On October 22, 2014 PA house bill 573 passed into law, which is Act 154, which changes the definition of "pedalcycle" (bicycle) in the PA state vehicle code. "Pedalcycle" is now defined as a vehicle propelled solely by human-powered pedals or a "pedalcycle" (bicycle) with electric assist( a vehicle weighing not more than 100 pounds with two or three wheels more than 11 inches in diameter, manufactured or assembled with an electric motor rated no more than 750 watts and equipped with operational pedals and travels at speeds less than 20 mph). This bill allows the usage of pedal assisted bicycles in PA that follow the adopted state guidelines.
I bought this bike from a dealer after extensive research on ebikes. The Elby is on par with European commuter ebikes at a better price point, you get a lot for your $ here. Elby is the complete package commuter: lights & a USB charger (for a phone or whatever) are integrated into the motor’s power supply and wired inside the frame. Rugged fenders have heavy-duty cross braces to attach baskets and whatnot. Thick Continental tires make for a comfy ride. The step-through frame is very convenient, built stout enough to carry me (200#) and two loaded baskets down hills and around curves with perfect stability. The motor on this bike is in the rear hub, and having it behind me makes it virtually soundless. The motor (BionX 500 watt) kicks in as soon as you start pedaling, but there is a
In some countries mixed systems, i.e. pedaling and/or using a throttle is legal. In EU countries and Switzerland this is not the case. I.e. you can buy an electric scooter, but this is not considered to be an e-bike in the moped / light scooter category. That kind of hack is probably more difficult, unless the original design has been modified to fit with (s)Pedelec specs. E.g. The Ezee models are of that kind and modifications to revert to the original does not seem to be too difficult...

This was the first ebike I ever bought. I've since become a builder and make my own. But this was a really reliable vehicle. I used it everyday for transportation. The company sent me any part I needed. It's got a power motor on it so it's super reliable. I wouldn't hesitate to buy this bike especially if you're new into the ebike world. If your looking to have some real fun buy this bike.. If your looking to meet new people buy this bike. If looking to go more green buy this bike. This bike is so much fun you well want to ride all day. This bike should be twice the price . I love love love it .
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage. 

The legal definition/description of an electric bicycle is most closely described in the code as a "motorized scooter" in that it is powered by an electric motor and/or human power [45]. It may be also be described as a "Motorized bicycle". However, that description does not include electric powered motor specifically. And it appears that the legal definition "Motorized Bicycle" and "Motorized Scooter" are in conflict. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. A motorized bicycle shall not be operated upon any way, as defined in section one within the commonwealth by any person under sixteen years of age, nor at a speed in excess of twenty-five miles per hour. A motorized bicycle shall not be operated on any way by any person not possessing a valid driver’s license or learner’s permit. Every person operating a motorized bicycle upon a way shall have the right to use all public ways in the commonwealth except limited access or express state highways where signs specifically prohibiting bicycles have been posted, and shall be subject to the traffic laws and regulations of the commonwealth and the regulations contained in this section, except that the motorized bicycle operator may keep to the right when passing a motor vehicle which is moving in the travel lane of the way, and the motorized bicycle operator shall signal by either hand his intention to stop or turn. Motorized bicycles may be operated on bicycle lanes adjacent to the various ways, but shall be excluded from off-street recreational bicycle paths. Every person operating a motorized bicycle or riding as a passenger on a motorized bicycle shall wear protective headgear conforming with such minimum standards of construction and performance as the registrar may prescribe, and no person operating a motorized bicycle shall permit any other person to ride a passenger on such motorized bicycle unless such passenger is wearing such protective headgear.

Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.
Introduction A quick of note of my experiences riding a Moustache Dimanche eBike, kindly provided by Fully Charged, on a spectacular 4 day trip, coast-to-coast across Italy. Overall, an amazing experience in terms of the quality of the ride, the scenery and the new experience of quite painless climbing of the many steep hills. I … Continue reading The joys of crossing Italy coast 2 coast on an eBike – by Andreas Credé
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[94][95] Helmets are required.
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.
Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an electric bicycle dubbed Zike.[7] The bicycle included Nickel-cadmium batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial electric bicycles were available. It wasn’t until 1998 when there were at least 49 different bikes. Production grew from 1993 to 2004 by an estimated 35%. By Contrast, according to Gardner, in 1995 regular bicycle production decreased from its peak 107 million units. Some of the less expensive electric bicycles used bulky lead acid batteries, whereas newer models generally used NiMH, NiCd and/or Li-ion batteries which offered lighter, denser capacity batteries. The end benefits usually varied from manufacturer; however, in general there was an increase in range and speed. By 2004 electric bicycles where manufactured by Currie Technologies, EV Global, Optibike, Giante Lite, Merida, ZAP.
Most electric bicycles can be locked using keys supplied by the manufacturer. The key is usually inserted into a switch, which is commonly found on the bicycle's handlebars or on one side of the motor compartment. When switched to the "Off" position, the electrical drive system cannot be turned on. In areas of high risk for bicycle theft, these locking mechanisms are used in conjunction with coil or U locks.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885.[7][8][9] However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
Hmm, I think it depends on the forest. My experience has been that if you have a Class 1 ebike and are riding respectfully, most places allow it. I have a sensitive knee and carry a doctor’s note citing disability laws in Colorado and have never been approached or asked by a ranger or fellow rider about the legality of my bike. That said, I have been using the really quiet and hidden Brose motor and I ride carefully and am friendly with everyone
Yes, there are less expensive ebikes on the market but most come with a few serious caveats. The Espin Sport delivers on the full promise of an electric bike, but in a more affordable fashion. This bike isn’t going to tow you around for a 60-mile round-trip endeavor but those seeking their first ebike will get plenty of return on their investment with this model.
In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear wheel, or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.
The Ohio Revised Code 4511.01 [121] distinguishes motorized bicycles and mopeds from motorcycles or scooters by describing them as "...any vehicle having either two tandem wheels or one wheel in the front and two wheels in the rear, that is capable of being pedaled and is equipped with a helper motor of not more than fifty cubic centimeters piston displacement that produces no more than one brake horsepower and is capable of propelling the vehicle at a speed of no greater than twenty miles per hour on a level surface." One brake horsepower converts to 0.75 kW, or (rounded) 750W. Thus, a bicycle with an electric helper motor operating under 750W, and not propelling the bicycle over 20 mph, does not qualify to be registered under Ohio state law. Local jurisdictions may have other regulations.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
Controllers for brushed motors: Brushed motors are also used in e-bikes but are becoming less common due to their intrinsic lower efficiency. Controllers for brushed motors however are much simpler and cheaper due to the fact they don't require hall sensor feedback and are typically designed to be open-loop controllers. Some controllers can handle multiple voltages.
Battery – in combination with the motor, this determines how far you can get before your bike needs a recharge. Some don’t provide adequate support on even gentle hills, while the best will comfortably take the strain as the gradient shoots up. Range also varies, with the best e-bike systems we’ve tested able to take you nearly twice the distance of lesser models.
Electric Bicycles are defined by the California Vehicle Code [32][33]. In summary, electric bicycles are to be operated like conventional bicycles in California. There are several exceptions to this. A person must be at least 16 years old, and anyone riding an electric bicycle must wear a bicycle helmet. The e-bikes must have an electric motor that has a power output less than 1,000 watts, is incapable of propelling the device at a speed of more than 20 miles per hour on level ground, is incapable of further increasing the speed of the device when human power is used to propel the motorized bicycle faster than 20 miles per hour, operates in a manner so that the electric motor is disengaged or ceases to function when the brakes are applied, or operates in a manner such that the motor is engaged through a switch or mechanism that, when released, will cause the electric motor to disengage or cease to function.
E-bikes use rechargeable batteries and the lighter ones can travel up to 25 to 32 km/h (16 to 20 mph), depending on local laws, while the more high-powered varieties can often do in excess of 45 km/h (28 mph). In some markets, such as Germany as of 2013, they are gaining in popularity and taking some market share away from conventional bicycles,[1] while in others, such as China as of 2010, they are replacing fossil fuel-powered mopeds and small motorcycles.[2][3]
Electric Motorcycles News (EMN) has been launched in March 2017 and is a personal initiative from graphic designer Guy Salens (Belgium) to inform you about electric motorcycles, electric scooters and some offroad performance e-bikes. EMN collects and publishes all kind of info from available sources on the internet: press releases, existing website content from manufacturers. EMN has also developed a search engine where you can search for e-dealers with your specific keywords, in different countries, different brands and/or categories.
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.
Recent legislation has passed putting Maryland ebike laws in line with the popular class 1,2,3 systems previously implemented in states such as California. This legislation becomes effective October 2019. The most significant portion of this change is the increased max limit on power and speed. It will be increased from a max of 500w / 20mph to 750w / 28mph (assuming the ebike in question meets class 3 criteria)
There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.
FuroSystems is a London-based startup that is launching two new full carbon fiber electric bikes, a folding e-bike and a mountain e-bike. FuroSystems’ ambition was to design very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and to sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]

