DIY enthusiasts, with tens of thousands of converted bikes using throttle-only, 20+ mph kits, are now officially labeled Moped class. While these bikes handle and pedal-ride just as safely as the class 3 speed pedelecs in many cases, our DIY counterparts will be officially kicked out and left on their own for advocacy and legal acceptance in California. This is a big deal, without a class sticker, any DIY electric bike conversion kit is considered a Moped and not a bicycle.
As of 2005, where Federal funds have been used in the construction of bicycle or pedestrian paths motor vehicles including electric bicycles (here defined as having a motor weighing less than Template:Convert) are not permitted unless State or Local regulations permit [25]. This was known as the Transportation Equity Act for the 21st Century (TEA-21), or Public Law 105-178, or by its 2003 re-authorization which expired in 2005 the Safe, Accountable, Flexible, Efficient Transportation Equity Act (SAFETEA-LU).[26][27]

China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008,[72] and reaching an estimated fleet of 120 million e-bikes in early 2010.[2][73] This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities.[72] Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car.[2] Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007.[73] By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.[72][73]


In Norway, e-bikes are classified as ordinary bicycles, according to the Vehicle Regulation (kjøretøyforskriften) § 4-1, 5g. Hence, e-bikes are not registered in the Vehicle Registry, and there is no demand for a license to drive them. Still, there are constraints on the bicycle construction. The maximum nominal motor power output can be no more than 250 watts and the maximum performance speed of the vehicle when the engine is running is 25 km per hour (15 mph).[40] A function that reduces motor power when vehicle speed exceeds 25 km per hour is mandatory. However, if the motor is not running, the e-bike, or any other bike, answer only to the constraints of the ordinary speed limits.
No person may drive either a two-wheeled or a three-wheeled motorcycle, or a motor-driven cycle unless such person has a valid driver's license specially endorsed by the director to enable the holder to drive such vehicles. No driver's license is required for operation of an electric-assisted bicycle if the operator is at least sixteen years of age. Persons under sixteen years of age may not operate an electric-assisted bicycle. Persons operating electric-assisted bicycles shall comply with all laws and regulations related to the use of bicycle helmets. Electric-assisted bicycles and motorized foot scooters may have access to highways of the state to the same extent as bicycles. Electric-assisted bicycles and motorized foot scooters may be operated on a multipurpose trail or bicycle lane, but local jurisdictions may restrict or otherwise limit the access of electric-assisted bicycles and motorized foot scooters, and state agencies may regulate the use of motorized foot scooters on facilities and properties under their jurisdiction and control.
Massachusetts General Laws define three classes of motorized two-wheeled vehicles: Motorcycle, Motorized bicycle, and Motorized scooter.[98] Although the definition of motorized scooter includes two-wheeled vehicles propelled by electric motors with or without human power, motorized scooter specifically excludes anything which falls under the definitions of motorized bicycle and motorcycle. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. Motorcycle includes any bicycle with a motor or driving wheel attached, with the exception of vehicles that fall under the specific definition of motorized bicycle. Thus, a pedal bicycle with an electric motor or a non-pedal bicycle with an electric motor, automatic transmission, and maximum speed of 30 miles an hour would fall under the definition of motorized bicycle. An electric bicycle that did not meet those restrictions would be either a motorized scooter or motorcycle, depending on specific characteristics.
Übrige "Motorfahrräder": “E-Bikes mit einer Leistung zwischen 500 und 1000 Watt oder einer bauartbedingten Höchstgeschwindigkeit von 20 bis 30 km/h oder einer Tretunterstützung, die auch bei einem Tempo von 25 – 45 km/h wirkt, gelten als Motorfahrräder und benötigen ein entsprechendes Kontrollschild.”. You can use any bicyle path and also hiking roads forbidden to motorbikes if you drive slowly.

