As of 2005, where Federal funds have been used in the construction of bicycle or pedestrian paths motor vehicles including electric bicycles (here defined as having a motor weighing less than Template:Convert) are not permitted unless State or Local regulations permit [25]. This was known as the Transportation Equity Act for the 21st Century (TEA-21), or Public Law 105-178, or by its 2003 re-authorization which expired in 2005 the Safe, Accountable, Flexible, Efficient Transportation Equity Act (SAFETEA-LU).[26][27]

Legislative changes in 2012 significantly altered the classification and regulatory structure for e-bikes. The general effect was to establish electric-assisted bicycles as a subset of bicycles and regulate e-bikes in roughly the same manner as bicycles instead of other motorized devices with two (or three) wheels. Laws 2012, ch. 287, art. 3, §§ 15-17, 21, 23-26, 30, 32-33, and 41. The 2012 Legislature also modified and clarified regulation of e-bikes on bike paths and trails. Laws 2012, ch. 287, art. 4, §§ 1-4, 20.
The other is our first foray into the larger 45mm wide motor series, similar to those sold by MXUS, QS, Leafbike etc. as 3KW or 5kW hubs. We got these made up to properly fit either a standard 135mm dropout with a single speed freewheel, or a 150mm dropout with a 7-8 speed freewheel and some spacers. As expected from Grin they are sealed, include a 10K thermistor for temperature sensing, and have a disk hole injection port for Statorade, and are hubsink compatible. Check out the performance on our simulator both with and without statorade. Unlike so many other direct drive motors, both of these have the proper alignment for disk rotor position and room for disk calipers without shimming things out.
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.

All classes of electric-assisted bicycles may be operated on a fully controlled limited access highway. Class 1 and 2 electric bicycles can be used on sidewalks, but Class 3 bicycles "may not be used on a sidewalk unless there is no alternative to travel over a sidewalk as part of a bicycle or pedestrian path."[143] Generally a person may not operate an electric-assisted bicycle on a trail that is designated as non-motorized and that has a natural surface, unless otherwise authorized.


Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]
Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an electric bicycle dubbed Zike.[7] The bicycle included Nickel-cadmium batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial electric bicycles were available. It wasn’t until 1998 when there were at least 49 different bikes. Production grew from 1993 to 2004 by an estimated 35%. By Contrast, according to Gardner, in 1995 regular bicycle production decreased from its peak 107 million units. Some of the less expensive electric bicycles used bulky lead acid batteries, whereas newer models generally used NiMH, NiCd and/or Li-ion batteries which offered lighter, denser capacity batteries. The end benefits usually varied from manufacturer; however, in general there was an increase in range and speed. By 2004 electric bicycles where manufactured by Currie Technologies, EV Global, Optibike, Giante Lite, Merida, ZAP.

Hmm, that’s unfortunate. I actually have a doctors note that I carry along which recommends the use of an assisted bicycle. I ride thoughtfully and have never been asked to show it. I cannot comment on the federal parks, perhaps they are not aware of the federal law classifying electric assist bikes that perform at or below 20 mph and 750 watts as bicycles. Having a note and this information would be a good response if you were questioned.
Depending on local laws, many e-bikes (e.g., pedelecs) are legally classified as bicycles rather than mopeds or motorcycles. This exempts them from the more stringent laws regarding the certification and operation of more powerful two-wheelers which are often classed as electric motorcycles. E-bikes can also be defined separately and treated under distinct Electric bicycle laws.
There is however still confusion over the various legislations involving Electric Bicycles. This stems from the fact that while places like the US and Canada offer some Federal regulation, the legality of road use is left to the various States or Provinces and then complicated further by municipal laws and restrictions. Further more there are a range of classifications and terms describing them, "Power-assisted bicycle" (Canada) or "Power assisted cycle" (United Kingdom) or ”Electric pedal assisted cycles” (European Union) or simply "electric bicycles", and as such in some cases have varying laws according to their respective classifications in some places.
That aside, the Axis is a fantastic e-bike. At 'only' 16kg, it's almost lively by e-bike standards, but it also feels rock solid. It's geared too low in my opinion – I think it's fair to say I am not the target market – but in 8th, you can breeze on past the legally mandated, electrically-assisted 15.5mph. The hydraulic disk brakes will then bring you to a pleasingly rapid dead stop. The range and charging time are good, too. Cheap it is not, mind you.
Electric bicycles use rechargeable batteries, electric motors and some form of control. This can be a simple as an on-off switch but is more usually an electronic pulse width modulation control. Electric bicycles developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains.[13] The bicycles were then charged from the mains, as is common today. Battery systems in use include lead-acid, NiCd, NiMH and Li-ion batteries.

