean way forward to get weight on the front wheel.
Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[68]
Photo: Zap Electric's power-assist kit turns a conventional bike into an electric one. There's a bolt-on DC electric motor (weighing just over 3kg or 7lb) just above the back wheel, behind the police officer's foot, pressing against the tire and driving it by simple friction. The motor's powered by a compact lead-acid battery (weighing about 5.5 kg or 12 lb) inside a protective nylon bag. This kit adds quite bit of weight to the bike, but gives extra range and speed when needed. Photo taken in Santa Rosa, California by Rick Tang courtesy of US DOE/NREL.

Under the doctrine of One Country, Two Systems, Hong Kong has independent traffic law from mainland China. Electric bike are considered as motorcycles in Hong Kong, and therefore needs type approval from the Transport Department as other automobiles. All electric bike availble in Hong Kong fail to meet the type approval requirement, and Transport Department has never granted any type approval for electric bike, making all electric bike effectively illegal in Hong Kong. Even if they got type approved, the driver would need a motorcycle driving license to ride[14]. As a side note, Hong Kong doesn't have a moped vehicle class (and therefore moped driving license), and mopeds are consided as motorcycles too.
Toe-clips and toestraps and clipless pedals help keep the foot locked in the proper pedal position and enable cyclists to pull and push the pedals. Technical accessories include cyclocomputers for measuring speed, distance, heart rate, GPS data etc. Other accessories include lights, reflectors, mirrors, racks, trailers, bags, water bottles and cages, and bell.[52] Bicycle lights, reflectors, and helmets are required by law in some geographic regions depending on the legal code. It is more common to see bicycles with bottle generators, dynamos, lights, fenders, racks and bells in Europe. Bicyclists also have specialized form fitting and high visibility clothing.

You are not allowed to drive S-Pedelecs in France even if they are registered legally in your country (e.g. Germany or Switzerland). In other words, if you plan to take your 45h bike that is legal in your country on vacation in another where it is not, you may violate traffic law. Remove the license plate or don't do it. People who commute between countries, are known to hack removable plates with magnets ...
Mid-mounted system means that the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. Mid-drive systems tend to feel more like a normal bike, since they drive the pedals, just like your legs, and those who frequently climb long, steep hills tend to prefer mid-drive systems for their ability to handle long climbs. As they can leverage the bicycles lowest gears for climbs, mid drive systems can also leverage the high gears to reach higher speeds on flat areas than a hub system. The mid-drive motor drives the crank, instead of the wheel itself, which multiplies its power and allows it to better take advantage of the bike’s existing gears. If the rider changes the gears appropriately, the motor can turn closer to its ideal rotations per minute which makes a huge difference while climbing hills, so this is a perfect option for those who love mountain biking.
Arkansas does not define E-bikes. The following definition describes a combustion engine. E-bikes being electric do not have a cylinder capacity and thus this law is not technically applicable. The state defines a "Motorized bicycle" as "a bicycle with an automatic transmission and a motor of less than 50cc."[80] Riders require either a certificate to operate a motorized bicycle, a motorcycle license, a motor-driven cycle license, or a license of class A, B, C or D. Certificates cannot be issued to riders under 10 years of age.[81]
Toe-clips and toestraps and clipless pedals help keep the foot locked in the proper pedal position and enable cyclists to pull and push the pedals. Technical accessories include cyclocomputers for measuring speed, distance, heart rate, GPS data etc. Other accessories include lights, reflectors, mirrors, racks, trailers, bags, water bottles and cages, and bell.[52] Bicycle lights, reflectors, and helmets are required by law in some geographic regions depending on the legal code. It is more common to see bicycles with bottle generators, dynamos, lights, fenders, racks and bells in Europe. Bicyclists also have specialized form fitting and high visibility clothing.
A human traveling on a bicycle at low to medium speeds of around 16–24 km/h (10–15 mph) uses only the power required to walk. Air drag, which is proportional to the square of speed, requires dramatically higher power outputs as speeds increase. If the rider is sitting upright, the rider's body creates about 75% of the total drag of the bicycle/rider combination. Drag can be reduced by seating the rider in a more aerodynamically streamlined position. Drag can also be reduced by covering the bicycle with an aerodynamic fairing. The fastest recorded unpaced speed on a flat surface is 144.18 km/h (89.59 mph)[41]
"Electric-assisted bicycle" means a bicycle with two or three wheels, a saddle, fully operative pedals for human propulsion, and an electric motor. The electric-assisted bicycle's electric motor must have a power output of no more than one thousand watts, be incapable of propelling the device at a speed of more than twenty miles per hour on level ground, and be incapable of further increasing the speed of the device when human power alone is used to propel the device beyond twenty miles per hour.[66]
I like this little electric "scooter" a lot. I do think the rear wheels should be a bit further apart for added stability. I have also found it is too easy to "spin out" the front driver wheel when going up an incline or crossing a grass area. The user and assembly manual is minimal and could use considerably more information and more and better illustrations.
