Bicycle manufacturing proved to be a training ground for other industries and led to the development of advanced metalworking techniques, both for the frames themselves and for special components such as ball bearings, washers, and sprockets. These techniques later enabled skilled metalworkers and mechanics to develop the components used in early automobiles and aircraft.


Different gears and ranges of gears are appropriate for different people and styles of cycling. Multi-speed bicycles allow gear selection to suit the circumstances: a cyclist could use a high gear when cycling downhill, a medium gear when cycling on a flat road, and a low gear when cycling uphill. In a lower gear every turn of the pedals leads to fewer rotations of the rear wheel. This allows the energy required to move the same distance to be distributed over more pedal turns, reducing fatigue when riding uphill, with a heavy load, or against strong winds. A higher gear allows a cyclist to make fewer pedal turns to maintain a given speed, but with more effort per turn of the pedals.
Great bike. Easy to assemble by yourself but if you have a rack let pros do it. No charge for that. Contacted the Addmotor people a few times and they got back quickly even on weekends. Great service. Bike is solid as a rock and excellent components. Only drawback is lack of fenders which I hope someone can manufacture. I would buy again in a nano second!
We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.
Regulations[37] appear to deal with Bicycles with helper motors. No person shall ride a bicycle with a helper motor unless that person holds a valid motor vehicle operator's license. No person shall operate a bicycle with a helper motor at a rate of speed exceeding thirty miles per hour; nor shall any bicycle with a helper motor be operated on any sidewalk, limited access highway or turnpike. Driver's licence is required except if a special permit is obtained by havnig a doctor fill out a certificate and shows they are able to drive the bike with and without the motor assisting.
Bicycles helped create, or enhance, new kinds of businesses, such as bicycle messengers,[92] traveling seamstresses,[93] riding academies,[94] and racing rinks.[95][94] Their board tracks were later adapted to early motorcycle and automobile racing. There were a variety of new inventions, such as spoke tighteners,[96] and specialized lights,[91][96] socks and shoes,[97] and even cameras, such as the Eastman Company's Poco.[98] Probably the best known and most widely used of these inventions, adopted well beyond cycling, is Charles Bennett's Bike Web, which came to be called the jock strap.[99]

You can learn more about the development and axle testing process on this endless-sphere thread. Our ambition is to make this splined axle design into a new standard that we deploy across our entire higher power motor lines to replace axle flats. If you're as excited as us and want to jump right into ordering, we have the first production shipment on hand available in bare motors and complete kits.
We rode the Vado through the gauntlet, including some of the steepest hills in Palo Alto, and it easily handled everything we threw at it, maintaining a steady 20 miles per hour even on the most daunting of ascents. The bike also handles well on downhills and is both nimble and quick on city streets and paved trails. It’s even comfortable to ride for extended distances, which is vitally important for any bike built for urban settings.
The environmental effects involved in recharging the batteries can of course be reduced. The small size of the battery pack on an e-bike, relative to the larger pack used in an electric car, makes them very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots", in which e-bike riders can charge their vehicles while parked under photovoltaic panels.[66]
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles,[77] including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity.[78] A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.[79]
By Max Shumpert: This article has been updated to reflect the most accurate information regarding best e-bikes available for those who are interested in new technology combined with traditional bikes. The best 5 available have changed, and information has been added to assist individuals in finding the best electric bicycles currently available on the market. The FAQ has also been updated.
Maybe the most confusing legal issue facing e-bike riders today is the difference between a bike lane and bike path. A bike lane is a marked section of roadway shared with motor vehicles. Bike paths pretty much universally prohibit the use of motorized vehicles. Still, you will need to research your area. As an example: “A path near our office specifically says “no motorized bicycles.” Yet, when we tracked down an employee who claimed to work enforcement on the path, he said that our e-bike was allowed.”8
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.
Having spent some quality time with Wing’s e-bike, I understand why so many people are excited about the growing popularity of electric-powered vehicles like bikes and scooters. They take a lot of the work out of getting from point A to point B, while retaining all of the joy. They can give you more confidence when navigating a treacherous city terrain that prioritizes cars over people. And let’s face it: bikes are cool, and always will be.
Template:Cleanup Template:Split Many countries have Electric bicycle laws which legislated to one extent or another the legality of Electric Bicycles. Countries Like the United States and Canada have Federal regulations governing the safety requirements and standards of manufacture. Other countries like the Signatories of the European Union have agreed to wider ranging legislation covering use and safety for what they term EPAC(Electric pedal assisted cycles).
Tires vary enormously depending on their intended purpose. Road bicycles use tires 18 to 25 millimeters wide, most often completely smooth, or slick, and inflated to high pressure in order to roll fast on smooth surfaces. Off-road tires are usually between 38 and 64 mm (1.5 and 2.5 in) wide, and have treads for gripping in muddy conditions or metal studs for ice.
Built around a heavy-duty alloy frame, the GSD eschews many of the traits of other cargo bikes: long wheelbases, bigger wheels, and especially, an unwieldy ride. Yet it boasts an extensive capacity, nimble handling—even fully loaded, thanks to a short wheelbase and 20-inch wheels—and enduring range in a package not much bigger than most non-cargo e-bikes. The stout frame holds a 250-watt Bosch motor that gives up to 275 percent of your power back to the pedals and reaches 20 mph. The GSD has room for two battery packs, extending the batteries’ combined range to a claimed 150 miles and making the Tern one of the longest-lasting e-bikes on the market. A laundry list of accessories and a (claimed) 396-pound carrying capacity round out the GSD’s status as an epic day-tripper.
Vehicles with an electric power and power of less than 300W are classified as "not a motor vehicle". Such electric bicycles must comply with the same rules as bicycles. You must wear a helmet even on a scooter or bike under 300W. If the power is over 300W or a combustion engine is used it is a "low powered vehicle" and the moped rules apply. Specifically, a drivers license and registration are required.
Motor position – e-bike motors are positioned on either the front wheel hub, rear wheel hub, or in the middle of the bike between the pedals. There are pros and cons of each, but we think the mid-engine motor gives better weight distribution and the most natural bike riding feel. The pulling sensation you get from a front hub motor in particular can feel a bit unnatural
Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[68] 

