State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.
Simple, convenient, cheap, and economical—bicycles are one of the world's favorite forms of transportation. But they're not for everyone. They can be hard to pedal up and down hills or with heavy loads, and elderly or disabled people may find them impossible to manage. In the last few years, a new generation of electric bicycles has begun to revolutionize our idea of environmentally friendly transportation. These new cycles have all the convenience of cars with all the simple economy of ordinary cycles. Let's take a closer look at how they work.
All classes of electric-assisted bicycles may be operated on a fully controlled limited access highway. Class 1 and 2 electric bicycles can be used on sidewalks, but Class 3 bicycles "may not be used on a sidewalk unless there is no alternative to travel over a sidewalk as part of a bicycle or pedestrian path." Generally a person may not operate an electric-assisted bicycle on a trail that is designated as non-motorized and that has a natural surface, unless otherwise authorized.
Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.
You can learn more about the development and axle testing process on this endless-sphere thread. Our ambition is to make this splined axle design into a new standard that we deploy across our entire higher power motor lines to replace axle flats. If you're as excited as us and want to jump right into ordering, we have the first production shipment on hand available in bare motors and complete kits.
Bicycle brakes may be rim brakes, in which friction pads are compressed against the wheel rims; hub brakes, where the mechanism is contained within the wheel hub, or disc brakes, where pads act on a rotor attached to the hub. Most road bicycles use rim brakes, but some use disk brakes. Disc brakes are more common for mountain bikes, tandems and recumbent bicycles than on other types of bicycles, due to their increased power, coupled with an increased weight and complexity.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885. However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
The Netherlands has a fleet of 18 million bicycles. E-bikes have reached a market share of 10% by 2009, as e-bikes sales quadrupled from 40,000 units to 153,000 between 2006 and 2009, and the electric-powered models represented 25% of the total bicycle sales revenue in that year. By early 2010 one in every eight bicycles sold in the country is electric-powered despite the fact that on average an e-bike is three times more expensive than a regular bicycle.
Electric-assist and other "motorized bicycles" do not need to be inspected, do not require a license, and do not require registration. The vehicle must meet all of the following criteria: a post mounted seat for each person it is designed to carry, two or three wheels which contact the ground, fully operative pedals, wheels at least 16 inches in diameter and a motor not capable of propelling the device at more than 20 mph on level ground. The driver does not need a license, but must be at least 16 years old. DC law prohibits motorized bicycles from traveling anywhere on the sidewalk or in the bike lanes. DC Regulation 18-1201.18 provides: "Except as otherwise permitted for a motor vehicle, no person shall operate a motorized bicycle on any sidewalk or any off-street bikepath or bicycle route within the District. This prohibition shall apply even though the motorized bicycle is being operated solely by human power." So, if cars are prohibited in a particular place, motor-assisted bikes are also prohibited.
Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.
"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Chapter 551., titled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D. The following definition of electric bicycle was passed by the Texas legislature in 2001. "Electric bicycle" means a bicycle that is designed to be propelled by an electric motor, exclusively or in combination with the application of human power, cannot attain a speed of more than 20 miles per hour without the application of human power; and does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle on a highway that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle on a highway used primarily by pedestrians.
Flyer Vollblut. A new rear motor bike from one of the most reliable E-bike makers. This model doesn't look as "heavy" as most other Flyer models. The Vollblut 500 has the 500W new Panasonic rear motor, front fork suspension, 28 inch wheels. It is in the same price range as the Stöckli and the Stromer. Flyer is known for top service and reliability, but it's a new model with a new motor ....
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers. If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.
Electric motor assisted bicycles have been banned in the State of New York and are not permitted for on-road use. It appears the only known allowance of an electric bicycle is if it is an electric powered moped, at this time. There is a proposed bill to allow ebikes. As of May 2009, Bill A2393("Defines the term electric assisted bicycle") has been passed in the NY State Assembly and its corresponding Bill S4014, sponsored by Senator Thomas Morahan, is before the NY State Senate.
Artwork: Hub motors aren't the only way to power electric bicycle wheels. If you've ever watched a mouse scampering around inside an exercise wheel, you might have wondered if you could drive a wheel electrically, in a similar way, with something that pushes against the inside of the rim. A company called GeoOrbital has been developing an ingenious mechanical equivalent that can be used to power conventional bikes—and here's a simplified illustration of how it works. It has a motorized drive roller (red) that presses against the inner rim, powered by a battery pack (orange) that sits snugly inside the wheel. Two guide rollers (blue) mounted on a tensioned framework (green) take the place of the conventional arrangement of spokes. According to GeoOrbital, you can fit one of its wheels to a normal bike in just 60 seconds.
The batteries are the most important parts of the bike, because (if you don't do any pedaling) they contain all the power that will drive you along. Typical electric bike batteries make about 350–500 W of power (that's about 35–50 volts and 10 amps), which is about a quarter as much as you need to drive an electric toaster. In theory, you could use any kind of battery on a bicycle. In practice, however, you want to use something that stores lots of power without being too heavy—or you'll be using half your power just moving the battery along! That tends to rule out heavy lead-acid batteries like the ones that start cars, though some electric bikes do use them. Lightweight lithium-ion batteries, similar to those used in laptop computers, mobile (cellular) phones, and MP3 players, are now the most popular choice, though they're more expensive than older rechargeable battery technologies such as nickel-cadmium ("nicad"). Typical batteries will give your bicycle a range of 10–40 miles between charges (depending on the terrain) and a top speed of 10–20 mph (which is about the maximum most countries allow for these vehicles by law). You can extend the range by pedaling or free-wheeling some of the time.
