In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris. The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind). It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.
"Electric-assisted bicycle" means a bicycle with two or three wheels, a saddle, fully operative pedals for human propulsion, and an electric motor. The electric-assisted bicycle's electric motor must have a power output of no more than one thousand watts, be incapable of propelling the device at a speed of more than twenty miles per hour on level ground, and be incapable of further increasing the speed of the device when human power alone is used to propel the device beyond twenty miles per hour.
Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface." This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
What I found most interesting is how my cycling habits changed over my two weeks with the eBike, mostly for the better. In most states, cyclists need to come to a complete stop at stop signs... and as anyone who has ever ridden a bike or shared a road with a cyclist knows, most cyclists generally do an Idaho Stop if they believe it's safe. I do it, too. Knowing that I could quickly get back up to speed with the aid of the electric motor, I found myself more willing to sacrifice my forward momentum and come to a complete stop when there was a car approaching an intersection.
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
In 2012, two e-bike advocates completed the first 4,000-mile (6,400 km) transcontinental e-bike tour from New York to San Francisco to advocate for e-bikes in major cities across the U.S. Pedego Electric Bikes is the best selling brand in the U.S. Many e-bikes in the United States are standard bicycles converted using a kit. In general, the kits include the motor (the majority of which are hub motors built into the front or rear wheel), a speed controller, throttle (usually twist-grip or thumb throttle), necessary wiring and connectors, and a battery. Several U.S. companies offer conversion kits which also offer advanced lithium battery packs. Major manufacturers also offer complete e-bikes. Trek offers a line of e-bikes using the Bionx system in which the rider programs the controller to determine how much effort the motor will give in response to rider effort, from 25% up to 200% of the rider's power. This system ensures a minimum level of rider participation and is also used to comply with many European laws mandating partial human effort before the motor engages.
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
Visually, the Pedego City Commuter Classic Electric Bike is stunning – a smart blend of yesteryear's style and today's technology. Pleasantly high handlebars, a sprung seat, and lovely Schwalbe Fat Frank tires make it very comfortable. Stopping is taken care of by powerful disk brakes, front and rear. Lights are included, as is a useful cargo rack. From an e-bike standpoint, the Pedego Classic City Commuter sports a reliable, hub-mounted motor driven by a 36-volt, 10-amp battery. There's a digital display with a trip computer, odometer, speedometer, pedal assist level, and battery charge information.
We bought 2 of these to go along with our AW 26"x1.75" Front Wheel Electric Bicycle Motor Kits and they work perfectly! The batteries that came with and were recommended by the wheel manufacturer were "clunky", had to be mounted in hanging bags and just didn't work well. These Li-ion Battery with Battery Holders are sleek, fit our Beach Cruisers perfectly, give us a rack to carry our "beach stuff" and one of the best features is how easy they are to charge! They lock in place when we are out and about, but I can unlock them, slide them both out and take them into the RV for charging when we return. Very happy with these and would recommend to anyone looking to convert their current bike into e-bikes!
Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! 
The handlebars connect to the stem that connects to the fork that connects to the front wheel, and the whole assembly connects to the bike and rotates about the steering axis via the headset bearings. Three styles of handlebar are common. Upright handlebars, the norm in Europe and elsewhere until the 1970s, curve gently back toward the rider, offering a natural grip and comfortable upright position. Drop handlebars "drop" as they curve forward and down, offering the cyclist best braking power from a more aerodynamic "crouched" position, as well as more upright positions in which the hands grip the brake lever mounts, the forward curves, or the upper flat sections for increasingly upright postures. Mountain bikes generally feature a 'straight handlebar' or 'riser bar' with varying degrees of sweep backwards and centimeters rise upwards, as well as wider widths which can provide better handling due to increased leverage against the wheel.
Another big upgrade here is the 36V battery. Instead of the 8Ah that the Ancheer had, Rattan has a 10.4Ah battery. The battery actually looks a lot like this one that goes for $190 on ebay or a little more on Amazon. Rattan tells me it is full of genuine LG cells which seem to perform quite well. On cold days, my 15 km (10 mile) very hilly commute would use up about half of the battery (Ancheer would be dying on the way back home). I imagine someone significantly under my 200+lbs could approach the 25 miles Rattan says you can get on throttle alone or up to 50 miles of pedal assist. I’ll just say it was significantly more than the Ancheer.
But the whole is also influenced by the sensory systems which are very different from model to model. E.g. A typical 2013 Panasonic system requires pedalling for optimal support (55/minute?) and has both a pedalling frequency and a speed sensor. You don't get much assistance if you pedal very slowly or very fast. Typically, a rear motor has a force sensor, i.e. you get lots of support fast when you start pedalling in a low gear, i.e. it will "feel" your need for assistance.
