Bicycle manufacturing proved to be a training ground for other industries and led to the development of advanced metalworking techniques, both for the frames themselves and for special components such as ball bearings, washers, and sprockets. These techniques later enabled skilled metalworkers and mechanics to develop the components used in early automobiles and aircraft.
Motor-driven cycles may be operated on the roadway without registration, but the operator must have a driver's license.[85] The cycle may not be operated on any sidewalk, limited access highway or turnpike. If the maximum speed of the cycle is less than the speed limit of the road, the cycle must operate in the right hand lane available for traffic or upon a usable shoulder on the right side of the road unless the operator is making a left turn.
An anti-theft radio GPS that mounts to standard bottle cage bosses and can locate within 9 feet, it runs on the Verizon network and costs $5/mo in addition to the hardware. Integrated vibration sensing alarm sends an automated text message alerting you anytime the bike has been "locked" using the companion smartphone application (Android or iOS)...

I've put almost1 thousand miles on the bike in 2 months, and so far I love it! Using the just electric mode only go about 12-13 miles an hour on level ground and I only weigh about 160. So it's not real powerful. But on pedal assist it works great up hills. It folds up quick and easy. It's a real pain putting the rear wheel back on if you get a flat so I recommend getting tire linners. It also would be nice if you could charge the battery off the bike. I think it's well worth the money! Great bike ! Its made it through lots of abuse even through miles of down pouring rain!
State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.

Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.[5]
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.
"Bicycle" means either of the following: (1) A device having two wheels and having at least one saddle or seat for the use of a rider which is propelled by human power. (2) A device having two or three wheels with fully operable pedals and an electric motor of less than 750 watts (one horsepower), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden, is less than 20 miles per hour.[citation needed],
This little bike is great I weight like 175 and it's just great it can go up hills and it's an awesome little bike for NYC cops give me no issues and with a phone mount you can see your speed and battery life you have left... It's just a great bike nice and light I can pick up with one hand and it folds. The only cons I would say is I wish the battery lasts longer I get around 6.5 miles at full throttle at varying terrain and the horn is weak, I installed an air horn on my bike
China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008,[72] and reaching an estimated fleet of 120 million e-bikes in early 2010.[2][73] This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities.[72] Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car.[2] Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007.[73] By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.[72][73]

In addition, Kalk weighs under 155 pounds — less than half of traditional motorbikes. Cake customized parts of the drivetrain and implemented an interior permanent magnet (IPM) motor. On a single charge, the bike travels up to 50 miles and as a bonus feature, maintenance is minimal due to the fact there are few moving parts thanks to its lack of a combustion engine.
Put the wheel with the electric hub on your bike and connect the brake components. Simply reverse the process you used to remove the wheel in order to reinstall it. Be sure to adjust the chain so it fits properly if you’re replacing the back wheel. If the bike has rim or cantilever brakes, simply close them over the new wheel using the lever. If the bike has disc brakes, put the pads back in place and secure them using the clips, springs, or cotter or retaining pin.[11]

FuroSystems’ two new full carbon fiber electric bikes are now available at discounted launch prices! The bikes are a folding e-bike and a mountain e-bike. FuroSystems has designed very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and is currently sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.

Bosch eBike Systems – eBikes 101 What is an eBike? The eBike is one of the most agile, comfortable vehicles of our time. With the positive impacts on health, environment and society, electric bikes bring a new meaning to smart mobility. Their modern components and simple yet innovative design allow for a variety of eBiking adventures, from trekking through the …
Storage space: it’s one of the primary disadvantages to biking versus driving. A simple solution is attaching a basket or storage case to your bike’s frame or handlebars, giving you a convenient place to keep your essentials while you ride. A pannier rack is a useful option as well, which allows you to connect special pannier bags to your bike to create even more storage capacity.

