The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].
We take a look at the phenomenon sweeping the trails across Europe – Electric Mountain Bikes. After extensive research and a visit to Eurobike, our team hand-picked what we feel to be the best electric mountain bikes in 2018 using Yamaha, Shimano and Bosch eBike systems. Following the visit to Eurobike, it was clear that … Continue reading Best Electric Mountain Bikes 2018 – The Fully Charged Picks

Oregon Law (ORS 801.258]) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed greater than 20 miles per hour on level ground.[124]


Are you looking for an easier way to get to your blind or tree stand? Or perhaps check all your trail cams in  a fraction of the time it takes today?  Is that sweet spot you know getting harder to reach? When you have to carry 50lbs of gear on your back for 5 or even 10 miles and if you’re lucky you have something to haul back out, using an electric bike built specifically for offroad and woodlands that is also capable of carrying your gear, wouldn’t that make the experience a whole lot more enjoyable? Electric hunting bikes...

Bike is awesome, warranty support has so far delivered, but is a hassle to deal with (and hassle is acceptable and better than nightmare, or unresponsive/clueless/unhelpful/not-english-speaking). To be fair, this is the middle of Swag's busy season. Check tire inflation, check and tighten fasteners, seatpost and handlebars and stem out of the box, RTFM, charge the battery and you're out the door riding quickly.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
The aluminum, step-through eJoy is the happy medium between traditional-looking townies that don’t transport much more than the rider and often cumbersome cargo models that are sometimes a challenge to store. With 26-inch wheels, full fenders, a Shimano Alivio nine-speed drivetrain and disc brakes, a wheelbase similar to the average townie, and a big, comfy seat, it has the appearance of a practical everyday cruiser. But its oversize rear rack, silent Bosch Active Line motor, heavy-duty head tube with front-tray mounts (the tray is an add-on), integrated Supernova E3 lights, and roll-over-anything balloon tires hurtle it into hmm-this-could-actually-replace-my-car status. It’s one of the quietest, most convenient, most stylish, and easiest-to-operate e-bikes available.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
We need to support and put our purchasing power behind ebikes sold in the U.S. that are trying to comply with the California rules which allow 500w and 750w nominal motors and establish 3 classes. If these bikes can create a big enough footprint in the market then future U.S. bike rules may universally adopt these standards. It is better than engaging in regulation showdowns without any standardized and unified proposal on the part of the Electric Bike Community.
Ride1Up 500 series City is a high quality, classy and stylish electric city bike with great features at a really great price. It is designed for the everyday long-distance rider and it features very nice frame geometry that promotes a comfortable upright riding position. Swept-back cafe style handlebars also provide better comfort over longer distances. You can choose between two throttle options – a twist or a thumb throttle, and there are also 3 levels of pedal-assist, or 9 levels if you get an optional LCD screen. Other features include an integrated LED headlight, removable battery with two keys, and heavy duty kickstand. Also we have to commend the amazing customer service, as the guys that are behind this brand are very passionate about what they do, and really motivated to change the way we get around our communities, by providing high-quality bikes at an unbeatable price.
For a more stylish ride, cast your eyes over the Coboc Rome. It's a full-size bike, with gorgeous stylings, and large wheels that let you pick up plenty of speed on the road. It has a fuss-free approach too, with its automatic motor assistance -- all you need to do is get on and ride. It's very much like any fixed gear bike you'll see on the streets, but with the additional motor, it's less effort to get about.
As with all these bikes, the assisted speed is capped at 15mph, but unlike some of them, the Gtech eBike City or its identical (spec-wise) sibling the eBike Sport (this just has a standard frame rather than a step-through one) is light and agile enough for you to be able pedal harder without feeling like the weight is fighting you back down to 15mph. You can even, at a push, use it without the motor on flatter roads.

