And the last product update to kick off the year is the pilot release of our new Baserunner motor controller. We spent much of last summer and fall trying to cram an even more miniature version of the Phaserunner into compact profile that could fit inside the controller cavity of the popular Hailong downtube battery cradles, and by golly we did it. While not as powerful as the Phaserunner (just 55A max phase current, and 60V max battery voltage), the Baserunner is perfectly suited to the smaller geared and direct drive hub motors using the Higo Z910 plug. This allows for a very tidy installation with no separate controller to mount.
Bicycle suspensions are used primarily on mountain bicycles, but are also common on hybrid bicycles, as they can help deal with problematic vibration from poor surfaces. Suspension is especially important on recumbent bicycles, since while an upright bicycle rider can stand on the pedals to achieve some of the benefits of suspension, a recumbent rider cannot.
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.

First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.

"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,[133][134][135][136][137] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
In Quebec power-assisted bicycles are often classified similarly to standard pedal bicycles. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles. The Quebec Highway Safety Code defines a power-assisted bicycle as a bicycle(2 or 3 wheels that touch the ground) with an electric motor with a maximum power of 500W and a top speed of 32 km/h bearing a specific compliance label permanently attached by the manufacturer[30]. PABs are permitted on the road in the province of Quebec, but riders have to be 14 and over to ride the electric bicycle and if they're under the age of 18, must have a moped or scooter license.
The Freedom’s motor gives you five different levels of boost, and the 36-volt battery offers up to 35 miles of range. You can track your power level and speed, as well as your battery life, on a digital display mounted to the handlebar. I have to admit I spent nearly all my time on the Freedom riding in the highest level, where I could pedal up to 19 mph to 20 mph without even breaking a sweat.

The Netherlands has a fleet of 18 million bicycles.[77] E-bikes have reached a market share of 10% by 2009, as e-bikes sales quadrupled from 40,000 units to 153,000 between 2006 and 2009,[78] and the electric-powered models represented 25% of the total bicycle sales revenue in that year.[77] By early 2010 one in every eight bicycles sold in the country is electric-powered despite the fact that on average an e-bike is three times more expensive than a regular bicycle.[73][78]
An electric bicycle also known as an e-bike is a bicycle with an integrated electric motor which can be used for propulsion. Many kinds of e-bikes are available worldwide, from e-bikes that only have a small motor to assist the rider's pedal-power (i.e., (pedelecs) to somewhat more powerful e-bikes which tend closer to moped-style functionality: all, however, retain the ability to be pedalled by the rider and are therefore not electric motorcycles.
You turn it on by pressing the green button on the battery once for low power and twice for high, although to be honest, there is not a lot of difference between them. After that, you just pedal. There are no gears, no chain to muck up your trousers (a motorbike-style carbon fibre belt is used instead) and not that much difference in feeling compared to riding a normal bike.
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
It should be noted that the definition as written does not define the power of the motor in Watts as is conventionally done for electric bicycles but rather in brake horsepower. Thus for an electric bicycle, motor kit, or electric bicycle motor that is not rated by the manufacture in brake horsepower but rather in Watts a conversion must be made in the units a conversion which is not given in the code of the law and thus the court will have to consider a factor of conversion that is not directly encoded in the law. Industry standard conversion for Watts to horsepower for electric motors is 1 horsepower = 746 watts.[105] Acceptance of that conversion factor from industry, however, as interpretation of the law is subject to the process of the courts since it is not defined specifically in the law.
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170-pound rider when powered only by that engine.[106]

Eight provinces of Canada allow electric power assisted bicycles. The province of Ontario introduced a three-year trial ending October 2009 for these bicycles. In seven of the eight provinces, e-bikes are limited to 500W output, and cannot travel faster than Template:Convert on motor power alone on level ground. In Alberta the maximum output is 750W, and the max speed is 35 km/h.[12] Age restrictions vary in Canada. All require an approved helmet. Some versions (e.g., if capable of operating without pedaling) of e-bikes require drivers' licenses in some provinces and have age restrictions. Vehicle licenses and liability insurance are not required. E-bikes are required to follow the same traffic regulations as regular bicycles. The rules for bicycles assisted by a gasoline motor or other fuel are not included in the regulations government ebikes. These are classified as motor cycles regardless of the power output of the motor and maximum attainable speed.