As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170 pound rider when powered only by that engine. (AB441, amending NRS 480, 482 and other sections)
As of 2008 a standard class C license, proof of insurance, and registration (annual fee: $9.00) are required for operation of any motorized pedalcycle in Pennsylvania. Additionally, there are strict equipment standards that must be met for operation, including: handlebars, brakes, tires/wheels, electrical systems/lighting, mirrors, speedometer, and horns/warning devices.[127]
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers.  If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.  
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170 pound rider when powered only by that engine. (AB441, amending NRS 480, 482 and other sections)
This is a virtual hello to all the people who came by our booth last weekend at the BC Bike Show and are just now visiting our webpage for the first time. We had a great time and were delighted to see how much this event has grown recently. (And to those who lament that the bike show is now totally taken over by ebikes, well it's been over 15 years now that we've been trying to tell you all this day was coming!)

I bought this bike from a dealer after extensive research on ebikes. The Elby is on par with European commuter ebikes at a better price point, you get a lot for your $ here. Elby is the complete package commuter: lights & a USB charger (for a phone or whatever) are integrated into the motor’s power supply and wired inside the frame. Rugged fenders have heavy-duty cross braces to attach baskets and whatnot. Thick Continental tires make for a comfy ride. The step-through frame is very convenient, built stout enough to carry me (200#) and two loaded baskets down hills and around curves with perfect stability. The motor on this bike is in the rear hub, and having it behind me makes it virtually soundless. The motor (BionX 500 watt) kicks in as soon as you start pedaling, but there is a
The Domane+ e-road bike is the electric version of Trek’s popular Domane. It’s designed for riders who appreciate that bike’s reliable comfort and IsoSpeed technology but want the added fun and function of e-assist. It’s also the ideal companion for anyone coming back from injury, slower riders who want to mix it up with a speedy group, and couples with different fitness levels. A Bosch Performance Line Speed motor provides a very welcome 28 mph of pedal assist, and the 500Wh Powertube battery sleekly integrates into the down tube. Also integrated: front and rear lights, which are powered by the battery—no charging required.
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle(they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.
And let’s not forget the economic advantages of owning an e-bike. The annual cost of running a new family car is, on average, about $9,000 per year. Running an electric bike costs around $400 per year. And while filling a gas tank costs around $30, recharging an electric bike battery costs only about 50 cents. A tank of gas may get you further, but not 60 times further!

My one complaint is the bike’s weight. This sucker is heavy! The aluminum frame looks light, but the the hub motor (4 pounds) and battery (5 pounds) add up. The bike’s total weight is 39 pounds, which is about average for e-bikes but not something you’d want to lug around all day. “This is not a solution for everybody,” Miller admits. “If you live in a fifth floor walkup this is probably not going to work.”


