Maryland defines an "electric bicycle" as a vehicle that (1) is designed to be operated by human power with the assistance of an electric motor, (2) is equipped with fully operable pedals, (3) has two or three wheels, (4) has a motor with a rating of 500 watts or less, (5) and is capable of a maximum speed of 20 miles per hour on a level surface when powered by the motor. (Senate Bill 379, approved by the Governor 5/5/2014, Chapter 294.) [96] This legislation excludes "electric bicycle" from the definition of "moped", "motorized minibike", and "motor vehicle", and removes the titling and insurance requirements required for electric bicycles under prior Maryland law.


A local unit of government having jurisdiction over a road or bikeway (including the Department of Natural Resources in the case of state bike trails) is authorized to restrict e-bike use if: the use is not consistent with the safety or general welfare of others; or the restriction is necessary to meet the terms of any legal agreements concerning the land on which a bikeway has been established.
Some of the Rad Wagon’s (small) flaws became apparent once I added more weight to the bike. The integrated rear rack can attach various panniers, platforms, or baskets to cary your cargo, but I was most concerned with hauling my two kiddos to school. Riding the bike with my three year old was a cinch; he held on to the bars in the caboose (available as an accessory add-on) and enjoyed the view. Adding my very tall, almost seven-year-old daughter, however, was a bit more complicated.
The frame of a fat e-bike resembles that of a traditional bike, with front and rear portions that are a bit wider to accommodate the large tires. Your height and weight will dictate which frame size suits you best. You’ll want to go through the process of mounting and dismounting the bike to make sure you’re comfortable climbing on and off before you commit to it.
Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.

Even the humble bicycle hasn't escaped the clutches of modern technology. A whole herd of new e-bikes with electric motors are taking to our cities' streets. Adding a motor to a standard cycle does ramp up the price significantly, but it takes much of the effort out of cycling, making your commute to the office a sweat-free experience and allowing you to sit back and enjoy your suburban cruise.

Electric bicycles are not allowed in any public area, meaning an area where there is full or partial public access. Any kind of pedal assist, electric bike, scooter, moped or vehicle which has any form of propulsion, whether in full or as assist, other than human power, must be approved as either a car, motorcycle, van, truck, bus or similar. This makes pedelecs and tilt-controlled two-wheel personal vehicles illegal in all practical ways, as they cannot be registered as a motor cycle.[36]


To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
Every person riding a bicycle, electric personal assistive mobility device, electric power-assisted bicycle, moped, or an animal or driving an animal on a highway shall be subject to the provisions of this chapter and shall have all of the rights and duties applicable to the driver of a vehicle, unless the context of the provision clearly indicates otherwise.
Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.

The frame of an electric bike also has to be slightly different. The main part of the frame (the bit that supports your weight) is usually made from lightweight aluminum alloy: the lighter the frame, the lighter the weight of the bike overall, and the further it can travel before you need to recharge the batteries. The spokes on the wheel also have to be stronger than the thin spokes on a traditional bicycle. That's because the electric motor in the hub spins the wheel with a lot of turning force (known as torque) and, if the spokes were ordinary lightweight ones, they could bend or buckle.
Battery – in combination with the motor, this determines how far you can get before your bike needs a recharge. Some don’t provide adequate support on even gentle hills, while the best will comfortably take the strain as the gradient shoots up. Range also varies, with the best e-bike systems we’ve tested able to take you nearly twice the distance of lesser models.
My one complaint is the bike’s weight. This sucker is heavy! The aluminum frame looks light, but the the hub motor (4 pounds) and battery (5 pounds) add up. The bike’s total weight is 39 pounds, which is about average for e-bikes but not something you’d want to lug around all day. “This is not a solution for everybody,” Miller admits. “If you live in a fifth floor walkup this is probably not going to work.”
The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.
One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170-pound rider when powered only by that engine.[106]
Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
Most electric bicycles can be locked using keys supplied by the manufacturer. The key is usually inserted into a switch, which is commonly found on the bicycle's handlebars or on one side of the motor compartment. When switched to the "Off" position, the electrical drive system cannot be turned on. In areas of high risk for bicycle theft, these locking mechanisms are used in conjunction with coil or U locks.
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.
Since cyclists' legs are most efficient over a narrow range of pedaling speeds, or cadence, a variable gear ratio helps a cyclist to maintain an optimum pedalling speed while covering varied terrain. Some, mainly utility, bicycles use hub gears with between 3 and 14 ratios, but most use the generally more efficient dérailleur system, by which the chain is moved between different cogs called chainrings and sprockets in order to select a ratio. A dérailleur system normally has two dérailleurs, or mechs, one at the front to select the chainring and another at the back to select the sprocket. Most bikes have two or three chainrings, and from 5 to 11 sprockets on the back, with the number of theoretical gears calculated by multiplying front by back. In reality, many gears overlap or require the chain to run diagonally, so the number of usable gears is fewer.