When I finally had the ability drive this thing in my city, it feels fantastic, you're cruising easily. But the minute it starts going up a hill, you also gotta peddle to help it go up. Which is okay because the little engine helps a lot so you're not straining yourself. But, being that the wheels are so small, after a while, you feel your legs get swore. I guess the size of the wheel
In principle, you would use about 100W (your own energy) for moderate pedalling at 22km/h. If you select 300% assistance (high), that will add another 300W and you can pedal almost twice as fast, i.e. about 27km/h (you will encounter increasing resistance from wind). Therefore, if you got a 400Wh battery, you got a range of about 37km at 37km/h. If go more slowly and use less support (200%), then you can drive further, e.g. 60km with a 400Wh battery. (Read more in die Die Schnellen im Vergleich)
Yes, there are less expensive ebikes on the market but most come with a few serious caveats. The Espin Sport delivers on the full promise of an electric bike, but in a more affordable fashion. This bike isn’t going to tow you around for a 60-mile round-trip endeavor but those seeking their first ebike will get plenty of return on their investment with this model.

The Super Commuter is very aptly named. The 350w Bosch motor will help you sustain speeds of up to 28mph, and the burly, 2.4-inch wide, Schwalbe Super Moto-X 650b tires will keep you secure on even the roughest city streets, and Shimano Deore hydraulic brakes provide ample stopping power. Fenders provide welcome protection from road spray so you arrive at your destination fresh, integrated lights are critical for post-sunset riding, and a side-view mirror hanging on the left side of the handlebar gives a great view of traffic around you. After all, you can ride at the speed of urban traffic on the Super Commuter.


According to Utah Code 41-6a-102 (17) an electric assisted bicycle is equipped with an electric motor with a power output of not more than 750 watts and is not capable of further assistance at a speed of more than 20 MPH, or at 28 MPH while pedaling and using a speedometer. New laws specifically exclude electric pedal-assisted bicycles as "motorized vehicles" and bicycles are permitted on all state land (but not necessarily on Indian Reservations, nor restrictive municipalities, such as in Park City Code 10-1-4.5 2) if the motor is not more than 750 Watts, and the assistance shuts off at 20 mph (Utah Traffic Code 53-3-202-17-a 1). E-bikes sold in Utah are required to have a sticker that details the performance capacity. Children under 14 can operate an electric bicycle if accompanied by a parent/guardian, but children under 8 may not. (Utah code 41-6a-1115.5) No license, registration, or insurance is required by the State but some municipalities may require these measures (Salt Lake City and Provo require registration).
This is a virtual hello to all the people who came by our booth last weekend at the BC Bike Show and are just now visiting our webpage for the first time. We had a great time and were delighted to see how much this event has grown recently. (And to those who lament that the bike show is now totally taken over by ebikes, well it's been over 15 years now that we've been trying to tell you all this day was coming!)
E-bikes can also provide a source of exercise for individuals who have trouble exercising for an extended time (due to injury or excessive weight, for example) as the bike can allow the rider to take short breaks from pedaling and also provide confidence to the rider that they'll be able to complete the selected path without becoming too fatigued[58] or without having forced their knee joints too hard (people who need to use their knee joints without wearing them out unnecessarily may in some electric bikes adjust the level of motor assistance according to the terrain). A University of Tennessee study provides evidence that energy expenditure (EE) and oxygen consumption (VO2) for e-bikes are 24% lower than that for conventional bicycles, and 64% lower than for walking. Further, the study notes that the difference between e-bikes and bicycles are most pronounced on the uphill segments.[59] Reaching VO2 Max, can really help your body as a whole[60]. Professor Janet Lord of Birmingham University in the UK published a study that looked at older cyclists, ““The study looked at muscle mass, blood cholesterol, their VO2 Max, lung function, and in many of those measures we found they didn’t age! No loss of muscle, their bones were a little thin (but nothing like the general population), their blood pressure didn’t go up.[61]
In most jurisdictions, bicycles must have functioning front and rear lights when ridden after dark. As some generator or dynamo-driven lamps only operate while moving, rear reflectors are frequently also mandatory. Since a moving bicycle makes little noise, some countries insist that bicycles have a warning bell for use when approaching pedestrians, equestrians, and other cyclists, though sometimes a car horn can be used when a 12 volt battery is available.[citation needed]
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
×