To be honest, this bike is really designed for city commuters or kids riding around the suburbs. The fact that it’s foldable will let you carry it on the bus, on the train or even on the plane. It’s just not designed for heavy riding, long distances or tough terrains. If you want something sleek and fabulous at a fraction of the cost of most other e-bikes, this baby’s for you.

Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.[5]
Another style is the recumbent bicycle. These are inherently more aerodynamic than upright versions, as the rider may lean back onto a support and operate pedals that are on about the same level as the seat. The world's fastest bicycle is a recumbent bicycle but this type was banned from competition in 1934 by the Union Cycliste Internationale.[43]
But if you're someone who loves riding, commutes to work on a bike, or has a gig that requires you to spend a lot of time in the saddle, you might want to look at electric bikes. You'll be able to go farther, faster, and expend less energy riding one. And if electric bikes are for you, look hard at the Cross E8 Step-Thru. It's an incredibly well-made, well-thought-out electric bike. Strip away the battery, motor, and computer, and you'd still be left with a really good cycle.
Play it Safe, Make it Easy – E-bike manufacturers will offer you a large variety of styles, types, colors and utility, but the base specifications will be a bike producing less than 750 watts of power (1 horsepower = 746W) , and have its speed limited to 20mph on motor power alone. The majority of US ebikes meet that specification. Manufacturers do this for their own liability. Going this route assures you that your bike was built and sold legally. As a result, you will have about every privilege that a normal bicycle can expect. However, state and local laws may dictate reduced speeds and limited access to bike paths.
State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.
Flyer Vollblut. A new rear motor bike from one of the most reliable E-bike makers. This model doesn't look as "heavy" as most other Flyer models. The Vollblut 500 has the 500W new Panasonic rear motor, front fork suspension, 28 inch wheels. It is in the same price range as the Stöckli and the Stromer. Flyer is known for top service and reliability, but it's a new model with a new motor ....

Under Title 23, Chapter 316 of the code, bicycles and motorized bicycles are defined as follows: Bicycle—Every vehicle propelled solely by human power, and every motorized bicycle propelled by a combination of human power and an electric helper motor capable of propelling the vehicle at a speed of not more than 20 miles per hour on level ground upon which any person may ride, having two tandem wheels, and including any device generally recognized as a bicycle though equipped with two front or two rear wheels. The term does not include such a vehicle with a seat height of no more than 25 inches from the ground when the seat is adjusted to its highest position or a scooter or similar device. No person under the age of 16 may operate or ride upon a motorized bicycle. Motorized Scooter—Any vehicle not having a seat or saddle for the use of the rider, designed to travel on not more than three wheels, and not capable of propelling the vehicle at a speed greater than 30 miles per hour on level ground.[90]


Bicycles can be categorized in many different ways: by function, by number of riders, by general construction, by gearing or by means of propulsion. The more common types include utility bicycles, mountain bicycles, racing bicycles, touring bicycles, hybrid bicycles, cruiser bicycles, and BMX bikes. Less common are tandems, low riders, tall bikes, fixed gear, folding models, amphibious bicycles, cargo bikes, recumbents and electric bicycles.
Perhaps the cleverest thing of all about the Electric Brompton is that despite all the extra stuff, it folds up exactly the same as the non-powered variety. It's so simple, and unlike certain folding bikes we could mention, what you're left with is a genuinely small thing, rather than something that's about the size of a bike with the front wheel taken off.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].
There is a lot of information on the internet about electric bikes. Hopefully you have found lots of useful information right here, on this website. Based on this information, you may already have a preference for a specific electric bicycle and / or (technical) components. Your friends that ride e-bikes can also advise you based on their own experiences. But there is only one way you will know if you really make the right choice: take a test drive. During a test drive you will discover how close the riding experience is to your expectations.

Electric motor assisted bicycles have been banned in the State of New York and are not permitted for on-road use.[50][51] It appears the only known allowance of an electric bicycle is if it is an electric powered moped, at this time. There is a proposed bill to allow ebikes. As of May 2009, Bill A2393("Defines the term electric assisted bicycle") has been passed in the NY State Assembly[52] and its corresponding Bill S4014, sponsored by Senator Thomas Morahan, is before the NY State Senate.[53]

With a chain drive transmission, a chainring attached to a crank drives the chain, which in turn rotates the rear wheel via the rear sprocket(s) (cassette or freewheel). There are four gearing options: two-speed hub gear integrated with chain ring, up to 3 chain rings, up to 11 sprockets, hub gear built into rear wheel (3-speed to 14-speed). The most common options are either a rear hub or multiple chain rings combined with multiple sprockets (other combinations of options are possible but less common).


