One of the most important categories of ebikes is the low-cost, entry-level sector. What I call the eBigBox models.  Obviously, not everyone can’t afford a $7500 Riese and Muller and frankly a lot of people are skeptical on how much they will use and enjoy an ebike. So even if they can afford a few thousand dollars for an ebike, they might not want to put it all down on a category they aren’t sure about.
Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
Louisiana Revised Statute R.S. 32:1(41) defines a motorized bicycle as a pedal bicycle which may be propelled by human power or helper motor, or by both, with a motor rated no more than one and one-half brake horsepower, a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which produces a maximum design speed of no more than twenty-five miles per hour on a flat surface. Motorized bicycles falling within this definition must be registered and titled under Louisiana law. Additionally, a motorized bicycle operated upon Louisiana roadways or highways by a person fifteen years of age or older and producing more than five horsepower must possess a valid driver's license with a motorcycle endorsement and adhere to laws governing the operation of a motorcycle, including the wearing of approved eye protectors or a windshield and the wearing of a helmet. The statute also states that "Motorized bicycles such as pocket bikes and scooters that do not meet the requirements of this policy shall not be registered."
Available products (motors, senors, batteries, control systems. etc.) change fast since the e-bike market shows a strong growth. In principle, get a rear motor if you want a lot of raw power and acceleration (e.g. for a 500W motor). Middle motors are more energy efficient and less subject to problems (e.g. overheating). Middle motors usually are combined with integrated rear hub gears, and rear motors with derailleurs. Both have advantages and disadvantages. E.g. the former require less maintenance, are easy to use in go-and-stop traffic, but require taking off weight on pedals when shifting. Therefore the latter (derailleurs) are better for speedy overland and hills cycling.

Having spent some quality time with Wing’s e-bike, I understand why so many people are excited about the growing popularity of electric-powered vehicles like bikes and scooters. They take a lot of the work out of getting from point A to point B, while retaining all of the joy. They can give you more confidence when navigating a treacherous city terrain that prioritizes cars over people. And let’s face it: bikes are cool, and always will be.
The Pivot Shuttle breaks the mold when it comes to e-mountain bikes. This ballsy, carbon-frame bike, with Shimano Di2, has 140mm of rear travel, 150mm up front, and a 150mm dropper post. A Shimano STePS e8000 drive unit, paired with a 500Wh battery, provides 20 mph of pedal assist, so you can skip the lift line when you hit the bike park and zip right to the good stuff. The 27.5-inch wheels are nimble and eat up nearly anything in their path, and the massive 2.8-inch tires have huge knobs that grip the trail like Velcro.

Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]
We spent 46 hours on research, videography, and editing, to review the top choices for this wiki. Thanks to tough, oversized tires and thick frames, fat bikes allow you to take on rugged terrain — such as sand, snow or rocky mountain trails — that would be nearly impossible to manage with a standard bicycle. So imagine what you can accomplish aboard one of these electric models, which are built with motors for extending your rides even further, or for just helping you out on the way back. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best fat tire electric bike on Amazon.
As often preached, eBikes are arguably the most efficient, enjoyable and clean way to travel around the city. Here at Fully Charged, we have an eBike for all, from the eMTBs, to folding electric bikes. But certainly our most popular are urban commuter eBikes. For those bored of playing sardines on the tube, or taking … Continue reading Commuter eBike riding: The Fully Charged Picks

In cities where bicycles are not integrated into the public transportation system, commuters often use bicycles as elements of a mixed-mode commute, where the bike is used to travel to and from train stations or other forms of rapid transit. Some students who commute several miles drive a car from home to a campus parking lot, then ride a bicycle to class. Folding bicycles are useful in these scenarios, as they are less cumbersome when carried aboard. Los Angeles removed a small amount of seating on some trains to make more room for bicycles and wheel chairs.[65]
Ride1Up 500 series City is a high quality, classy and stylish electric city bike with great features at a really great price. It is designed for the everyday long-distance rider and it features very nice frame geometry that promotes a comfortable upright riding position. Swept-back cafe style handlebars also provide better comfort over longer distances. You can choose between two throttle options – a twist or a thumb throttle, and there are also 3 levels of pedal-assist, or 9 levels if you get an optional LCD screen. Other features include an integrated LED headlight, removable battery with two keys, and heavy duty kickstand. Also we have to commend the amazing customer service, as the guys that are behind this brand are very passionate about what they do, and really motivated to change the way we get around our communities, by providing high-quality bikes at an unbeatable price.
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead.  

"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.


China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008,[72] and reaching an estimated fleet of 120 million e-bikes in early 2010.[2][73] This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities.[72] Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car.[2] Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007.[73] By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.[72][73]

To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.
Metro is a brand that has been around since 2010, and it is one of the top sellers. That is mostly because their products are solid, good value, with good power and good features. Metro Hybrid is a part of urban electric bikes family, and it is really well set up for the urban and light trail riding. Metro has a diamond frame and 700c (28-inch) wheels with sporty 38mm Schwalbe Marathon tires, so you get real quality tires. A big capacity battery of 624Wh will carry you 20–40 miles, with the top speed of 28 mph with assist,  or 20mph using throttle only. The comfort is decent with adjustable handle bar, as well as suspension seat post and a suspension fork. Overall, this bike offers good value for the price, with outstanding range and power for its class.
Many countries have enacted electric vehicle laws to regulate the use of electric bicycles. Countries such as the United States and Canada have federal regulations governing the safety requirements and standards of manufacture. Other countries like the signatories of the European Union have agreed to wider-ranging legislation covering use and safety of their term EPAC (electric vehicles)
The U.S. Consumer Product Safety Act states that electric bicycles and tricycles meeting the definition of low-speed electric bicycles will be considered consumer products. The Consumer Product Safety Commission (CPSC) has regulatory authority to assure, through guidelines and standards, that the public will be protected from unreasonable risks of injury or death associated with the use of electric bicycles.[61][62]