In the theoretical electric bike we considered up above, we had the dynamo/motor driving the back wheel directly, simply by pressing on the tire. Most electric bikes work a different way. They have compact electric motors built into the hub of the back or front wheel (or mounted in the center of the bike and connected to the pedal sprocket). Take a look at the hub of an electric bike and probably you'll see it's much fatter and bulkier than on a normal bike. You can read more about how these motors work in our main article about hub motors.
The first functioning electric motor was displayed in the early 19th century, though the device constructed by British scientist Michael Faraday did little more than swirl a wire around a magnet when an electric charge was introduced. Still, the concept proved that electricity could do work. Functional electric motors would follow in many forms after that achievement in 1821. Soon scientists and tinkerers around the world, including visionaries such as Nikola Tesla, were experimenting with all manner of electric motors -- some worked with DC power, others with AC. By the end of the century, myriad electric motors had been produced, capable of exerting enough force with enough reliable control that they were practical for use in myriad applications.
eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …
There are a variety of gadgets in the market for a hunter. These gadgets have made the hunting experience a lot easier and better. However, not everyone requires everything available in the market. It’s from your experience you learn what is best for you. Let’s look at some important gadgets you may want to have on your next hunting trip.   Electric Hunting Bikes Electric hunting bikes are a better bet than the dirt bikes or ATV’s. It makes lesser noise than the other modes of transport so you don't spook the wildlife. You can carry your gadgets and hunting...
This is a cool eBike fits in your car's trunk or back seat! It's well made. And it only has one rear disc brake, you dont really need the front brake. It's simple to operate and fun to use - just put one foot on one foot attachment while turning the throttle slightly, then as soon as you start to move add the other foot...and let the joy ride begin!

I bought the 52v 13ah for my 1000w BBSHD build and it is working great. My bike tears it up pretty good with this battery pack. Hopefully I don't run into any problems but so far so good. One thing I learned the hard way - if you use a 52v pack with the 1000w bbshd your battery meter will no longer be accurate. That was one tough ride home with my heavy fat bike!
On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines. 

Bicycle brakes may be rim brakes, in which friction pads are compressed against the wheel rims; hub brakes, where the mechanism is contained within the wheel hub, or disc brakes, where pads act on a rotor attached to the hub. Most road bicycles use rim brakes, but some use disk brakes.[49] Disc brakes are more common for mountain bikes, tandems and recumbent bicycles than on other types of bicycles, due to their increased power, coupled with an increased weight and complexity.[50]
In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.

Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
Massachusetts General Laws define three classes of motorized two-wheeled vehicles: Motorcycle, Motorized bicycle, and Motorized scooter.[98] Although the definition of motorized scooter includes two-wheeled vehicles propelled by electric motors with or without human power, motorized scooter specifically excludes anything which falls under the definitions of motorized bicycle and motorcycle. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. Motorcycle includes any bicycle with a motor or driving wheel attached, with the exception of vehicles that fall under the specific definition of motorized bicycle. Thus, a pedal bicycle with an electric motor or a non-pedal bicycle with an electric motor, automatic transmission, and maximum speed of 30 miles an hour would fall under the definition of motorized bicycle. An electric bicycle that did not meet those restrictions would be either a motorized scooter or motorcycle, depending on specific characteristics.
I did my commute a few times with the Rattan and while I would never give up my “bike store” e-bike for this, it was a worthy substitute. It never gave out on the big hills, nor did I have to brake because I felt the bike was falling apart. The frame is a little small for 6-foot me but it only comes in one size. I really miss the low rolling drag of having road tires however and this is something that both Rattan and Ancheer could improve upon. I don’t think many people are seriously off-roading with these bikes. Put some Schwalbe Big Bens on there!
Both the Stromer and the Stoeckli are very nice looking designs and easy to handle. Reliability for both does not seem to be up to Swiss standards, e.g. some of the 2012 Stöcklis seem to have bad contacts. However, as of 2013, most of these problems should be fixed. The Cube got criticized for its battery/saddle system, but this has probably been fixed in more recent edition and it has less "punch" then the other's since the motor is smaller (324W?). I don't know about the BH Neo Nitro. Given the relatively low price of the BH Nitro, it may be the best buy in this category if you plan to cover smaller distances (the battery is limited to 9Ah, and Spain's industry does need some help ;) Anyhow, all of these models come with a variety of motors and country-specific modifications. E.g. in France, the BH Nitro comes with a 350W motor and is electronically limited to 25km/h, whereas in Switzerland you either can get a 500W - 45 km/h version or a 250W? - 25km/h version.
E-bikes are classed according to the power that their electric motor can deliver and the control system, i.e., when and how the power from the motor is applied. Also the classification of e-bikes is complicated as much of the definition is due to legal reasons of what constitutes a bicycle and what constitutes a moped or motorcycle. As such, the classification of these e-bikes varies greatly across countries and local jurisdictions.
Across Europe, where e-bikes were embraced by the public long before the rest of the world, e-bike growth has averaged in excess of 20 percent each year between 2014 and 2017, with a whopping 25.3 percent growth to a total of two million e-bike sales in 2017. Analysts predict that strong growth will continue, with worldwide e-bike sales expected to hit $23.83 billion by 2025. A lot of that growth will be right here in the US.
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
Electric bikes are becoming a convenient and fun way to commute around a city, but they can be pricey. The average e-bike can cost $3,000, with some models getting up to $5,000 or more. But these prices are dropping, as new models come onto the market — and if you don’t mind giving up some of the glossier, high-tech features like embedded digital displays, retractable cable locks, and and theft tracking and recovery, you can find a really good quality e-bike for under $1,500.
To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.