Electric-assisted bicycle operators must follow the same traffic laws as operators of motor vehicles (except those that by their nature would not be relevant). The bicycles may be operated two abreast. Operators must generally ride as close as is practical to the right-hand side of the road (exceptions include when overtaking another vehicle, preparing for a left turn, and to avoid unsafe conditions). The bicycle must be ridden within a single lane. Travel on the shoulder of a road must be in the same direction as the direction of adjacent traffic.
I waited until I hit 100 miles on this beauty before writing this review. My riding buddies told me I couldn't get a quality ebike for under $3k. Absolutely the wrong advice. This Addmotor is amazing in every way. Well built, close attention to detail and a complete joy to ride. I would highly recommend this bike to anyone looking for a great ebike experience.
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[65]
An electric bicycle is a bicycle with an electric motor used to power the vehicle, or to assist with pedaling. In many parts of the world, electric bicycles are classified as bicycles rather than motor vehicles, so they are not subject to the same laws as motor vehicles. Electric bicycles are one type of motorized bicycle. However, electric bicycles are defined separately and treated as a specific vehicle type in many areas of legal jurisdiction.
"Electric-assisted bicycle" means a bicycle with two or three wheels, a saddle, fully operative pedals for human propulsion, and an electric motor. The electric-assisted bicycle's electric motor must have a power output of no more than one thousand watts, be incapable of propelling the device at a speed of more than twenty miles per hour on level ground, and be incapable of further increasing the speed of the device when human power alone is used to propel the device beyond twenty miles per hour.[66]
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]
Both bikes have passable cadence sensor pedal assist that kicks in a little late and lets go a little early. Torque sensors are too expensive for this price level so you are just not going to get the same responsiveness as a bike store e-bike. Rattan has 5 levels of pedal assist while the Ancheer has 3. Over long periods of pedaling the PAS evens out or you can just use the throttle.
In addition, we have a new lineup of torque sensors from NCTE to replace the long out-of-stock THUN devices. This restores the option for a true transducer that measures the actual spindle torsion. They provide an accurate human watts readout, and unlike other sensors they can be used in mid-drive setups where the motor is driving the right side chain.
I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.

Electric mountain bikes have garnered a lot of attention for their ability to help riders go higher, further, and faster on the trail. As a result, there have been some impressive new eMTB models to hit the market in recent years, making it easier than ever to head off-road. Our favorite is the Haibike SDURO HardNine, which comes equipped with a 350-watt Bosch Performance CX drive and a 500 watt-hour battery. This gives it a range of up to 70 miles, along with a top speed of 20 mph, which is plenty fast on singletrack.
I like this little electric "scooter" a lot. I do think the rear wheels should be a bit further apart for added stability. I have also found it is too easy to "spin out" the front driver wheel when going up an incline or crossing a grass area. The user and assembly manual is minimal and could use considerably more information and more and better illustrations.
One of the most important categories of ebikes is the low-cost, entry-level sector. What I call the eBigBox models.  Obviously, not everyone can’t afford a $7500 Riese and Muller and frankly a lot of people are skeptical on how much they will use and enjoy an ebike. So even if they can afford a few thousand dollars for an ebike, they might not want to put it all down on a category they aren’t sure about.

Controllers for brushed motors: Brushed motors are also used in e-bikes but are becoming less common due to their intrinsic lower efficiency. Controllers for brushed motors however are much simpler and cheaper due to the fact they don't require hall sensor feedback and are typically designed to be open-loop controllers. Some controllers can handle multiple voltages.


In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.