In general, electric bicycles are considered "bicycles", rather than motor vehicles, for purposes of the code. This implies that all bicycle regulations apply to electric bicycles including operation in bike lanes. Exceptions to this include a restriction of operation on sidewalks and that a license or permit is required if the rider is younger than 17 years of age.[125]
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.
But if you're someone who loves riding, commutes to work on a bike, or has a gig that requires you to spend a lot of time in the saddle, you might want to look at electric bikes. You'll be able to go farther, faster, and expend less energy riding one. And if electric bikes are for you, look hard at the Cross E8 Step-Thru. It's an incredibly well-made, well-thought-out electric bike. Strip away the battery, motor, and computer, and you'd still be left with a really good cycle.
(ii) a vehicle equipped with two or three wheels, foot pedals to permit muscular propulsion, and an independent power source providing a maximum of 2 brake horsepower. If a combustion engine is used, the maximum piston or rotor displacement may not exceed 3.05 cubic inches, 50 centimeters, regardless of the number of chambers in the power source. The power source may not be capable of propelling the device, unassisted, at a speed exceeding 30 miles an hour, 48.28 kilometers an hour, on a level surface. The device must be equipped with a power drive system that functions directly or automatically only and does not require clutching or shifting by the operator after the drive system is engaged.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
An itinerant wordsmith with a broad constellation of interests, Lydia Chipman has turned iconoclasm into a livelihood of sorts. Bearing the scars and stripes of an uncommon diversity of experience -- with the notable exceptions of joining a religious order or becoming an artist -- she still can’t resist the temptation to learn something new. Lydia holds a master of arts in English from Georgia Southern University, and a bachelor of arts cum laude in integrative studies from Clayton College. Her expertise is in the areas of robotics, electronics, toys, and outdoors and computer equipment.
Generally they are considered vehicles (like motorcycles and pedal cycles), so are subject to the same rules of the road. Regulations may define maximum power output and for electric bikes may or may not require an interlock to prevent use of power when the rider is not pedaling. In some cases regulatory requirements have been complicated by lobbying in respect of the Segway HT.
In Israel, persons above 16 years old are allowed to use pedal-assisted bicycle with power of up to 250W and speed limit of 25 km/hour. The bicycle must satisfy the European Standard EN15194 and be approved by the Standards Institution of Israel. A new law, effective January 10, 2019, states that riders under 18 who have no automobile license will need a special permit. [51] [52] Otherwise, no license or insurance is required. Other motorized bicycles are considered to be motorcycles and should be licensed and insured as such.[53] The maximum weight of the e-bike itself cannot exceed 30 kg.[54]
Even with cheaper or heavier bikes, once you accept that you are really meant to pedal gently and let the motor do the work, non-speed freaks will get into it. E-bikes are great for commuting and for places that aren't pancake flat. They'll pull you away from the lights quickly, iron out hills and stop you getting sweaty, so you can bin the Lycra and ride in jeans, a suit, or a winter coat.
There are specialized bicycle tools for use both in the shop and on the road. Many cyclists carry tool kits. These may include a tire patch kit (which, in turn, may contain any combination of a hand pump or CO2 Pump, tire levers, spare tubes, self-adhesive patches, or tube-patching material, an adhesive, a piece of sandpaper or a metal grater (for roughing the tube surface to be patched), Special, thin wrenches are often required for maintaining various screw fastened parts, specifically, the frequently lubricated ball-bearing "cones".[57][58] and sometimes even a block of French chalk.), wrenches, hex keys, screwdrivers, and a chain tool. There are also cycling specific multi-tools that combine many of these implements into a single compact device. More specialized bicycle components may require more complex tools, including proprietary tools specific for a given manufacturer.
The other motor is the G311, a front equivalent to the wonderfully silent G310 rear motors we introduced late last year. This motor will be replacing the G01 hub for our front mini geared kits. It's a tad lighter (2.3kg), much quieter (spiral gears!), but still has the features from the G01 that we loved. That means a side cable exit, ISO disk rotor compatibility, and 10mm round axle.
Simple, convenient, cheap, and economical—bicycles are one of the world's favorite forms of transportation. But they're not for everyone. They can be hard to pedal up and down hills or with heavy loads, and elderly or disabled people may find them impossible to manage. In the last few years, a new generation of electric bicycles has begun to revolutionize our idea of environmentally friendly transportation. These new cycles have all the convenience of cars with all the simple economy of ordinary cycles. Let's take a closer look at how they work. 
×