The Ancheer comes with outstanding Shimano Tourney gears in 6 x speeds. This gear system is one of the best in the business. Similarly the front-rear disc brakes are perfectly effective and will bring you to a safe stop even from speed. Speaking of speed, the maximum is 16mph and the bike will travel anywhere between 17-23 miles on a single charge. The battery charges up in 4-6 hours, which is the same for virtually all e-bikes.
I discovered these downsides when, on my third day with the bike, I got a flat tire and had to carry it onto the subway with me for those last few miles back to my apartment. The cause of the flat is unknown; the bike mechanic who eventually fixed it didn’t see anything wrong with the rims. But the experience of trying to maneuver an almost 40 pound e-bike on and off a crowded subway car during rush-hour is not one I can recommend.
Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.[16]

Both the Stromer and the Stoeckli are very nice looking designs and easy to handle. Reliability for both does not seem to be up to Swiss standards, e.g. some of the 2012 Stöcklis seem to have bad contacts. However, as of 2013, most of these problems should be fixed. The Cube got criticized for its battery/saddle system, but this has probably been fixed in more recent edition and it has less "punch" then the other's since the motor is smaller (324W?). I don't know about the BH Neo Nitro. Given the relatively low price of the BH Nitro, it may be the best buy in this category if you plan to cover smaller distances (the battery is limited to 9Ah, and Spain's industry does need some help ;) Anyhow, all of these models come with a variety of motors and country-specific modifications. E.g. in France, the BH Nitro comes with a 350W motor and is electronically limited to 25km/h, whereas in Switzerland you either can get a 500W - 45 km/h version or a 250W? - 25km/h version.
In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors.[1] Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.

Our hope is that this plug will become to motors in the 500-1500 watt power range what the 9pin Z910 became for the low power geared motors, with all motor manufacturers agreeing to the same pinout standard for easy swapping and interchangeability . We have an L10 version of the Phaserunner motor controller available now and will soon be expanding this to a Grinfineon offering as well.
I do not recommend hacking a bike into s-pedelec, i.e. make a 25km/h bike go at 45 or faster. If you have an accident you will be in trouble. Just get a legal version. In addition you will have good insurance. Of course, in countries like France or the UK that so far do not know S-Pedelecs, you will have to make a difficult moral choice.... At least, make sure that your rig is safe...

In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors.[1] Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.
Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an e-bike dubbed Zike.[9] The bicycle included NiCd batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial e-bikes were available.

Bicycle suspensions are used primarily on mountain bicycles, but are also common on hybrid bicycles, as they can help deal with problematic vibration from poor surfaces. Suspension is especially important on recumbent bicycles, since while an upright bicycle rider can stand on the pedals to achieve some of the benefits of suspension, a recumbent rider cannot.
eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …
I bought this bike from a dealer after extensive research on ebikes. The Elby is on par with European commuter ebikes at a better price point, you get a lot for your $ here. Elby is the complete package commuter: lights & a USB charger (for a phone or whatever) are integrated into the motor’s power supply and wired inside the frame. Rugged fenders have heavy-duty cross braces to attach baskets and whatnot. Thick Continental tires make for a comfy ride. The step-through frame is very convenient, built stout enough to carry me (200#) and two loaded baskets down hills and around curves with perfect stability. The motor on this bike is in the rear hub, and having it behind me makes it virtually soundless. The motor (BionX 500 watt) kicks in as soon as you start pedaling, but there is a

Today, China is the world's leading producer of electric bicycles. According to the data of the China Bicycle Association, a government-chartered industry group, in 2004 China's manufacturers sold 7.5 million electric bicycles nationwide, which was almost twice the year 2003 sales;[8] domestic sales reached 10 million in 2005, and 16 to 18 million in 2006.[9] By 2007, electric bicycles were thought to make up 10 to 20 percent of all two-wheeled vehicles on the streets of many major cities.[9] A typical unit requires 8 hours to charge the battery, which provides the range of 25–30 miles (40–50 km),[9] at the speed of around 20 km/h.[8]


It’s a topic that many eMTBers are interested in: fast charging. What has long been a reality with electric cars is now also being partly improved for ebikes with high amperage chargers. Bosch has presented a 6A charger this year that can charge a 500 Wh battery in 3 hours, more than a third faster than the standard charger. The new benchmark next year, however, will probably be the 10A charger presented by Haibike and BMZ. It is claimed to be capable of charging a 630 Wh battery in just 1.5 hours. 