Since fat tire electric bikes are suitable for a wider variety of situations than a standard cruiser or commuter e-bike, they have the potential to appeal to more people. For example, hunters and campers are ideal candidates for fat tire e-bikes, as they’ll benefit greatly from the heavy-duty tires and powerful motor when they’re navigating difficult wooded trails with lots of gear.

Pedelecs are much like conventional bicycles in use and function — the electric motor only provides assistance, for example, when the rider is climbing or struggling against a headwind. Pedelecs are therefore especially useful for people in hilly areas where riding a bike would prove too strenuous for many to consider taking up cycling as a daily means of transport. They are also useful for riders who more generally need some assistance, e.g. for people with heart, leg muscle or knee joint issues.
The safety bicycle gave women unprecedented mobility, contributing to their emancipation in Western nations. As bicycles became safer and cheaper, more women had access to the personal freedom that bicycles embodied, and so the bicycle came to symbolize the New Woman of the late 19th century, especially in Britain and the United States.[8][73] The bicycle craze in the 1890s also led to a movement for so-called rational dress, which helped liberate women from corsets and ankle-length skirts and other restrictive garments, substituting the then-shocking bloomers.[8]

One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.


None of this would matter if the VanMoof Electrified S2 (and its close relative the X2) wasn't fun to ride, but it is a blast. Like the Brompton, it pulls off the neat trick of powering you along but giving the illusion that you're doing the work, reacting quickly and cleverly to the speed of your pedalling and the difficulty of any incline you're on. 
An e-bike is identified as a "motor assisted cycle" (MAC) in British Columbia, which differs from electric mopeds and scooters, which are "limited-speed motorcycles." Motor assisted cycles must: have an electric motor of no more than 500 W; have fully operable pedals; not be capable of propelling the device at a speed greater than 32 km/hr [19.9 mph]. The engine must disengage when (a) the operator stops pedaling, (b) an accelerator controller is released, OR (c) a brake is applied. A driver's license, vehicle registration, and insurance are all not required. A bike helmet must be worn.[22]

The batteries are the most important parts of the bike, because (if you don't do any pedaling) they contain all the power that will drive you along. Typical electric bike batteries make about 350–500 W of power (that's about 35–50 volts and 10 amps), which is about a quarter as much as you need to drive an electric toaster. In theory, you could use any kind of battery on a bicycle. In practice, however, you want to use something that stores lots of power without being too heavy—or you'll be using half your power just moving the battery along! That tends to rule out heavy lead-acid batteries like the ones that start cars, though some electric bikes do use them. Lightweight lithium-ion batteries, similar to those used in laptop computers, mobile (cellular) phones, and MP3 players, are now the most popular choice, though they're more expensive than older rechargeable battery technologies such as nickel-cadmium ("nicad"). Typical batteries will give your bicycle a range of 10–40 miles between charges (depending on the terrain) and a top speed of 10–20 mph (which is about the maximum most countries allow for these vehicles by law). You can extend the range by pedaling or free-wheeling some of the time.
This electric bike received a five star. The assembly was pretty simple. I ordered a set of lights and a over rear tire carrier rack from amazon that took longer to install than it took too assemble the bike.This is a solid built by that is attractive and worthy of this price point. The build quality of this bike was very good. So far I've done a few test and it runs perfect. I've put on 50+ miles on this bike and have used it on flat ground, dirt roads, rocky trails and grassy fields. The bike runs quicker than what I expected from a small 250 W hub motor. I really like it in almost every way.
E-bikes use rechargeable batteries, electric motors and some form of control. Battery systems in use include sealed lead-acid (SLA), nickel-cadmium (NiCad), nickel-metal hydride (NiMH) or lithium-ion polymer (Li-ion). Batteries vary according to the voltage, total charge capacity (amp hours), weight, the number of charging cycles before performance degrades, and ability to handle over-voltage charging conditions. The energy costs of operating e-bikes are small, but there can be considerable battery replacement costs. The lifespan of a battery pack varies depending on the type of usage. Shallow discharge/recharge cycles will help extend the overall battery life.
The Domane+ e-road bike is the electric version of Trek’s popular Domane. It’s designed for riders who appreciate that bike’s reliable comfort and IsoSpeed technology but want the added fun and function of e-assist. It’s also the ideal companion for anyone coming back from injury, slower riders who want to mix it up with a speedy group, and couples with different fitness levels. A Bosch Performance Line Speed motor provides a very welcome 28 mph of pedal assist, and the 500Wh Powertube battery sleekly integrates into the down tube. Also integrated: front and rear lights, which are powered by the battery—no charging required.
There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.
Built by a company that’s made cycling equipment for more than four decades, the Vado feels more like a traditional bicycle than almost any other ebike. Its frame and components have been tuned to provide a familiar experience, making it easy for new and long-time cyclists to jump on and start pedaling. Specialized’s heritage shines through nicely, helping separate itself from the competition in an increasingly crowded ebike market.