For a more stylish ride, cast your eyes over the Coboc Rome. It's a full-size bike, with gorgeous stylings, and large wheels that let you pick up plenty of speed on the road. It has a fuss-free approach too, with its automatic motor assistance -- all you need to do is get on and ride. It's very much like any fixed gear bike you'll see on the streets, but with the additional motor, it's less effort to get about.
This article did a good job of trying to justify the assist speed limits but fell short of detailing how that can ever be effectively enforced. In reality the only enforcement that is going to work is applied speed limits to use of bikes and ebikes. For example, it makes sense that a bike lane on a street that the speed limit of vehicles is the speed limit of the bikes/ebikes. On sidewalks and shared pedestrian paths the speed limit probably does need to be in the 15-20mph range to match traditional bikes speeds on those paths.
It’s a topic that many eMTBers are interested in: fast charging. What has long been a reality with electric cars is now also being partly improved for ebikes with high amperage chargers. Bosch has presented a 6A charger this year that can charge a 500 Wh battery in 3 hours, more than a third faster than the standard charger. The new benchmark next year, however, will probably be the 10A charger presented by Haibike and BMZ. It is claimed to be capable of charging a 630 Wh battery in just 1.5 hours.

Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]


The battery is the pedelec’s power source. It supplies the motor with the electrical energy that is required to provide power assistance when cycling. So it is hardly surprising that there is frequent discussion and “talking shop” about the eBike’s battery in particular. What is the difference between batteries? How far can you go on a fully charged battery? What do you have to remember about storage? Thomas Raica, head of technical customer application, here provides information and advice.
Since fat tire electric bikes are suitable for a wider variety of situations than a standard cruiser or commuter e-bike, they have the potential to appeal to more people. For example, hunters and campers are ideal candidates for fat tire e-bikes, as they’ll benefit greatly from the heavy-duty tires and powerful motor when they’re navigating difficult wooded trails with lots of gear.
The are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia[4].
While falling gas prices have temporarily halted years of gains in the number of bicycle commuters, more and more of us are using the bicycle to get around. It’s economical, provides good exercise, and is much cheaper than owning a car. But unless you’re in really good shape, you aren’t going to get very far. Enter the electric bike: a glorious new contraption allows us to get around without having to worry about arriving at our destinations a sweaty mess.

Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3-wheeled bicycle that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Canadian Motor Vehicle Safety Standards (CMVSS) for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1–5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for each. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities.[31]


There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.