Vehicles with an electric power and power of less than 300W are classified as "not a motor vehicle". Such electric bicycles must comply with the same rules as bicycles. You must wear a helmet even on a scooter or bike under 300W. If the power is over 300W or a combustion engine is used it is a "low powered vehicle" and the moped rules apply. Specifically, a drivers license and registration are required.
More powerful pedelecs which are not legally classed as bicycles are dubbed S-Pedelecs (short for Schnell-Pedelecs, i.e. Speedy-Pedelecs) in Germany. These have a motor more powerful than 250 watts and less limited, or unlimited, pedal-assist, i.e. the motor does not stop assisting the rider once 25 km/h has been reached. S-Pedelec class e-bikes are therefore usually classified as mopeds or motorcycles rather than as bicycles and therefore may (depending on the jurisdiction) need to be registered and insured, the rider may need some sort of driver's license (either car or motorcycle) and motorcycle helmets may have to be worn.[14] In the United States, many states have adopted S-Pedelecs into the Class 3 category. Class 3 ebikes are limited to <=750 watts of power and 28 mph.[15]

In general, more expensive bikes are better. However, this is just a trend. E.g. the "Kassensturz" Consumer program from our state TV found in a 2012 study confined to an engineering school, that "Supermarket" bikes, e.g. the 1400 CHF (1200 Euro) "Leopard" bike from COOP did very well. Evaluation is "good" (almost the same as the three times more expensive 25km/h Stromer). They also pointed out a very bad model from a discounter. In other words, you can find good cheap models, but read the tests first.
Vehicles with an electric power and power of less than 300W are classified as "not a motor vehicle". Such electric bicycles must comply with the same rules as bicycles. You must wear a helmet even on a scooter or bike under 300W. If the power is over 300W or a combustion engine is used it is a "low powered vehicle" and the moped rules apply. Specifically, a drivers license and registration are required.
Most consumers want an e-bike that will accommodate its motor without being too cumbersome and will remain stable in spite of its electronic components. Some consumers want only the most basic of e-bike features, including lights, a cargo rack/basket, and a water bottle holder. Others are focused more heavily on safety features, such as brake type. And still others are concerned with convenience and portability.

E-bikes are classed according to the power that their electric motor can deliver and the control system, i.e., when and how the power from the motor is applied. Also the classification of e-bikes is complicated as much of the definition is due to legal reasons of what constitutes a bicycle and what constitutes a moped or motorcycle. As such, the classification of these e-bikes varies greatly across countries and local jurisdictions.
Are there any guidelines you could give on what is legal in Federal Parks that have duel use pedestrian and bike paths. I was recently told that E bikes are not allowed on a Federal trail even though much faster 10 and 20 speed bicycles are common. I also stated that I have a disability which prevents me from walking or biking very far but was still told my bike was not allowed. I should also add that my bike has a top speed of about 15 and is 250 watts.
China's experience, as the leading e-bike world market, has raised concerns about road traffic safety and several cities have considered banning them from bicycle lanes.[2] As the number of e-bikes increased and more powerful motors are used, capable of reaching up to 30 miles per hour (48 km/h), the number of traffic accidents have risen significantly in China. E-bike riders are more likely than a car driver to be killed or injured in a collision, and because e-bikers use conventional bicycle lanes they mix with slower-moving bicycles and pedestrians, increasing the risk of traffic collisions.[2]

E-bikes are classified in three different types: Class 1 and Class 3 bikes are powered proportionally to the “input” a rider gives via pedaling. “It feels natural, and you’re still riding a bike, so all your reflexes, skill and comfort you’ve developed over years of riding bikes apply immediately,” says Fritz Rice, sales manager of Gregg’s Cycles, near Greenlake.
I had gotten this to build an electric bike but I have never worked with wires before so I didn't realize that we needed to attach our own connectors to the wires. The person who I talked to at Joyisi was super nice and explained that to me and even offered to send me connectors for free. I had already ended up getting a different bike altogether though and so I just wanted to return the battery. But because I am returning it for my own reasons (as opposed to the battery being faulty), they would normally have me pay for return shipping and deduct the cost of shipping to me (which is a lot, because they are international) and the inspection fee from my refund, but they were super nice and offered to take on most of the costs and I would only have to pay for the return
State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[55] Subchapter J of Publication 45 spells out the vehicle requirements in full.

The Riese & Müller Load Touring HS is billed as “the ultimate minivan of e-bikes,” and it holds up to that claim. With a low center of gravity (aided by the 20-inch front and 26-inch rear wheels), the Load is easy to handle. Tektro hydraulic disc brakes add control, and front and rear suspension provide comfort. The Bosch motor offers an assist up to 275 percent of your effort until you hit 28 mph, when it cuts out. Two 500Wh batteries give you 12 hours or more of range at full power. It’s capable of toting up to 220 pounds of pets, people, and less-animate cargo. R&M also sells a double child seat for kids up to age 6 and a child-seat fastener for your youngest passengers.
Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
×