FuroSystems’ two new full carbon fiber electric bikes are now available at discounted launch prices! The bikes are a folding e-bike and a mountain e-bike. FuroSystems has designed very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and is currently sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.
Oregon Law (ORS 801.258) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed no greater than 20 miles per hour on level ground.[54]
In the 1890s, electric bicycles were documented within various U.S. patents. For example, on 31 December 1895, Ogden Bolton Jr. was granted U.S. Patent 552,271 for a battery-powered bicycle with "6-pole brush-and-commutator direct current (DC) hub motor mounted in the rear wheel". There were no gears and the motor could draw up to 100 amperes (A) from a 10-volt battery.[5]
The pedals on a motorised bicycle must be the primary source of power for the vehicle. If the motor is the primary source of power then the device cannot be classed as a motorised bicycle. For example, a device where the rider can twist a throttle and complete a journey using motor power only without using the pedals, would not be classed as a motorised bicycle.
“Changes in production and consumption patterns are a crucial element of the sustainability agenda. Communication between product developers and users, and user integration in product development, can serve as a means for organizational as well as individual learning processes, resulting in sustainable product development. [...] Improved methods, such as INNOCOPE (innovating through consumer-integrated product development), tested in this study with a cycle manufacturer and resulting in a new product, a pedelec, are needed for effective communication, activating consumers and enabling them to promote sustainability goals. Through co-operative product development processes key factors facilitating and obstructing the adoption of sustainable innovations may be identified. Such processes can enhance the emergence and diffusion of sustainable product innovations and different forms and bodies of knowledge can be combined. Integrating users' contextual everyday knowledge of the product with the technical knowledge of companies may lead to mutual learning, technical innovations and changes in consumer behaviour.” (Hoffmann, 2007).
I called Geico earlier today. They could insure me with Renters Insurance, but … I would need to have a Renter's Policy first, before the secondary insurance company they deal would insure my two bikes (Surly Long Haul Trucker and Yuba Sweet Curry custom eBike). BUT … unfortunately …. The company that would insure my bicycles will NOT insure me because we have a Pitbull !!! Can you believe that … !!!
Experiments done in Uganda, Tanzania, and Sri Lanka on hundreds of households have shown that a bicycle can increase a poor family's income as much as 35%.[69][better source needed][70][71] Transport, if analyzed for the cost-benefit analysis for rural poverty alleviation, has given one of the best returns in this regard. For example, road investments in India were a staggering 3–10 times more effective than almost all other investments and subsidies in rural economy in the decade of the 1990s. What a road does at a macro level to increase transport, the bicycle supports at the micro level. The bicycle, in that sense, can be an important poverty-eradication tool in poor nations.
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.
The Shift S1 isn’t going to blow anyone away with amazing performance, but it is peppy enough to have a lot of fun on. And if you mostly travel by rideshares like Uber or scootershares like Bird, you can probably pay for the S1 after just a few months of cutting out app-based transportation. It’s hard to ask for too much more from such an inexpensive e-bike.

As is the case with any e-bike assembled from Chinese parts, Wing has its share of clones that can be found for sale on sites like IndieGoGo and Kickstarter. For example, the Danish company Strom Bikes has a model for city biking that also looks incredibly similar to Wing’s Freedom — and is apparently several hundred dollars cheaper too. This is also commonly found with electric scooters, with startups buying Chinese-made models and rebadging them for sale in the US.


During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.
The E-bike is everything it was advertised to be. It's big and fast and fun to ride especially when riding uphill with pedal assist you have the superhuman ability to get up those tuff climbs that would normally leave you winded and probably walking the bike. The setup was fairly simple however the frame had a couple of serious deep scratch marks in the otherwise impeccable paint job. And even though it's purely cosmetic it was still very disappointing to receive a brand new bike in this condition. It's not clear to me what if anything I can do about it but I still love the bike.
The Ohio Revised Code 4511.01 [121] distinguishes motorized bicycles and mopeds from motorcycles or scooters by describing them as "...any vehicle having either two tandem wheels or one wheel in the front and two wheels in the rear, that is capable of being pedaled and is equipped with a helper motor of not more than fifty cubic centimeters piston displacement that produces no more than one brake horsepower and is capable of propelling the vehicle at a speed of no greater than twenty miles per hour on a level surface." One brake horsepower converts to 0.75 kW, or (rounded) 750W. Thus, a bicycle with an electric helper motor operating under 750W, and not propelling the bicycle over 20 mph, does not qualify to be registered under Ohio state law. Local jurisdictions may have other regulations.

Hmm, I think it depends on the forest. My experience has been that if you have a Class 1 ebike and are riding respectfully, most places allow it. I have a sensitive knee and carry a doctor’s note citing disability laws in Colorado and have never been approached or asked by a ranger or fellow rider about the legality of my bike. That said, I have been using the really quiet and hidden Brose motor and I ride carefully and am friendly with everyone
No person may drive either a two-wheeled or a three-wheeled motorcycle, or a motor-driven cycle unless such person has a valid driver's license specially endorsed by the director to enable the holder to drive such vehicles. No driver's license is required for operation of an electric-assisted bicycle if the operator is at least sixteen years of age. Persons under sixteen years of age may not operate an electric-assisted bicycle. Persons operating electric-assisted bicycles shall comply with all laws and regulations related to the use of bicycle helmets. Electric-assisted bicycles and motorized foot scooters may have access to highways of the state to the same extent as bicycles. Electric-assisted bicycles and motorized foot scooters may be operated on a multipurpose trail or bicycle lane, but local jurisdictions may restrict or otherwise limit the access of electric-assisted bicycles and motorized foot scooters, and state agencies may regulate the use of motorized foot scooters on facilities and properties under their jurisdiction and control.
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.[23][24][25]
×