To qualify as an electric-assisted bicycle under state law they need to have a seat and fully operable pedals for human propulsion, meet federal motor vehicle safety standards, an electric motor that has a power output of not more than 1,000 watts, maximum speed of not more than 20 mph (electric motor and human power combined), disengages or ceases to function when the vehicle’s brakes are applied, two or three wheels
"Bicycle" means either of the following: (1) A device having two wheels and having at least one saddle or seat for the use of a rider which is propelled by human power. (2) A device having two or three wheels with fully operable pedals and an electric motor of less than 750 watts (one horsepower), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden, is less than 20 miles per hour.[citation needed],
Let’s face it – Commuting can be a nightmare. Seemingly infinite price hikes, delays to trains, crammed tubes and congested roads dominate the ways of getting to work. The commuter misery is real. But, what if you could transform this part of the day from a chore to a pleasure? Enter the eBike. The clean, … Continue reading Why an eBike is so good for commuting
Some prohibitions also apply, such as on: carrying cargo that prevents keeping at least one hand on the handlebars or prevents proper use of brakes, riding no more than two abreast on a roadway or shoulder, and attaching the bicycle to another vehicle. Minn. Stat. § 169.222, subds. 3-5. The vehicles may be operated on a sidewalk except in a business district or when prohibited by a local unit of government, and must yield to pedestrians on the sidewalk. Minn. Stat. § 169.223, subd. 3. By default, electric-assisted bicycles are allowed on road shoulders as well as on bicycle trails, bicycle paths, and bicycle lanes.
The BC Bike Show is the premier cycling and outdoors event in Western Canada and is happening in just 2 weeks on March 2nd and 3rd. We'll be there of course, and in addition to our exhibitor booth we'll also be hosting Cycle Stage to give more public presentations. On Saturday at 11:45 am we'll talk on how to navigate the various motor and battery options available for ebike retrofits, and on Sunday at 2pm we'll be doing a live demonstration of a regular bicycle being converted over to electric assist.
Track bicycles do not have brakes, because all riders ride in the same direction around a track which does not necessitate sharp deceleration. Track riders are still able to slow down because all track bicycles are fixed-gear, meaning that there is no freewheel. Without a freewheel, coasting is impossible, so when the rear wheel is moving, the cranks are moving. To slow down, the rider applies resistance to the pedals, acting as a braking system which can be as effective as a conventional rear wheel brake, but not as effective as a front wheel brake.[51]
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]

eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …
The Ancheer comes with outstanding Shimano Tourney gears in 6 x speeds. This gear system is one of the best in the business. Similarly the front-rear disc brakes are perfectly effective and will bring you to a safe stop even from speed. Speaking of speed, the maximum is 16mph and the bike will travel anywhere between 17-23 miles on a single charge. The battery charges up in 4-6 hours, which is the same for virtually all e-bikes.
In general, U.S. and European cycle manufacturers used to assemble cycles from their own frames and components made by other companies, although very large companies (such as Raleigh) used to make almost every part of a bicycle (including bottom brackets, axles, etc.) In recent years, those bicycle makers have greatly changed their methods of production. Now, almost none of them produce their own frames.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
Vehicles with an electric power and power of less than 300W are classified as "not a motor vehicle". Such electric bicycles must comply with the same rules as bicycles. You must wear a helmet even on a scooter or bike under 300W. If the power is over 300W or a combustion engine is used it is a "low powered vehicle" and the moped rules apply. Specifically, a drivers license and registration are required.
Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).
Electrically-assisted cycles are usually classified as either pedelecs or e-bikes. Under European Union regulations adopted in the UK in June 2003, only power-assisted cycles meeting the pedelec classification are considered to be pedal cycles. The maximum power allowed in the European Union for (pedelec) electric bicycles is 250 W, with a maximum assisted speed of 25 km/h.[15]. To meet the pedelec specification the electric motor must be activated by the rider's pedalling effort and the power must cut out completely whenever the rider stops pedalling. Control of the motor by pedalling is often the key difference between a pedelec and e-bike.
GPS Firmware: This net update will be much appreciated by people who have a GPS Analogger device with their CA3. With a simple hardware modification to the Analogger circuit, the GPS data will be transmitted from your existing TRS cable back to the Cycle Analyst. You can then see the time of day, your elevation, position, and direction all on the CA3 screen. The firmware also features additional custom views on the main screen, allowing you to replace or toggle the battery voltage with any of these new parameters to get just the display you are after.
The Ancheer comes with outstanding Shimano Tourney gears in 6 x speeds. This gear system is one of the best in the business. Similarly the front-rear disc brakes are perfectly effective and will bring you to a safe stop even from speed. Speaking of speed, the maximum is 16mph and the bike will travel anywhere between 17-23 miles on a single charge. The battery charges up in 4-6 hours, which is the same for virtually all e-bikes.

In my experience, there aren’t people out checking on ebike classes and the way you ride has a lot more to do with being stopped than what you are riding. I have never been stopped on an ebike anywhere for any reason. The bigger risk is riding a faster and even more powerful electric bike that would be categorized as a moped without a license and that if you got into an accident, you could be liable for more and charged with driving an unregistered vehicle or something. It’s great that you’re being careful and thinking about how to fit into the community, that alone goes a long way


FuroSystems’ two new full carbon fiber electric bikes are now available at discounted launch prices! The bikes are a folding e-bike and a mountain e-bike. FuroSystems has designed very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and is currently sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.