I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have
Did you know that electric bikes can be used for fitness training? Or that they have been scientifically proven to increase the amount of cycling people do? Or that they have proven health and fitness benefits? Well, it’s all true! Apart from being tons of fun, ebikes can be used to improve health and fitness in many ways. Here are our top posts about how ebikes can improve your health and fitness.
Electric bikes are a green alternative to driving a vehicle. Studies carried out in several towns and cities show that the average car speed in rush hour traffic can dip as low as 18 to 20 mph. Electric bike speed can be as high as 15 mph. With an electric bike, you can reduce pollution, improve fitness, and still arrive at the same time as your car-bound colleagues.
About Terry Brightwater. Terry lives in the Afan Forest, South Wales, UK, with his wife Jay Brightwater. He is a professional Life Coach, specialising in “Emotional Fitness” for over 18 years. Terry’s passion for health and fitness, has spanned over the last 40 years, mainly being expressed through cycling, weight training and healthy eating. He … Continue reading eBikes as a Wonderful Health and Fitness Tool by Terry Brightwater
Whether squeezing onto the 4 train or pedaling through Lower Manhattan, I notice a few curious glances at the bike with the big battery in the center of the frame. This is not surprising; e-bikes are huge practically everywhere but the US. According to the latest figures from the Confederation of the European Bicycle Industry, e-bike growth in the UK is up from 40,000 units in 2016 to 63,000 in 2017.
Last year we found a very low-priced (under $600 at Amazon) bike made by Ancheer. Overall, it made some good compromises to get down to the $600 price point but I had some issues with the build quality, the power of the motor, lack of display on the controller and size of the battery. This year a new low-cost Amazon ebike from Rattan seems to have answered many of my concerns.
The Espin is powered by a 350-watt motor that’s rated for trips up to 50 miles (depending on the terrain and assist level). Once depleted, the battery fully charges in roughly five hours. Thankfully, Espin makes it easy to remove the battery, allowing you to quickly recharge it at home or in the office between trips. A backlit LCD control hub displays your basic metrics and battery life while in transit and LED headlights add a touch of light when needed.
To qualify as an electric-assisted bicycle under state law they need to have a seat and fully operable pedals for human propulsion, meet federal motor vehicle safety standards, an electric motor that has a power output of not more than 1,000 watts, maximum speed of not more than 20 mph (electric motor and human power combined), disengages or ceases to function when the vehicle’s brakes are applied, two or three wheels
In a friction drive motor, a small, solid wheel rotates against the side of the tire in order to drive it. The first motorcycles used the same concept, with a motor mounted above the front wheel. The problem is that the drive rubs at the side of the tire. It's inefficient, and it quickly wears the sidewall away. Tires need to be replaced every couple hundred miles. For this reason, you'll seldom see electric bikes with this type of drive anymore.
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[94][95] Helmets are required.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]

In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.
Bicycles were introduced in the late 19th century in Europe, and by the early 21st century, more than 1 billion were in existence at a given time.[1][2][3] These numbers far exceed the number of cars, both in total and ranked by the number of individual models produced.[4][5][6] They are the principal means of transportation in many regions. They also provide a popular form of recreation, and have been adapted for use as children's toys, general fitness, military and police applications, courier services, bicycle racing and bicycle stunts.
Riding position: You also may wish to check out an e-bike’s riding position before investing in it. For short trips, the riding position might not make much difference, but for long journeys, the upright "Dutch" style with pulled-back handlebars is very comfortable – particularly for tall riders. The same goes for mountain bike styles, though these bikes are not often designed to actually go off-road.
Battery-electric locomotive Battery electric vehicle Cater MetroTrolley Electric aircraft Electric bicycle Pedelec Electric boat Electric bus Battery electric bus Electric car List Electric truck Electric platform truck Electric vehicle Electric motorcycles and scooters Electric kick scooter Gyro flywheel locomotive Hybrid electric vehicle Hybrid train Motorized bicycle Neighborhood Electric Vehicle Plug-in electric vehicle List Plug-in hybrid electric vehicle Solar vehicle Solar car Solar bus

Stöckli E.T. Urban Confort, made in Switzerland. It has SwissGoDrive motors and Samsung batteries. There is a 500W/17.6Ah combo that seems to be ideal for commuters, i.e. it has a 50km range using full assistance. In the USA, a similar product is available as Currie eFlow e3 Nitro (different motor and electronics). This model doesn't have a front wheel suspension, but comes with "balloon" tires that somewhat absorb shocks. Options are available through types: "simple"/Urban/CROSS and man/confort models. E.g. the Cross model has a front suspension, a 500W motor and no equipment like lights, fenders, etc. However, paying extra, you can compose your own configuration. If you commute using bumpy roads, then get a front suspension.