That being said, It is fun to ride - my 13 year old grandson likes it a lot. I feel it is best used on hard surfaces like sidewalks and hard floors. I received this little scooter 3 days ago and have ridden it in Costco and Sam's club and took it to an art show and sale as well as driving it through hospital halls on the way to and from a meeting.. One has to
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
Class 1 makes great inroads to establish set boundaries for off road/natural surface trail access for eMountain bikes. There is fierce resistance from some mountain biking purists to allow ebikes on trails. BPSA and IMBA have done good work to justify the impact of class 1 ebikes on natural surface trails, and eliminate the wear-n-tear argument, though IMBA members are not 100% on board.
As the managing editor of Ars Technica, one of my duties is to monitor the daily torrent of news tips and PR emails. The overwhelming majority of them is deleted after a glance, and the news tips and story ideas are passed along to the appropriate writer. Sometimes a product announcement will catch my eye, and I will follow up. Once in a blue moon, I'll say, "please send me one so that I may review it." And that's how I ended up riding an electric bike around the Chicago suburbs for two weeks.
To qualify as an electric-assisted bicycle under state law they need to have a seat and fully operable pedals for human propulsion, meet federal motor vehicle safety standards, an electric motor that has a power output of not more than 1,000 watts, maximum speed of not more than 20 mph (electric motor and human power combined), disengages or ceases to function when the vehicle’s brakes are applied, two or three wheels
In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris.[22] The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind).[23] It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.[24]

Photo: Could solar power be the future of electric bicycles? The large solar panel mounted over the back wheel of this experimental bike powers an electric motor connected by a chain drive to the back wheel, helping the rider when he doesn't feel like pedaling. Using clean, green solar power would remove the problem of having to charge electric bikes with electricity generated from fossil fuels—and help to extend their range significantly. Photo by Warren Gretz courtesy of US DOE/NREL.
"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption, [59][60][61][62][63][64] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
Bicycle shall mean (1) every device propelled solely by human power, upon which any person may ride, and having two tandem wheels either of which is more than fourteen inches in diameter or (2) a device with two or three wheels, fully operative pedals for propulsion by human power, and an electric motor with a capacity not exceeding seven hundred fifty watts which produces no more than one brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than twenty miles per hour on level ground.
Some prohibitions also apply, such as on: carrying cargo that prevents keeping at least one hand on the handlebars or prevents proper use of brakes, riding no more than two abreast on a roadway or shoulder, and attaching the bicycle to another vehicle. Minn. Stat. § 169.222, subds. 3-5. The vehicles may be operated on a sidewalk except in a business district or when prohibited by a local unit of government, and must yield to pedestrians on the sidewalk. Minn. Stat. § 169.223, subd. 3. By default, electric-assisted bicycles are allowed on road shoulders as well as on bicycle trails, bicycle paths, and bicycle lanes.

The federal Consumer Product Safety Act defines a "low speed electric bicycle" as a two or three wheeled vehicle with fully operable pedals, a top speed when powered solely by the motor under 20 mph (32 km/h) and an electric motor that produces less than 750 W (1.01 hp). The Act authorizes the Consumer Product Safety Commission to protect people who ride low-speed electric vehicles by issuing necessary safety regulations.[63] The rules for e-bikes on public roads, sidewalks, and pathways are under state jurisdiction, and vary.

×