There is a lot of information on the internet about electric bikes. Hopefully you have found lots of useful information right here, on this website. Based on this information, you may already have a preference for a specific electric bicycle and / or (technical) components. Your friends that ride e-bikes can also advise you based on their own experiences. But there is only one way you will know if you really make the right choice: take a test drive. During a test drive you will discover how close the riding experience is to your expectations.
However, laws and terminology are diverse. Some countries have national regulations but leave the legality of road use for states and provinces to decide. Municipal laws and restrictions add further complications. Systems of classification and nomenclature also vary. Jurisdictions may address "power-assisted bicycle" (Canada) or "power-assisted cycle" (United Kingdom) or "electric pedal-assisted cycles" (European Union) or simply "electric bicycles". Some classify pedelecs as distinct from other bikes using electric power. Thus, the same hardware may be subject to many different classifications and regulations.
Nebraska defines a Moped as "a bicycle with fully operative pedals for propulsion by human power, an automatic transmission, and a motor with a cylinder capacity not exceeding fifty cubic centimeters which produces no more than two brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than thirty miles per hour on level ground."[69]
FuroSystems’ two new full carbon fiber electric bikes are now available at discounted launch prices! The bikes are a folding e-bike and a mountain e-bike. FuroSystems has designed very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and is currently sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.
The two most common electric motor styles used in today’s e-bikes are hub motors and mid-drive motors. The Freedom uses a hub motor, which was located in the center of the rear wheel. Hub motors typically don’t offer the same natural maneuverability as the increasingly more common (and more expensive) mid-drive motors because their weight is concentrated in the rear of the bike. It can be jarring when the motor prevents you from going faster than the allotted speed, especially when cruising downhill, but 20 mph is the legal maximum for e-bikes in the US. (In the EU, it’s even lower: 25 km/h, or 15.5 mph.)
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
Not all e-bikes take the form of conventional push-bikes with an incorporated motor, such as the Cytronex bicycles which use a small battery disguised as a water bottle.[44][45] Some are designed to take the appearance of low capacity motorcycles, but smaller in size and consisting of an electric motor rather than a petrol engine. For example, the Sakura e-bike incorporates a 200 W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one.[citation needed]
Dryft is a robust, energetic mountain bike, painted in the hues of the setting sun and evening sky. This electric vehicle is designed to take you to those places where no other vehicle can. LightSpeed Dryft an e-Bike that is as fond of adventure as you are. The ideal companion to the thrill seeker in you — wherever you decide to ride, your Dryft always has your back.
When you have the electric motor turned on, it engages with your first push of the pedals. The difference in acceleration is startling compared to any other bike I've ridden. In Eco mode, I could sprint from 0 to 20mph in about 200 feet/65m. Switch to Turbo, and it's about 150/30m feet. As I mentioned above, you still have to pedal. The difference with an electric bike is the feeling of getting more bang for the buck. And if you want to be lazy, you can. Stay in third or fourth gear and you'll be able to stay around 18-19mph with minimal effort. But if you want to go much faster than 20mph, you'll need to work.
The are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia[4].
It should be noted that the definition as written does not define the power of the motor in Watts as is conventionally done for electric bicycles but rather in brake horsepower. Thus for an electric bicycle, motor kit, or electric bicycle motor that is not rated by the manufacture in brake horsepower but rather in Watts a conversion must be made in the units a conversion which is not given in the code of the law and thus the court will have to consider a factor of conversion that is not directly encoded in the law. Industry standard conversion for Watts to horsepower for electric motors is 1 horsepower = 746 watts.[105] Acceptance of that conversion factor from industry, however, as interpretation of the law is subject to the process of the courts since it is not defined specifically in the law.
Most electric bicycles can be locked using keys supplied by the manufacturer. The key is usually inserted into a switch, which is commonly found on the bicycle's handlebars or on one side of the motor compartment. When switched to the "Off" position, the electrical drive system cannot be turned on. In areas of high risk for bicycle theft, these locking mechanisms are used in conjunction with coil or U locks.
Over the last few years, I’ve taken my love of the outdoors, hiking, skiing, trekking and exploring to the next level by starting this site. I started a bike shop in Denver, CO, and have seen amazing growth over the last few years. Getting paid to do what I love has been a dream come true for me. That’s also what led me to start BikesReviewed.com. In my shop, I spend a large amount of time helping people find the perfect bike for them and the style of biking they’re going to be doing. It only made sense that I expanded my reach and got online, making it possible for me to help people all over the world. If biking and staying fit is your priority, too, you’ve come to the right place.
Around the turn of the 20th century, bicycles reduced crowding in inner-city tenements by allowing workers to commute from more spacious dwellings in the suburbs. They also reduced dependence on horses. Bicycles allowed people to travel for leisure into the country, since bicycles were three times as energy efficient as walking and three to four times as fast.
"Electric-assisted bicycle" means a bicycle with two or three wheels, a saddle, fully operative pedals for human propulsion, and an electric motor. The electric-assisted bicycle's electric motor must have a power output of no more than one thousand watts, be incapable of propelling the device at a speed of more than twenty miles per hour on level ground, and be incapable of further increasing the speed of the device when human power alone is used to propel the device beyond twenty miles per hour.[66]
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[94][95] Helmets are required.
Addmotor MOTAN 1000W Electric Bicycle 14.5Ah Lithium Battery Electric Bike 26 Inch Fat Tire Ebike Front Fork Suspension Mountain Beach Snow Pedal Assist M-5500 for Adults Men (Black) Price: $2,699.00 BUY NOW ON AMAZON Full Disclosure: We earn a commission if you click this link and make a purchase, at no additional cost to you. Last Updated: 01/02/2019
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
For people wanting to push the effects of Statorade to the max, the Australian made Hubsinks can clamp on to your motor shell and provide additional cooling fins to shed heat to ambient air. These fit our new MXUS Cassette motors, and the 9C, Crystalyte H, and many others. These are listed on our new store category for motor cooling mods. And like other small products, we try to  keep a stock of 10mL Statorade syringes on Amazon for easy shipping to US customers. They are sold out now but another shipment is inbound. 

Before you start shopping around for a new e-bike, the first thing you should ask yourself is, “how do I plan on using an electric bicycle?” How far do you plan on traveling? What type of terrain will you be traveling on? How much assistance do you need? Do you plan on pedaling – or do you want the bike to do all the work? Is this bike for daily commuting or casual riding? How fast do you need to go?

Bicycle shall mean (1) every device propelled solely by human power, upon which any person may ride, and having two tandem wheels either of which is more than fourteen inches in diameter or (2) a device with two or three wheels, fully operative pedals for propulsion by human power, and an electric motor with a capacity not exceeding seven hundred fifty watts which produces no more than one brake horsepower and is capable of propelling the bicycle at a maximum design speed of no more than twenty miles per hour on level ground.
X-Treme is a very well-known distributor of electric scooters and electric bikes with really great customer service. They offer a number of great budget electric bikes, and one of them is Catalina Beach Cruiser. Powered by 500W rear hub motor, this e-bike can conquer almost any terrain. The frame of this bike is 100% hand-welded aluminum, with a step-though design. The top speed on this bike is about 20 mph, with the range of up to 60 miles on pedal-assist mode. The battery pack is 48V LiPo4. This e-bike is an absolute joy to ride. Even more now, with an all new zero resistance rear hub motor with an automatic clutch. This makes riding without power a breeze and you will feel no resistance from the motor. Seat is large and very comfortable, with dual springs for smooth ride. It also comes with a basket, which is a must have if you plan on going for groceries or running errands on this bike.
Motor position – e-bike motors are positioned on either the front wheel hub, rear wheel hub, or in the middle of the bike between the pedals. There are pros and cons of each, but we think the mid-engine motor gives better weight distribution and the most natural bike riding feel. The pulling sensation you get from a front hub motor in particular can feel a bit unnatural
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
×