FuroSystems’ two new full carbon fiber electric bikes are now available at discounted launch prices! The bikes are a folding e-bike and a mountain e-bike. FuroSystems has designed very stylish, ultra-light electric bicycles with strong carbon fiber frames that encase all electronic parts and cables – and is currently sell them at a very competitive price. Both of these e-bikes feature high quality, mid-drive motors and offer great range.
The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor. 

Recent legislation has passed putting Maryland ebike laws in line with the popular class 1,2,3 systems previously implemented in states such as California. This legislation becomes effective October 2019. The most significant portion of this change is the increased max limit on power and speed. It will be increased from a max of 500w / 20mph to 750w / 28mph (assuming the ebike in question meets class 3 criteria)

In Quebec power-assisted bicycles are often classified similarly to standard pedal bicycles. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles. The Quebec Highway Safety Code defines a power-assisted bicycle as a bicycle(2 or 3 wheels that touch the ground) with an electric motor with a maximum power of 500W and a top speed of 32 km/h bearing a specific compliance label permanently attached by the manufacturer[30]. PABs are permitted on the road in the province of Quebec, but riders have to be 14 and over to ride the electric bicycle and if they're under the age of 18, must have a moped or scooter license.
In 5 years of working as a bike messenger in Minneapolis, I've ridden all kinds of bikes, in all kinds of weather. I've ridden walmart mountain bikes, 80's classic steel road bikes, kitted out Treks, pretty much everything EXCEPT for fat tire bikes. Such wide tires always seemed... too much. No need for a bike that only makes itself worthwhile maybe two months out of the year, I thought.
It's a solid e-bike, but it's also very heavy one for a folding bike. I found it difficult carry when the bike is folded as the carrying handle is useless, and the center of gravity is towards to the rear wheel so one has to find a place in the rear of the bike to pick it up. Even when the bike is folded, it's bulky and heavy, It's difficult to walk with it while carrying it. It's easy to hurt one's back if he or she is not careful. I would not recommend carrying this bike up or down stairways.
There are specialized bicycle tools for use both in the shop and on the road. Many cyclists carry tool kits. These may include a tire patch kit (which, in turn, may contain any combination of a hand pump or CO2 Pump, tire levers, spare tubes, self-adhesive patches, or tube-patching material, an adhesive, a piece of sandpaper or a metal grater (for roughing the tube surface to be patched), Special, thin wrenches are often required for maintaining various screw fastened parts, specifically, the frequently lubricated ball-bearing "cones".[57][58] and sometimes even a block of French chalk.), wrenches, hex keys, screwdrivers, and a chain tool. There are also cycling specific multi-tools that combine many of these implements into a single compact device. More specialized bicycle components may require more complex tools, including proprietary tools specific for a given manufacturer.

Justin and Anne-Sophie have been on the road in Europe for about a week now, catching as much sun as they can on the Suntrip. Since the start of the trip in Lyon and the official start of the race in Chamonix, they have been trending on a more southerly route towards Turkey and Iran. As they get used to the style of travel and the nuances of riding a three-wheeled solar vehicle all day they have had their ups...
Conversion kits, on the other hand, are sold and installed separately on traditional bicycles. They are harder to setup and conceal, and require some basic mechanical ability and a little bit of ‘elbow grease’ to install. The advantage of conversion kits is that you can choose almost any standard bicycle, and you have the freedom to change or upgrade components as you go. A conversion kit will also allow you to achieve higher power and speed ratings that are not possible on most pre-built electric bike models. Kits are great for tall or heavy riders because they can opt for a larger bike, with higher power and weight carrying capacity. People living in hilly terrain may require the additional torque to handle extremely large inclines. For people who prefer a specific bike model or just love to go faster, a conversion kit offers enormous flexibility.
The Class 3 Aventon Pace 500 urban e-bike has five levels of pedal assist and tops out at 28 mph. But the Pace has something not found on a lot of modern e-bikes. In addition to pedal power, it also has a throttle—in the case of the Pace, a small thumb paddle on the left side of the handlebar next to the control unit that holds at a steady 20 mph, no pedaling required. The bike itself has an aluminum frame, a swept-back handlebar, ergo grips, a sturdy kickstand, hydraulic disc brakes, 8-speed Shimano Altus shifting and gearing, 27.5x2.2-inch Kenda e-bike-rated tires, a saddle the size of Texas, and good ol’ classic city/commuter-bike geometry. It doesn’t come equipped with fenders or a rear rack, but you can add them. Power comes in the form of a 500-watt rear-hub motor, a semi-integrated battery on the down tube (with a range of up to 50 miles), and a backlit display unit mounted on the stem.
×