During nighttime operation, the bicycle must be equipped with a front headlamp, a rear-facing red reflector, and reflectors on the front and rear of pedals, and the bicycle or rider must have reflective surfaces on each side. Minn. Stat. §169.222, subd. 6. An electric-assisted bicycle can be equipped with a front-facing headlamp that emits a flashing white light, a rear-facing lamp that has a flashing red light, or both. The bicycle can carry studded tires designed for traction (such as in snowy or icy conditions).
State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[55] Subchapter J of Publication 45 spells out the vehicle requirements in full.
E-bikes can be a useful part of cardiac rehabilitation programmes, since health professionals will often recommend a stationary bike be used in the early stages of these. Exercise-based cardiac rehabilitation programmes can reduce deaths in people with coronary heart disease by around 27%;[55] and a patient may feel safer progressing from stationary bikes to e-bikes.[56] They require less cardiac exertion for those who have experienced heart problems.[57]
European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.
Introduction A quick of note of my experiences riding a Moustache Dimanche eBike, kindly provided by Fully Charged, on a spectacular 4 day trip, coast-to-coast across Italy. Overall, an amazing experience in terms of the quality of the ride, the scenery and the new experience of quite painless climbing of the many steep hills. I … Continue reading The joys of crossing Italy coast 2 coast on an eBike – by Andreas Credé
Some components, which are often optional accessories on sports bicycles, are standard features on utility bicycles to enhance their usefulness, comfort, safety and visibility. Mudguards, or fenders, protect the cyclist and moving parts from spray when riding through wet areas and chainguards protect clothes from oil on the chain while preventing clothing from being caught between the chain and crankset teeth. Kick stands keep bicycles upright when parked, and bike locks deter theft. Front-mounted baskets, front or rear luggage carriers or racks, and panniers mounted above either or both wheels can be used to carry equipment or cargo. Pegs can be fastened to one, or both of the wheel hubs to either help the rider perform certain tricks, or allow a place for extra riders to stand, or rest.[citation needed] Parents sometimes add rear-mounted child seats, an auxiliary saddle fitted to the crossbar, or both to transport children. Training wheels are sometimes used when learning to ride.
Electric-assist and other "motorized bicycles"[86] do not need to be inspected, do not require a license, and do not require registration. The vehicle must meet all of the following criteria: a post mounted seat for each person it is designed to carry, two or three wheels which contact the ground, fully operative pedals, wheels at least 16 inches in diameter and a motor not capable of propelling the device at more than 20 mph on level ground. The driver does not need a license, but must be at least 16 years old. DC law prohibits motorized bicycles from traveling anywhere on the sidewalk or in the bike lanes. DC Regulation 18-1201.18 provides: "Except as otherwise permitted for a motor vehicle, no person shall operate a motorized bicycle on any sidewalk or any off-street bikepath or bicycle route within the District. This prohibition shall apply even though the motorized bicycle is being operated solely by human power." So, if cars are prohibited in a particular place, motor-assisted bikes are also prohibited.[87]
The newest entrant in this lower price category is Wing Bikes, a New York City-based company that launched in 2018. Wing wants to be the affordable e-bike for city residents who are sick of shady ride-hailing services and stalled subways. And if you don’t live in a city, that’s fine too: Wing’s e-bikes could be a realistic alternative to owning a car.
"Bicycles" and "Electric Bicycles" are legally defined in the Texas Transportation Code Title 7, Chapter 551 entitled "Operation of Bicycles, Mopeds, and Play Vehicles" in Subchapter A, B, C, and D.[131] Under Chapter 541.201 (24), "Electric bicycle" means a bicycle that is (A) designed to be propelled by an electric motor, exclusively or in combination with the application of human power, (B) cannot attain a speed of more than 20 miles per hour without the application of human power, and (C) does not exceed a weight of 100 pounds. The department or a local authority may not prohibit the use of an electric bicycle on a highway[132] that is used primarily by motor vehicles. The department or a local authority may prohibit the use of an electric bicycle on a highway used primarily by pedestrians.
Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.[5]