Electric Bicycles are defined by the California Vehicle Code [32][33]. In summary, electric bicycles are to be operated like conventional bicycles in California. There are several exceptions to this. A person must be at least 16 years old, and anyone riding an electric bicycle must wear a bicycle helmet. The e-bikes must have an electric motor that has a power output less than 1,000 watts, is incapable of propelling the device at a speed of more than 20 miles per hour on level ground, is incapable of further increasing the speed of the device when human power is used to propel the motorized bicycle faster than 20 miles per hour, operates in a manner so that the electric motor is disengaged or ceases to function when the brakes are applied, or operates in a manner such that the motor is engaged through a switch or mechanism that, when released, will cause the electric motor to disengage or cease to function.

Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]


Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.
Ride1Up 500 series City is a high quality, classy and stylish electric city bike with great features at a really great price. It is designed for the everyday long-distance rider and it features very nice frame geometry that promotes a comfortable upright riding position. Swept-back cafe style handlebars also provide better comfort over longer distances. You can choose between two throttle options – a twist or a thumb throttle, and there are also 3 levels of pedal-assist, or 9 levels if you get an optional LCD screen. Other features include an integrated LED headlight, removable battery with two keys, and heavy duty kickstand. Also we have to commend the amazing customer service, as the guys that are behind this brand are very passionate about what they do, and really motivated to change the way we get around our communities, by providing high-quality bikes at an unbeatable price.
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.[23][24][25]
Even with cheaper or heavier bikes, once you accept that you are really meant to pedal gently and let the motor do the work, non-speed freaks will get into it. E-bikes are great for commuting and for places that aren't pancake flat. They'll pull you away from the lights quickly, iron out hills and stop you getting sweaty, so you can bin the Lycra and ride in jeans, a suit, or a winter coat. 

Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2 [123] as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.

Would an e-bike that used a trailing generator to power the electric motor still be considered an e-bike? The purpose of the generator is allow greater distances to be traveled and all day riding. The gen-set that I am looking at uses a 49 cc gas engine with a 12 volt generator, this would be from the ground up build using a 1 hp electric motor. This seems to stay within the state laws of AZ. where I reside. Thanks for your thoughts.
An electric bicycle is a bicycle with an electric motor used to power the vehicle, or to assist with pedaling. In many parts of the world, electric bicycles are classified as bicycles rather than motor vehicles, so they are not subject to the same laws as motor vehicles. Electric bicycles are one type of motorized bicycle. However, electric bicycles are defined separately and treated as a specific vehicle type in many areas of legal jurisdiction.
More powerful pedelecs which are not legally classed as bicycles are dubbed S-Pedelecs (short for Schnell-Pedelecs, i.e. Speedy-Pedelecs) in Germany. These have a motor more powerful than 250 watts and less limited, or unlimited, pedal-assist, i.e. the motor does not stop assisting the rider once 25 km/h has been reached. S-Pedelec class e-bikes are therefore usually classified as mopeds or motorcycles rather than as bicycles and therefore may (depending on the jurisdiction) need to be registered and insured, the rider may need some sort of driver's license (either car or motorcycle) and motorcycle helmets may have to be worn.[14] In the United States, many states have adopted S-Pedelecs into the Class 3 category. Class 3 ebikes are limited to <=750 watts of power and 28 mph.[15]