Electric bicycles are considered as "bicycles" under Montana law as the law defines bicycles in a two part definition where the first part of the definition describes a conventional bicycle propelled solely by human power and the second part of the definition describes a bicycle equipped with an independent power source for propulsion in addition to foot pedals to permit muscular propulsion. (Montana Code 61-8-102).
By 1898 a rear wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel was patented by Mathew J. Steffens. Also, the 1899 Template:US Patent by John Schnepf depicted a rear wheel friction “roller-wheel” style drive electric bicycle. Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his Template:US Patent. Wood’s device used 4 fractional horsepower motors; each rated less than ½ horsepower and connected through a series of gears.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
The 1968 Vienna Convention on Road Traffic of the United Nations considers a bicycle to be a vehicle, and a person controlling a bicycle (whether actually riding or not) is considered an operator. The traffic codes of many countries reflect these definitions and demand that a bicycle satisfy certain legal requirements before it can be used on public roads. In many jurisdictions, it is an offense to use a bicycle that is not in a roadworthy condition.
Ebike definition in Colorado follows the HR 727 National Law: 20 mph (30 km/h) e-power and 750 W (1 hp) max, 2 or 3 wheels, pedals that work. Legal low-powered ebikes are allowed on roads and bike lanes, and prohibited from using their motors on bike and pedestrian paths, unless overridden by local ordinance. The city of Boulder is the first to have done so, banning ebikes over 400W from bike lanes. Bicycles and Ebikes are disallowed on certain high speed highways and all Interstates unless signed as "Allowed" in certain rural Interstate stretches where the Interstate is the ONLY means of travel.
Under Arizona law, motorized electric bicycles and tricycles meeting the definition under the applicable statute are not subject to title, licensing, insurance, or registration requirements, and may be used upon any roadway authorized for use by conventional bicycles, including use in bike lanes integrated with motor vehicle roadways. Unless specifically prohibited, electric bicycles may be operated on multi-use trails designated for hiking, biking, equestrian, or other non-motorized usage, and upon paths designated for the exclusive use of bicycles. No operator's license is required, but anyone operating a bicycle on Arizona roads must carry proof of identity. A "motorized electric bicycle or tricycle" is legally defined as a bicycle or tricycle that is equipped with a helper motor that may be self-propelled, which is operated at speeds of less than twenty miles per hour. Electric bicycles operated at speeds of twenty miles an hour or more, but less than twenty-five miles per hour may be registered for legal use on the roadways as mopeds, and above twenty-five miles per hour as a registered moped with an 'M' endorsement on the operator's driving license. However, mopeds in Arizona are prohibited from using bike lanes on motor vehicle roadways. The Arizona statute governing motorized electric bicycles does not prohibit local jurisdictions from adopting an ordinance that further regulates or prohibits the operation of motorized electric bicycles or tricycles.
State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour. Subchapter J of Publication 45 spells out the vehicle requirements in full.
Front-Mounted Hub Motor can be found on pre-built bikes or on custom conversions. Mounted to the front wheel, this is the easiest configuration to setup if you’re converting a standard bicycle since there’s no derailleur or chain to worry about. And since most e-bike conversions include batteries mounted to the rear rack, using a front hub motor helps equalize the weight of the bike and makes it easier to handle. But there’s a small risk the motor could cause the front forks to brake. That’s why it’s vital you only use a front hub motor on a steel fork. For pre-built bikes, this shouldn’t be an issue since the motors are usually lower-powered on steel forks.
Range is a key consideration with electric bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. The range of an electric bike is usually stated as somewhere between 7 km (uphill on electric power only) to 70 km (minimum assistance) and is highly dependent on whether or not the bike is tested on flat roads or hills. Some manufacturers, such as the Canadian BionX or American E+ (manufactured by Electric Motion Systems), have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging. This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS.
Most electric bicycles can be classified as zero-emissions vehicles, as they emit no combustion byproducts. The environmental effects of electricity generation and power distribution and of manufacturing and disposing of (limited life) high storage density batteries must be taken into account. Even with these issues considered, electric bicycles will have significantly lower environmental impact than conventional automobiles, and are generally seen as environmentally desirable in an urban environment. The small size of the battery pack on an electric bicycle, relative to the larger pack used in an electric car, makes ebikes very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots," in which ebike riders can charge their vehicles while parked under photovoltaic panels.
Haibike ships the HardNine with 29-inch tires, 180-millimeter hydraulic disc brakes, a 100-millimeter front suspension fork, and a nine-speed Shimano shifting system. The bike’s LCD readout is affixed to the handlebars and displays the current speed, level of charge, remaining range, and current pedal assist mode. The company says the battery can be completely recharged in just four hours, minimizing downtime between rides.