I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
Justin and Anne-Sophie have been on the road in Europe for about a week now, catching as much sun as they can on the Suntrip. Since the start of the trip in Lyon and the official start of the race in Chamonix, they have been trending on a more southerly route towards Turkey and Iran. As they get used to the style of travel and the nuances of riding a three-wheeled solar vehicle all day they have had their ups...
The motor isn’t insanely powerful, but it gets you up to full speed quickly enough. I never felt like the bike was underpowered. The motor does make more noise than a lot of other hub motor bikes I’ve ridden though. There’s a definite whirrr to the motor caused by the internal plastic gears. While all geared motors will have some level of gear noise, this one stuck out more to me than others.
Artwork: Hub motors aren't the only way to power electric bicycle wheels. If you've ever watched a mouse scampering around inside an exercise wheel, you might have wondered if you could drive a wheel electrically, in a similar way, with something that pushes against the inside of the rim. A company called GeoOrbital has been developing an ingenious mechanical equivalent that can be used to power conventional bikes—and here's a simplified illustration of how it works. It has a motorized drive roller (red) that presses against the inner rim, powered by a battery pack (orange) that sits snugly inside the wheel. Two guide rollers (blue) mounted on a tensioned framework (green) take the place of the conventional arrangement of spokes. According to GeoOrbital, you can fit one of its wheels to a normal bike in just 60 seconds.
Oklahoma the following restrictions on the operation of Electric-Assisted Bicycle in 47 O.S. 11-805.2  as follows: 1. Possess a Class A, B, C or D license, but shall be exempt from a motorcycle endorsement; 2. Not be subject to motor vehicle liability insurance requirements only as they pertain to the operation of electric-assisted bicycles; 3. Be authorized to operate an electric-assisted bicycle wherever bicycles are authorized to be operated; 4. Be prohibited from operating an electric-assisted bicycle wherever bicycles are prohibited from operating; and 5. Wear a properly fitted and fastened bicycle helmet which meets the standards of the American National Standards Institute or the Snell Memorial Foundation Standards for protective headgear for use in bicycling, provided such operator is eighteen (18) years of age or less.
Like most electric bikes, the Rad Wagon is also fairly heavy, weighing 72 pounds. The last drawback is that it comes in only one frame size (which I imagine helps to keep costs lower) that fits rider heights between 5 foot 2 inches and 6 foot 2 inches. My 6 foot 4 husband, however, can ride the bike just fine, so there’s some wiggle room to this range.
It is very important that sensors work well and that they are integrated/tuned for good usability. Although ebikes do need some initial mental adjustment from riders, some model do much better then others, e.g. most testers seem to prefer the TDS Impluse over the Stöckli E.T. over the Stromer (which model?) with respect to reactivity. Of course, usability is subjective and some people may prefer one behavior over an other. However, cheap bikes may be just plain bad and this is why test driving is important.
Electric bicycle usage worldwide has experienced rapid growth since 1998. It is estimated that there were roughly 120 million "ebikes" on the road in China as of early 2010.. The “Electric Bikes Worldwide Reports – 2010 Update” estimates that 1,000,000 electric bicycles will be sold in Europe in 2010. The same report estimates that sales in the USA will reach roughly 300,000 in 2010, doubling the number sold in 2009.
Federal law defines the limits of a low speed electric bike, equating it to a bicycle, and bypassing the definition of a motor vehicle only “For purposes of motor vehicle safety standards…” which means that the manufacturers of these bicycles don’t have to meet federal equipment requirements, and are instead governed by the manufacturing requirements of the Consumer Product Safety Act. There is no mention of exemption from other federal, state, and local traffic laws, or exemption from the definition of a motor vehicle for other purposes.3 This means the law applies to the manufacturer’s product and sale, avoiding federal safety requirements applying to a motor vehicle such as brake lights, turn signals and braking specifications. The goal of the law was to give businesses a legal framework to define and sell low speed electric bikes without the more stringent Federal classification of a motor vehicle. Ebikes that meet the criteria are considered a “bicycle”, do not meet the definition of a motor vehicle, and will be regulated by the Consumer Product Safety Commission. The law also grants the commission authority to add safety requirements to this product. The Federal law supersedes all state laws that equate bicycles to ebikes where the state law is more stringent (lower limits) on power and speed.
Historically, women's bicycle frames had a top tube that connected in the middle of the seat tube instead of the top, resulting in a lower standover height at the expense of compromised structural integrity, since this places a strong bending load in the seat tube, and bicycle frame members are typically weak in bending. This design, referred to as a step-through frame or as an open frame, allows the rider to mount and dismount in a dignified way while wearing a skirt or dress. While some women's bicycles continue to use this frame style, there is also a variation, the mixte, which splits the top tube laterally into two thinner top tubes that bypass the seat tube on each side and connect to the rear fork ends. The ease of stepping through is also appreciated by those with limited flexibility or other joint problems. Because of its persistent image as a "women's" bicycle, step-through frames are not common for larger frames.
Speed Pedelec ebikes – A new classification of bikes called ‘Speed Pedelecs’ have emerged which technically meet the bicycle definition for a 20 mph ebike. These ebikes are designed to max out at 28 mph. Pedelecs are pedal activated vs throttle activated. The weasel words within the definition says, “20mph on motor alone”. Thus, a person who adds their leg power to the motor assist and happens to cruise at 28mph is NOT doing it by motor alone, and therefore the bike is considered to be compliant with the Federal Law. If the rider stops pedaling, the speed pedelec cannot maintain speed. Speed Pedelecs are becoming more popular in Europe and America, which means more models are being offered.
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.