Power-assist: Also known as pedal-assist bikes, these are the bicycle equivalents of hybrid cars: they're designed to be pedaled quite a lot of the time and electrically powered either when you're tired or when you feel like a bit of electric help (when you're going up hill, for example). Unlike full-power bikes, they don't have hub motors; instead, there's a separate electric motor mounted near the rear wheel and driving it either through the gear sprocket or simply by pressing against the rear tire. Where a hub motor is difficult or impossible to pedal without any power (because you're effectively turning it into a generator), power-assist motors turn easily with little or no resistance when you pedal. That gives power-assist bikes much greater range than hub-motor ones (as much as 80–145km or 50–90 miles).


The other is our first foray into the larger 45mm wide motor series, similar to those sold by MXUS, QS, Leafbike etc. as 3KW or 5kW hubs. We got these made up to properly fit either a standard 135mm dropout with a single speed freewheel, or a 150mm dropout with a 7-8 speed freewheel and some spacers. As expected from Grin they are sealed, include a 10K thermistor for temperature sensing, and have a disk hole injection port for Statorade, and are hubsink compatible. Check out the performance on our simulator both with and without statorade. Unlike so many other direct drive motors, both of these have the proper alignment for disk rotor position and room for disk calipers without shimming things out.
Storage space: it’s one of the primary disadvantages to biking versus driving. A simple solution is attaching a basket or storage case to your bike’s frame or handlebars, giving you a convenient place to keep your essentials while you ride. A pannier rack is a useful option as well, which allows you to connect special pannier bags to your bike to create even more storage capacity.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.
The body is made from light and durable aluminum. The handlebar comes with simple controls to let you accelerate, brake, monitor battery life, operate headlights and of course…sound the horn. There’s even an USB point that will let you charge your iPhone or Android on the go. The bike can reach a top speed of 10mph. Feel the wind in your hair as you zoom up and down hills and past all that city traffic…

Oklahoma defines an Electric-Assisted Bicycle in 47 O.S. 1-104 [122] as "Two or three wheels; and Fully operative pedals for human propulsion and equipped with an electric motor with a power output not to exceed one thousand (1,000) watts, incapable of propelling the device at a speed of more than thirty (30) miles per hour on level ground, and incapable of further increasing the speed of the device when human power alone is used to propel the device at a speed of thirty (30) miles per hour or more. An electric-assisted bicycle shall meet the requirements of the Federal Motor Vehicle Safety Standards as set forth in federal regulations and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied."


If you are a person who enjoys riding a bike casually at a typical bike path speed (10-15mph), and you like the idea of an ebike push up a hill, against the wind or to relieving a sore knee, then your market for a fully legally defined ebike is very broad and your practical use only has a few limitations. Most ebikes will meet your needs and expectation. I would estimate that 85% of the electric bikes on the market are 100% compliant meeting the federal definition. I encourage you to take the plunge and get a good quality ebike and ride more with assist. Do so with the confidence that electric bikes are here to stay. Coexisting with pedestrians and other cyclist will become a normal part of cycling life.
Photo: Zap Electric's power-assist kit turns a conventional bike into an electric one. There's a bolt-on DC electric motor (weighing just over 3kg or 7lb) just above the back wheel, behind the police officer's foot, pressing against the tire and driving it by simple friction. The motor's powered by a compact lead-acid battery (weighing about 5.5 kg or 12 lb) inside a protective nylon bag. This kit adds quite bit of weight to the bike, but gives extra range and speed when needed. Photo taken in Santa Rosa, California by Rick Tang courtesy of US DOE/NREL.

Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[68]

The last 8 months we've been wrapping up some long duration testing of Statorade across different hub motor lines and performing experiments confirming its long term stability. These results have us pumped to introduce this motor cooling solution beyond DIY'ers and into wider markets. As an example, have a look at the video we below showing the effect this has on a small direct drive folding bike motor.
×