Photo: Zap Electric's power-assist kit turns a conventional bike into an electric one. There's a bolt-on DC electric motor (weighing just over 3kg or 7lb) just above the back wheel, behind the police officer's foot, pressing against the tire and driving it by simple friction. The motor's powered by a compact lead-acid battery (weighing about 5.5 kg or 12 lb) inside a protective nylon bag. This kit adds quite bit of weight to the bike, but gives extra range and speed when needed. Photo taken in Santa Rosa, California by Rick Tang courtesy of US DOE/NREL.
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
It is very important that sensors work well and that they are integrated/tuned for good usability. Although ebikes do need some initial mental adjustment from riders, some model do much better then others, e.g. most testers seem to prefer the TDS Impluse over the Stöckli E.T. over the Stromer (which model?) with respect to reactivity. Of course, usability is subjective and some people may prefer one behavior over an other. However, cheap bikes may be just plain bad and this is why test driving is important.
Pedelec is a European term that generally referred to an electric bicycle that incorporated a torque and/or a speed sensor and/or a power controller that delivered a proportionate level of assist and only ran when the rider pedaled. On the opposite side, a Noped is a term used by the Ministry of Transportation of Ontario for similar type vehicles which do not have pedals or in which the pedals have been removed from their motorized bicycle. Finally, Assist Bicycle is the technical term used to describe such a vehicle and Power-Assisted Bicycle is used in the Canadian Federal Legislation, but is carefully defined to only apply to electric motor assist, and specifically excludes internal combustion engines (though this is not the case in the United States).
"Electric-assisted bicycle" means a bicycle with two or three wheels, a saddle, fully operative pedals for human propulsion, and an electric motor. The electric-assisted bicycle's electric motor must have a power output of no more than one thousand watts, be incapable of propelling the device at a speed of more than twenty miles per hour on level ground, and be incapable of further increasing the speed of the device when human power alone is used to propel the device beyond twenty miles per hour.[66]
Track bicycles do not have brakes, because all riders ride in the same direction around a track which does not necessitate sharp deceleration. Track riders are still able to slow down because all track bicycles are fixed-gear, meaning that there is no freewheel. Without a freewheel, coasting is impossible, so when the rear wheel is moving, the cranks are moving. To slow down, the rider applies resistance to the pedals, acting as a braking system which can be as effective as a conventional rear wheel brake, but not as effective as a front wheel brake.[51]
Bicycles featuring pedal power were developed during the subsequent decades of the 19th century, with the most emblematic example being the bicycle we know today as the Penny-Farthing. The bike was named based on the substantial difference in its wheel size resembling the larger and smaller Penny and Farthing coins, respectively. These bicycles were wildly popular among the well heeled upper classes of Europe and America despite their penchant for launching riders head first over the large wheel, not to mention their relative difficulty to mount and dismount.
In Manitoba Electric Bikes can be classified as a scooter or a moped/mobility vehicle depending on the power of the engine used and its top speed. If the engine on the Electric Bike is less than 50cc and it cannot exceed 50 km per hour the rider is not required to have a motorcycle licence or any specific training.[26] Electric Bikes can be driven by anyone with a Class 5 driver's licence in any stage of the graduated licensing process.[27] A Class 5 Learners Licence requires one to be age 16 (parents consent if under 18) and a visit to a licensing office to pass a vision test and a written knowledge test about the rules of the road and traffic signs.[28]
GPS Firmware: This net update will be much appreciated by people who have a GPS Analogger device with their CA3. With a simple hardware modification to the Analogger circuit, the GPS data will be transmitted from your existing TRS cable back to the Cycle Analyst. You can then see the time of day, your elevation, position, and direction all on the CA3 screen. The firmware also features additional custom views on the main screen, allowing you to replace or toggle the battery voltage with any of these new parameters to get just the display you are after.
Before you start shopping around for a new e-bike, the first thing you should ask yourself is, “how do I plan on using an electric bicycle?” How far do you plan on traveling? What type of terrain will you be traveling on? How much assistance do you need? Do you plan on pedaling – or do you want the bike to do all the work? Is this bike for daily commuting or casual riding? How fast do you need to go?
When last checked, no E-bikes satisfied this requirement, so ebikes cannot be registered in New Jersey.[108] However, NJ Bill A2581, introduced March 22, 2010, would permit the use of low-speed electric bicycles upon the roadways and bicycle paths in NJ, where a low-speed electric bicycle is defined as a two-wheeled vehicle with fully operable pedals for human propulsion and an electric motor of less than 100 pounds and 750 watts, whose maximum speed on a paved level surface is less than 20 miles per hour.[109] The bill has been referred to the state's Assembly Transportation, Public Works and Independent Authorities Committee.[110]
When I finally had the ability drive this thing in my city, it feels fantastic, you're cruising easily. But the minute it starts going up a hill, you also gotta peddle to help it go up. Which is okay because the little engine helps a lot so you're not straining yourself. But, being that the wheels are so small, after a while, you feel your legs get swore. I guess the size of the wheel
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle(they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.

The great majority of modern bicycles have a frame with upright seating that looks much like the first chain-driven bike.[7][8][9] These upright bicycles almost always feature the diamond frame, a truss consisting of two triangles: the front triangle and the rear triangle. The front triangle consists of the head tube, top tube, down tube, and seat tube. The head tube contains the headset, the set of bearings that allows the fork to turn smoothly for steering and balance. The top tube connects the head tube to the seat tube at the top, and the down tube connects the head tube to the bottom bracket. The rear triangle consists of the seat tube and paired chain stays and seat stays. The chain stays run parallel to the chain, connecting the bottom bracket to the rear dropout, where the axle for the rear wheel is held. The seat stays connect the top of the seat tube (at or near the same point as the top tube) to the rear fork ends.
This is a virtual hello to all the people who came by our booth last weekend at the BC Bike Show and are just now visiting our webpage for the first time. We had a great time and were delighted to see how much this event has grown recently. (And to those who lament that the bike show is now totally taken over by ebikes, well it's been over 15 years now that we've been trying to tell you all this day was coming!)
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[142]
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2 [123] as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
Earlier UK regulations required that the motor has an average power output limited to 200 W (250 W for tricycles and tandems) and weight limited to 40 kg (60 kg for tricycles and tandems). These regulations must come in-line with the EU regulations by (find deadline). For models sold before June 2003, e-bikes conforming to the speed, weight and power limits may also be considered pedal cycles. Electric bikes with higher power outputs, or those not meeting the "pedelec" definition are now treated as motorcycles and require a license.
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:
×