Over the last few years, I’ve taken my love of the outdoors, hiking, skiing, trekking and exploring to the next level by starting this site. I started a bike shop in Denver, CO, and have seen amazing growth over the last few years. Getting paid to do what I love has been a dream come true for me. That’s also what led me to start BikesReviewed.com. In my shop, I spend a large amount of time helping people find the perfect bike for them and the style of biking they’re going to be doing. It only made sense that I expanded my reach and got online, making it possible for me to help people all over the world. If biking and staying fit is your priority, too, you’ve come to the right place.


The environmental effects involved in recharging the batteries can of course be reduced. The small size of the battery pack on an e-bike, relative to the larger pack used in an electric car, makes them very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots", in which e-bike riders can charge their vehicles while parked under photovoltaic panels.[66]

As electric bike options continue to expand, more brands are integrating the battery more seamlessly. That makes them look sleeker (and more like a real bike). Batteries are expensive, so make sure there’s a good way to lock the battery to your bike if you’ll be keeping it outside. Overall weight is important. Some battery and motors can add 15 pounds or more to the bike. With assist, you won’t feel that much when you’re riding, but you will if you have to carry your bike up stairs or lift it onto a bike rack.
I would advocate you ride legal within the laws of your state. I would also look into some kind of liability rider or umbrella policy with your home owner’s policy, which covers your personal liability and theft. Get your bike registered; wear your helmet, eye protection, whatever is required by state law so that if an accident occurs and you are at fault, there is no legal recourse. Even if you own a 750W/20mph ebike that meets the definition of a bicycle, any at-fault cyclist may still be denied coverage by stingy insurance companies who want to support their clients. Your health insurance will usually cover your medical bills, but the costs of an expensive ebike may be lost.
Bicycle manufacturing proved to be a training ground for other industries and led to the development of advanced metalworking techniques, both for the frames themselves and for special components such as ball bearings, washers, and sprockets. These techniques later enabled skilled metalworkers and mechanics to develop the components used in early automobiles and aircraft.
In Israel, persons above 16 years old are allowed to use pedal-assisted bicycle with power of up to 250W and speed limit of 25 km/hour. The bicycle must satisfy the European Standard EN15194 and be approved by the Standards Institution of Israel. A new law, effective January 10, 2019, states that riders under 18 who have no automobile license will need a special permit. [51] [52] Otherwise, no license or insurance is required. Other motorized bicycles are considered to be motorcycles and should be licensed and insured as such.[53] The maximum weight of the e-bike itself cannot exceed 30 kg.[54]
In my research about ebikes and the law, I cannot begin to justify how often articles about the laws evolved into the various ways and techniques to sneak around public notice and be stealth with the your ebike. The goal is to ride fast and fun, stay away from public awareness, and ‘Fly under the Radar’. I have been there and I get the drift. Sales and production are up. Electric bike kits, DIY enthusiast, long distance commuters, and a general drive for value is raising the desire for more options for consumers, wanting speed for fun and function, while developing amnesia for the law. People want to ride their new ebikes, and have the same access to safe pathways as they did the week before on their 100% human bike. Rather than deal with the inevitable conflicts over access, behavior and perception within the general public, the typical user will try to blend in with the normal cycling community.
Every person riding a bicycle, electric personal assistive mobility device, electric power-assisted bicycle, moped, or an animal or driving an animal on a highway shall be subject to the provisions of this chapter and shall have all of the rights and duties applicable to the driver of a vehicle, unless the context of the provision clearly indicates otherwise.
80% of your personal Carbon Footprint is made up of three main things. How you POWER your House. What you EAT. How you TRANSPORT yourself. There are major changes happening in all three of these areas. In the next 5-10 years, homes will have economical options to incorporate Power Generation, Power Storage and putting Surplus Power back on the Grid. …

But the whole is also influenced by the sensory systems which are very different from model to model. E.g. A typical 2013 Panasonic system requires pedalling for optimal support (55/minute?) and has both a pedalling frequency and a speed sensor. You don't get much assistance if you pedal very slowly or very fast. Typically, a rear motor has a force sensor, i.e. you get lots of support fast when you start pedalling in a low gear, i.e. it will "feel" your need for assistance.


The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
There are two basic categories of electric bike, and their uses don't offer equal crossover value. The first category is essentially a normal bicycle that has been outfitted with an electric motor. These bikes are the same size as a standard bicycle, and handle almost identically, save for the obvious benefit of added motive power thanks to a motor and battery.

The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].
Perhaps the cleverest thing of all about the Electric Brompton is that despite all the extra stuff, it folds up exactly the same as the non-powered variety. It's so simple, and unlike certain folding bikes we could mention, what you're left with is a genuinely small thing, rather than something that's about the size of a bike with the front wheel taken off.
×