Some e-bikes operate in pedal-assist only, others have a throttle, and some have both. Generally, pedal-assist only bikes will provide multiple power settings to choose from to help customize your ride, while bikes with both throttle and pedal-assist will have limited pedal-assist options. With these bikes, the throttle provides full control (when needed) while pedal assist is just a secondary option, great on straightaways or open road.
About Terry Brightwater. Terry lives in the Afan Forest, South Wales, UK, with his wife Jay Brightwater. He is a professional Life Coach, specialising in “Emotional Fitness” for over 18 years. Terry’s passion for health and fitness, has spanned over the last 40 years, mainly being expressed through cycling, weight training and healthy eating. He … Continue reading eBikes as a Wonderful Health and Fitness Tool by Terry Brightwater
In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear wheel, or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.
Your local state may have very definite rules as to what is an e-bike, what is a moped, and what is a motorcycle. While ebikes enthusiast don’t want the motor vehicle label, it is certain that each state will define some power level and speed where that classification will apply. Your best source of information is to go directly to your state motor vehicle department website, and get a copy of the your local state vehicle codes, with NO EDITING. Only recently updated official state vehicle codes will contain all the latest changes to the laws.1 For a link to your state MVA, look here:2 http://eco-wheelz.com/electric-bike-laws.php

Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.[23][24][25] 

With hand-operated brakes, force is applied to brake levers mounted on the handlebars and transmitted via Bowden cables or hydraulic lines to the friction pads, which apply pressure to the braking surface, causing friction which slows the bicycle down. A rear hub brake may be either hand-operated or pedal-actuated, as in the back pedal coaster brakes which were popular in North America until the 1960s.
Electric bikes are a green alternative to driving a vehicle. Studies carried out in several towns and cities show that the average car speed in rush hour traffic can dip as low as 18 to 20 mph. Electric bike speed can be as high as 15 mph. With an electric bike, you can reduce pollution, improve fitness, and still arrive at the same time as your car-bound colleagues.
Under the Guide Section of EBR, Court has written a full article, dedicated to the new classification approach, which was initiated by the BPSA (Bicycle Product Suppliers Association), supported by PeopleForBikes, and then Calbikes. The initiative was meant to be pro-active with ebike legislation, to establish self-imposed, measurable, distinct classes of electric bikes before states start hearing about anecdotal problems and potentially overreact to the technology with wide sweeping limitations.
Oregon Law (ORS 801.258) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed no greater than 20 miles per hour on level ground.[54]
The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.
Range is a key consideration with electric bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. The range of an electric bike is usually stated as somewhere between 7 km (uphill on electric power only) to 70 km (minimum assistance) and is highly dependent on whether or not the bike is tested on flat roads or hills.[14] Some manufacturers, such as the Canadian BionX or American E+ (manufactured by Electric Motion Systems), have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[15] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS.

But the good times of the stealthy ebike existence will not endure forever. The ebike market is growing steadily and more so, technology is driving performance up and costs down. The market for a green, lifestyle friendly, transportation technology, with GPS, theft ID, cell service and probably skim lattes is alive and driving an emerging market. It is a matter of time before we all must face and respond to the legal demands of the state and local laws. Not to be over obligatory about being legal and duty oriented, but I do call on my fellow ebikers to ride legal, whether ebike, moped or other. Go ahead and build the 1200W ebike of your dreams, but get it insured and licensed if you must. Such compliance will set the precedence for public acceptance of ebikes in general, and build a track record for expansion and mainstreaming of moped-speed ebikes for commuter value driven needs of the future.
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers.  If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.  
As is the case with any e-bike assembled from Chinese parts, Wing has its share of clones that can be found for sale on sites like IndieGoGo and Kickstarter. For example, the Danish company Strom Bikes has a model for city biking that also looks incredibly similar to Wing’s Freedom — and is apparently several hundred dollars cheaper too. This is also commonly found with electric scooters, with startups buying Chinese-made models and rebadging them for sale in the US.

Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]

What we especially love is how quiet this e bicycle is. If you’re riding down the street or through the park, the gentle hum of the motor is unnoticeable. This is because it’s hidden by the sound of your smooth pedaling. If you’re not into flashy gadgets, any ordinary person would assume you’re riding a conventional peddle bike. This is a great commuter bike.
China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008,[72] and reaching an estimated fleet of 120 million e-bikes in early 2010.[2][73] This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities.[72] Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car.[2] Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007.[73] By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.[72][73]
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.

This is a cool eBike fits in your car's trunk or back seat! It's well made. And it only has one rear disc brake, you dont really need the front brake. It's simple to operate and fun to use - just put one foot on one foot attachment while turning the throttle slightly, then as soon as you start to move add the other foot...and let the joy ride begin!


“Changes in production and consumption patterns are a crucial element of the sustainability agenda. Communication between product developers and users, and user integration in product development, can serve as a means for organizational as well as individual learning processes, resulting in sustainable product development. [...] Improved methods, such as INNOCOPE (innovating through consumer-integrated product development), tested in this study with a cycle manufacturer and resulting in a new product, a pedelec, are needed for effective communication, activating consumers and enabling them to promote sustainability goals. Through co-operative product development processes key factors facilitating and obstructing the adoption of sustainable innovations may be identified. Such processes can enhance the emergence and diffusion of sustainable product innovations and different forms and bodies of knowledge can be combined. Integrating users' contextual everyday knowledge of the product with the technical knowledge of companies may lead to mutual learning, technical innovations and changes in consumer behaviour.” (Hoffmann, 2007).
Many newer or smaller companies only design and market their products; the actual production is done by Asian companies. For example, some 60% of the world's bicycles are now being made in China. Despite this shift in production, as nations such as China and India become more wealthy, their own use of bicycles has declined due to the increasing affordability of cars and motorcycles.[102] One of the major reasons for the proliferation of Chinese-made bicycles in foreign markets is the lower cost of labor in China.[103]
The Pivot Shuttle breaks the mold when it comes to e-mountain bikes. This ballsy, carbon-frame bike, with Shimano Di2, has 140mm of rear travel, 150mm up front, and a 150mm dropper post. A Shimano STePS e8000 drive unit, paired with a 500Wh battery, provides 20 mph of pedal assist, so you can skip the lift line when you hit the bike park and zip right to the good stuff. The 27.5-inch wheels are nimble and eat up nearly anything in their path, and the massive 2.8-inch tires have huge knobs that grip the trail like Velcro.
As with all these bikes, the assisted speed is capped at 15mph, but unlike some of them, the Gtech eBike City or its identical (spec-wise) sibling the eBike Sport (this just has a standard frame rather than a step-through one) is light and agile enough for you to be able pedal harder without feeling like the weight is fighting you back down to 15mph. You can even, at a push, use it without the motor on flatter roads.
To operate a motorized/electric-assisted bicycle on the streets or highways a person must have a valid driver’s license or a motorized bicycle permit. A person under the age of 16 operating a motorized/electric-assisted bicycle under a motorized bicycle permit is subject to restrictions of no passengers (a parent or guardian my ride if the motorized/electric assisted bicycle is equipped with a seat and footrests for a passenger), no night driving, driving on any highway marked as an interstate, must wear a helmet, foot rests for passengers (if designed for passenger(s). A motorized bicycle permit is available to persons of at least 15 years of age who have passed the motorized bicycle test or passed a motorized bicycle course. A motorized bicycle would need the same coverage as a motorcycle would in this state. An electric-assisted bicycle would not need coverage.
×