As the managing editor of Ars Technica, one of my duties is to monitor the daily torrent of news tips and PR emails. The overwhelming majority of them is deleted after a glance, and the news tips and story ideas are passed along to the appropriate writer. Sometimes a product announcement will catch my eye, and I will follow up. Once in a blue moon, I'll say, "please send me one so that I may review it." And that's how I ended up riding an electric bike around the Chicago suburbs for two weeks.
An electric bicycle also known as an e-bike is a bicycle with an integrated electric motor which can be used for propulsion. Many kinds of e-bikes are available worldwide, from e-bikes that only have a small motor to assist the rider's pedal-power (i.e., (pedelecs) to somewhat more powerful e-bikes which tend closer to moped-style functionality: all, however, retain the ability to be pedalled by the rider and are therefore not electric motorcycles.
In general, U.S. and European cycle manufacturers used to assemble cycles from their own frames and components made by other companies, although very large companies (such as Raleigh) used to make almost every part of a bicycle (including bottom brackets, axles, etc.) In recent years, those bicycle makers have greatly changed their methods of production. Now, almost none of them produce their own frames.
If you're more concerned with conquering the countryside than the commute, Cyclotricity's Stealth is the one for you. It's a full-size mountain bike, with aggressive tyres and suspension on the front forks to absorb the rocks and bumps on the trails. It's comfortable to ride, and its motor can either give you assistance while you ride, or you can just hit the throttle to rocket over hills with no effort on your part.
It’s unlikely the Instagram generation ever thought there would be an eBike built with them in mind. Stereotypes of old people riding their e-assisted bikes with cumbersome batteries and questionable frames. Then Lithium Cycles and the Super 73 turned up! Across the last few months, social media has been bustling with talk, influencers, Will Smith … Continue reading Lithium Cycles Super 73: Coming Soon
This was the first ebike I ever bought. I've since become a builder and make my own. But this was a really reliable vehicle. I used it everyday for transportation. The company sent me any part I needed. It's got a power motor on it so it's super reliable. I wouldn't hesitate to buy this bike especially if you're new into the ebike world. If your looking to have some real fun buy this bike.. If your looking to meet new people buy this bike. If looking to go more green buy this bike. This bike is so much fun you well want to ride all day. This bike should be twice the price . I love love love it .
With a 150mm-travel RockShox Yari fork and 132mm of rear travel from the RockShox Monarch Plus R shock, the Remote CTRL is Kona’s first dual-suspension e-mountain bike. It’s powered by a 250-watt Bosch Performance Line XC mid-drive motor that uses the company’s progressive E-MTB mode that is adaptable to rider input, which means you don’t have to toggle through assistance modes while riding. It offers assistance up to 20 mph, and the 500Wh integrated battery is the largest Bosch currently offers. Beefy 27.5x2.8-inch Maxxis Recon tires offer plenty of traction and also help to absorb smaller hits.
At the moment this battery is in stock but for local pickup orders only as we are going through the certification testing required for shipping. We've been keeping the 21700 cell offerings on our radar as they start to catch up with the performance specs of the more mature 18650 series and this year it looks like they are finally making the grade. Expect more from us as the year goes on.
After you decide which style of e-bike you want, consider the class. In the U.S., there are three classes defined by the type of assist and how fast the motor will propel you. Most electric bikes sold are class 1 or 3. Class 1 bikes have a motor (max 750w) that assists while you’re pedaling, up to 20 mph. Class 3, also known as “speed pedelec,” can also have up to a 750w motor, but it can assist you up to 28 mph. Both are allowed in most states and cities without requiring a license. Class 2 models have throttles that don’t require the rider to pedal in order to get a boost. They’re allowed on most streets, bike lanes, and paths, but are less popular than the other classes and not covered much here (because not only do we still love to pedal, we also prefer the greater distances that pedal-assist bikes can cover).
Built around a heavy-duty alloy frame, the GSD eschews many of the traits of other cargo bikes: long wheelbases, bigger wheels, and especially, an unwieldy ride. Yet it boasts an extensive capacity, nimble handling—even fully loaded, thanks to a short wheelbase and 20-inch wheels—and enduring range in a package not much bigger than most non-cargo e-bikes. The stout frame holds a 250-watt Bosch motor that gives up to 275 percent of your power back to the pedals and reaches 20 mph. The GSD has room for two battery packs, extending the batteries’ combined range to a claimed 150 miles and making the Tern one of the longest-lasting e-bikes on the market. A laundry list of accessories and a (claimed) 396-pound carrying capacity round out the GSD’s status as an epic day-tripper.
Electric trikes have also been produced that conform to the e-bike legislation. These have the benefit of additional low speed stability and are often favored by people with disabilities. Cargo carrying tricycles are also gaining acceptance, with a small but growing number of couriers using them for package deliveries in city centres. Latest designs of these trikes resemble a cross-between a pedal cycle and a small van.
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
Haibike ships the HardNine with 29-inch tires, 180-millimeter hydraulic disc brakes, a 100-millimeter front suspension fork, and a nine-speed Shimano shifting system. The bike’s LCD readout is affixed to the handlebars and displays the current speed, level of charge, remaining range, and current pedal assist mode. The company says the battery can be completely recharged in just four hours, minimizing downtime between rides.